Model 3196RC iDSL TDM-Digital Access Concentrator (T-DAC) User Manual Sales Office: +1 (301) 975-1000 Technical Support: +1 (301) 975-1007 E-mail: support@patton.com WWW: www.patton.com Part Number: 07MD3196RC-GS, Rev.
Patton Electronics Company, Inc. 7622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel: +1 (301) 975-1000 Fax: +1 (301) 869-9293 Support: +1 (301) 975-1007 Web: www.patton.com E-mail: support@patton.com Copyright © 2012, Patton Electronics Company. All rights reserved. The information in this document is subject to change without notice. Patton Electronics assumes no liability for errors that may appear in this document.
Summary Table of Contents 1 Introduction .................................................................................................................................................. 16 2 Hardware installation.................................................................................................................................... 24 3 Configuring the T-DAC for operation ..........................................................................................................
Table of Contents Summary Table of Contents ........................................................................................................................... 3 Table of Contents ........................................................................................................................................... 4 List of Figures ................................................................................................................................................. 7 List of Tables ..
Model 3196RC T-DAC User Manual Connecting the Ethernet ports ........................................................................................................................27 Connecting the 10/100Base-T Ethernet port to an Ethernet switch or hub ...............................................27 Connecting the 10/100Base-T Ethernet port to an Ethernet-capable workstation or PC ................................28 Connecting the EIA-561 RS-232 configuration port (DCE configured) ......................
Model 3196RC T-DAC User Manual Remote loop ..............................................................................................................................................75 Line Loop .................................................................................................................................................76 T1/E1 port test modes ....................................................................................................................................
List of Figures 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 Ferrite location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Model 3196RC T-DAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Model 3196RC T-DAC features . . . . . . . .
Model 3196RC T-DAC User Manual 48 49 50 51 52 53 54 55 56 57 58 59 60 61 3196RC Configuration Menu home page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 IMPORT/EXPORT page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Example T-DAC flash memory configuration file displayed in a browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
List of Tables 1 2 3 4 5 6 7 8 9 10 General conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Mouse conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 LED definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compliance Information Radio and TV Interference The Model 3196RC generates and uses radio frequency energy, and if not installed and used properly—that is, in strict accordance with the manufacturer's instructions—may cause interference to radio and television reception.
Model 3196RC T-DAC User Manual Industry Canada Notice Note CAUTION This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.
Model 3196RC T-DAC User Manual pany for leased line facilities. The Universal Service Order Code (USOC) is RJ48. The Facility Interface Codes (FIC) are 04DU9-BN, 04DU9-DN, 04DU9-1KN, and 04DU9-1SN. The Service Order Code (SOC) is 6.0N. Facility Interface Code Service Code Network Connection 1.544 Mbps SF format without line power 04DU9-BN 6.0N RJ-48C 1.544 Mbps SF and B8ZS without line power 04DU9-DN 6.0N RJ-48C 1.544 Mbps ANSI ESF without line power 04DU9-1KN 6.0N RJ-48C 1.
About this guide This guide describes installing and configuring a Patton Electronics Model 3196RC TDM-Digital Access Concentrator (T-DAC). By the time you are finished with this guide, your T-DAC will be connected to the remote DSL modems and transferring data.
Model 3196RC T-DAC User Manual Precautions Notes and cautions, which have the following meanings, are used throughout this guide to help you become aware of potential T-DAC problems. Warnings relate to personal injury issues, and Cautions refer to potential property damage. Note Calls attention to important information. WARNING The shock hazard symbol and WARNING heading indicate a potential electric shock hazard. Strictly follow the warning instructions to avoid injury caused by electric shock.
Model 3196RC T-DAC User Manual Table 1. General conventions Convention Meaning Garamond bold type Indicates the names of command buttons that execute an action. <> Angle brackets indicate function and keyboard keys, such as , , , and so on. Are you ready? All system messages and prompts appear in the Courier font as the system would display them. % dir *.
Chapter 1 Introduction Chapter contents Model 3196RC iDSL T-DAC overview ................................................................................................................17 Hardware overview ................................................................................................................................................18 WAN .........................................................................................................................................................
Model 3196RC T-DAC User Manual 1 • Introduction Model 3196RC iDSL T-DAC overview The Model 3196RC (see figure 2) provides 16 iDSL subscriber ports and 4, 8, 12, or 16 T1/E1 WAN uplink ports. A built-in digital cross-connect switch provides completely flexible grooming: the capability to connect any DS0-channel to any other DS0-channel from the WAN uplink ports or the iDSL ports.
