Model EHA3201 EnviroNET G.SHDSL Router Quick Start Guide Important—This is a Class A device and is intended for use in a light industrial environment. It is not intended nor approved for use in an industrial or residential environment. Part Number: 07MEHA3201-QS, Rev. B Revised: July 21, 2011 Sales Office: +1 (301) 975-1000 Technical Support: +1 (301) 975-1007 E-mail: support@patton.com WWW: www.patton.
WARNING • Do not open the device when the power cord is connected. For systems without a power switch and without an external power adapter, line voltages are present within the device when the power cord is connected.
Electrostatic Discharge (ESD) can damage equipment and impair electrical circuitry. It occurs when electronic printed circuit cards are improperly handled and can result in complete or intermittent failures. Do the following to prevent ESD: WARNING • Always follow ESD prevention procedures when removing and replacing cards. • Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact.
1.1 Grounding the EHA3201 Before installing the EnviroNET G.SHDSL Router, it is important to establish a good grounding connection first. 1. Assemble a ground wire using #10 AWG wire with green-and-yellow-colored insulation and two ring terminals. Make the wire long enough to reach one of the following earth ground sources: •The building ground rod (generally located at the site’s main service entrance) •A sprinkler system pipe •A cold-water pipe •Building structural steel 2.
1 TX+ (data output from the G.SHDSL router) 1 2 3 4 5 6 7 8 2 TX- (data output from the G.SHDSL router) 3 RX+ (data input to the G.SHDSL router) 4 (no connection) 5 (no connection) 6 RX- (data input to the G.SHDSL router) 7 (no connection) 8 (no connection) Figure 3. EnviroNET G.SHDSL Router 10/100Base-T RJ-45 Connector Pinout 1.4 Connecting Power The EHA3201 is an internally powered unit. The power connection is made via the 3-pin power connector on the bottom panel of the EnviroNET G.SHDSL Router.
Note It does not matter whether the positive (+) or negative (-) side of the DC power supply is grounded. However, the polarity on the power source must be matched up properly to the EHA3201 power input (i.e. negative power source terminal to negative power input; positive power source terminal to positive power input). 2.0 Configuring the EHA3201 The EnviroNET G.SHDSL Router comes pre-configured to communicate with other devices on the network.
2.2 Configuring applications The EHA3201 is typically used in a bridged or routed application. For instruction on how to configure the EHA3201 for an application, refer to the Model 3201 & 3241 User Manual. Bridged Applications • For a bridged application connecting standalone units back-to-back, see pages 29-32 in the Model 3201 & 3241 User Manual. • For a bridged application connecting the CPE to a DSLAM, see pages 38-46 in the Model 3201 & 3241 User Manual.
B.0 EHA Case Specifications B.1 Power Requirements • UAC: 110, 220VAC, 2.25W B.2 Temperature Range • -40–185°F (-40–85°C) B.3 Humidity • Up to 90% non-condensing. B.4 Dimensions • 8”H x 9.25”W x 3.25”D B.5 Weight • 6.4lb (2.9kg) Note For Model 3201 unit specifications, refer to the Model 3201 & 3241 User Manual located on the CDROM shipped with your EHA3201 and available online at www.patton.com/manuals.
C.0 Compliance Information C.1 Compliance EMC: • FCC Part 15, Class A • EN55022, Class A • EN55024 Safety: • UL 60950-1/CSA C22.2 N0. 60950-1 • IEC/EN60950-1 • AS/NZS 60950-1 PSTN Regulatory: • FCC Part 68 • CS-03 • AS/ACIF S043:2003 C.2 FCC Part 68 (ACTA) Statement This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA. On the bottom side of this equipment is a label that contains—among other information—a product identifier in the format US: AAAEQ##TXXXX.
3.3 Industry Canada Notice This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.
C.5 EC Declaration of Conformity Product Description: Models 3201 & 3241 We certify that the apparatus identified above conforms to the requirements of Council Directive 1999/5/EC on the approximation of the laws of the member states relating to Radio and Telecommunication Terminal Equipment and the mutual recognition of their conformity. The safety advises in the documentation accompanying the products shall be obeyed. The conformity to the above directive is indicated by the CE sign on the device.
Copyright statement Copyright © 2011, Patton Electronics Company. All rights reserved. The information in this document is subject to change without notice. Patton Electronics assumes no liability for errors that may appear in this document. Trademarks statement The term EnviroNET is a trademark of Patton Electronics Company. All other trademarks presented in this document are the property of their respective owners.
D.0 Buccaneer 400 Series Environmentally Sealed Connectors IMPORTANT EHA3201 Quick Start Guide The following instructions are provided by Bulgin UK for assembling the 400 Series Buccaneer IP68 Sealed Electrical Cable Connectors.
EHA3201 Quick Start Guide
EHA3201 Quick Start Guide 15
EHA3201 Quick Start Guide