Model 3196RC T-DAC User Manual 1 • Introduction Hardware overview The Model 3196RC combines transmission and networking technology concentrating 16 iDSL ports and 4 to 16 T1/E1 WAN links into a single slot blade for a standard CPCI chassis. The T-DAC front blade (see figure 3) contains a full set of LED status indicators presented on the front panel, and an RS-232 async control port. The rear blade presents electrical connections for the iDSL modems and WAN ports as well as an alarm LED.
Model 3196RC T-DAC User Manual 1 • Introduction LAN The 10/100-Mbps Ethernet LAN port is presented on an RJ-45 connector with an auto-sensing/full-duplex 10Base-T or 100Base-T interface. Also included are: • 100Base-TX half-/full-duplex operation (100 + 100) • 10Base-T half-/full-duplex operation (10 + 10) • Auto detection and fallback • 10/100 Mbps link and status indicators RS-232 control port The RS-232 port provides for initial configuration of the Model 3196RC.
Model 3196RC T-DAC User Manual 1 • Introduction System timing The iDSL T-DAC's system timing may be derived from an internal clock from an on-board chip, a CPE iDSL modem, a network clock from one of the T1/E1 WAN ports, or an external 64-kHz BITS (building integrated timing supply) reference clock. The system timing is configured through the NMS.
Model 3196RC T-DAC User Manual 1 • Introduction SYSTEM LED POWER LED POW ALARM LED CPU ALA ETHERNET LED ETH FA I ERR TM WA N WAN LED RCE OR ODE DSL 1 2 9 10 11 12 13 14 15 16 DSL CONNECTION 3 4 5 6 7 DSL CONNECTION LEDs ET SOU CLK TES L TEM ERN CLK CLK ERROR LED ER RM SYS CLK SOURCE LED TEST MODE LED RC T-DAC oncentrator CPU LED 8 10/100 ENET port 10/100 ENET CONFIG port CONFIG READY READY LED Figure 4.
Model 3196RC T-DAC User Manual 1 • Introduction Table 3. LED definitions (Continued) LED CLK SOURCE Color Status Green Meaning On solid The 3196RC is set as the Master Clock source. Flashing The 3196RC is set as the secondary clock source. Off CLK ERROR The 3196RC is set as the slave, getting its clock from the H.110 Bus. Yellow On solid Master Clock source has been lost and the 3196RC is using the secondary source for its clock.
Model 3196RC T-DAC User Manual 1 • Introduction Approvals The Model 3196RC T-DAC has achieved the following approvals and certifications: • Safety - UL 60950 - Industry Canada CSA C22.2 No.
Chapter 2 Hardware installation Chapter contents Introduction ..........................................................................................................................................................25 Unpacking the Model 3196RC T-DAC ................................................................................................................25 T-DAC blades installation......................................................................................................................
Model 3196RC T-DAC User Manual 2 • Hardware installation Introduction This chapter contains the following procedures for installing the Model 3196RC T-DAC: Note Before installing the T-DAC, you will need to obtain the line type and encoding of the T1/E1 line from your local telephone company (Telco).
Model 3196RC T-DAC User Manual Note 2 • Hardware installation The T-DAC should be installed as close as possible to the termination jack provided by the Telco. The location should be well ventilated. Do not block the rack chassis’ cooling vents. 2. Insert the rear blade into the desired slot in the rack chassis. Make sure the blade is seated properly in the slot guides. Card handle Alignment/ESD pin Figure 5. Alignment/ESD pin and card handle 3.
Model 3196RC T-DAC User Manual 2 • Hardware installation Cable installation This section describes installing the network interface cables. Connecting the Ethernet ports The T-DAC has a single 10/100 Ethernet interface for connection to your LAN (figure 6). The Ethernet port will autosense the correct speed of the local LAN and automatically negotiate half or full-duplex operation. This section describes connecting the T-DAC to the Ethernet LAN via an Ethernet hub, switch, or workstation.
Model 3196RC T-DAC User Manual 2 • Hardware installation Figure 7. Ethernet RJ-45 pin and signal definitions for T-DAC Connecting the 10/100Base-T Ethernet port to an Ethernet-capable workstation or PC The 10/100Base-T Ethernet port can connect to a single Ethernet-capable workstation or PC by means of a cross over cable. Refer to figure 8 to assemble a cross-connect cable that will connect between the NIC Ethernet port in the workstation and the T-DAC 10/100Base-T Ethernet port. Figure 8.
Model 3196RC T-DAC User Manual 2 • Hardware installation Connecting to the T1/E1 WAN ports An active T1/E1 is not necessary to configure the T-DAC. However, an active T1/E1 connection is required when mapping iDSL modems to specific time slots in the T1/E1 ports or even for mapping WAN time slots to other WAN time slots. The factory-set default configuration of the Model 3196RC has the T1/E1 ports disabled.
Model 3196RC T-DAC User Manual 2 • Hardware installation 2. The other end of the cable has 68 non-terminated twisted-pairs for connection to a punch-down block (see table 4). Select the twisted pairs for the WAN ports that will be activated and terminate them on the punch-down block. Table 4.
Model 3196RC T-DAC User Manual 2 • Hardware installation Connecting the iDSL ports The remote (CPE) iDSL modems are connected to the T-DAC via the RJ-21X cable (see figure 12). Pin 1 25 50-pin TELCO Male 50 26 Figure 12. RJ-21X connector 1. Connect the RJ-21X connector of the cable into the 50-pin RJ-21X receptacle on the rear of the 3196RC. 2. The other end of the cable has 25 non-terminated twisted-pairs for connection to punch-down blocks.
Model 3196RC T-DAC User Manual 2 • Hardware installation Table 5.
Model 3196RC T-DAC User Manual Note 2 • Hardware installation To synchronize the ForeFront system with a BITS clock, you must connect the site BITS clock system to the EXT CLOCK connector located on the rear-panel of the T-DAC WAN Access Module rear card (see figure 13). D S L W A N LE U OD SS M CE AN W AC K OC T Y AD RE M EX CL EXT CLOCK connector AR AL Pin 1 EXT CLOCK Pin 3 Figure 13.
Model 3196RC T-DAC User Manual 2 • Hardware installation Completing the hardware installation This section verifies that the T-DAC hardware is operational to the point where you can begin configuring the software settings. Power is delivered from the CPCI chassis backplane through the 47-pin PICMG 2.11 power connectors on the 3196RC blades. Upon insertion into the CPCI chassis, the Model 3196RC immediately powers up and begins its boot cycle. During the boot cycle the following should occur: 1.
Chapter 3 Configuring the T-DAC for operation Chapter contents Introduction ..........................................................................................................................................................36 Configuration prerequisites ...................................................................................................................................36 Initial configuration through the RS-232 control port..............................................................
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation Introduction This chapter contains the following procedures that describe configuring the Model 3196RC T-DAC for operation: • “Configuration prerequisites”—lists the items you need to have on hand before configuring the T-DAC. • “Initial configuration through the RS-232 control port” on page 37—describes how to define the 3196RC’s LAN IP address and netmask parameters.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation • If you are using a T1 WAN line, you will need the following information from the telephone company (central office): - Line Type: either ESF or D4 - Line Coding: either B8ZS or AMI • If you are using a E1 WAN line, you will need the following information from the Telco: - Line Type: either E1 or E1-CRC - Line Coding: either HDB3 or AMI Initial configuration through the RS-232 control port Initially you must configure the 3196RC’s IP
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation Setting up the HyperTerminal (or similar program) session Do the following: 1. At your PC, find the file HYPERTRM.EXE. Open a HyperTerminal session by double-clicking on the file name. Figure 15. Connection Description window 2. Type a connection name (e.g., 3196RC Config), select an icon, then click OK (figure 16). Figure 16. Connect To window 3.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation 6. Configure your COM port settings as shown in figure 17, then click OK. Figure 17. COM1 Properties window 7. Click on the File menu, then select Properties. 8. Configure the settings for Function, arrow and ctrl keys act as to Terminal keys as shown in figure 18, then click OK. Figure 18.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation 9. Connect the male end of the 3196RC T-DAC’ power cables to the power outlets. 10. Boot up information will display on your HyperTerminal connection window, eventually followed by a login request window (see figure 19). Figure 19. Login window 11. For the user name, type superuser. 12. For the password, type superuser; the TOP LEVEL MANAGEMENT window then appears (see figure 20). Figure 20. VT-100 Top Level Management window 13.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation 19. Press the left-arrow cursor key until the TOP LEVEL MANAGEMENT window displays. 20. Select a for Home, then press . 21. Under the Current Status page, type 1 (store Config(1)) to save the changes you have just made to the configuration. This completes the initial configuration of the Model 3196RC. The next steps in configuration will be done using your Web browser connected via Ethernet to the 3196RC.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation 5. The 3196RC Configuration Menu home page will appear (see figure 21). Figure 21. 3196RC Configuration Menu home page Home page overview The HOME window is divided into two panes: the Configuration Menu pane and the Configuration/information pane (see figure 22).
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation Configuration Menu pane Configuration/information pane Figure 22. HOME page window panes Figure 23. Immediate Actions buttons From the Home page, the following actions can be performed: • Record Current Configuration—clicking on this button (see figure 23) saves the current configuration from volatile DRAM memory to FLASH memory.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation figuration changes will be lost if the power to the Model 3196RC is turned off. • Hard Reset—this button (see figure 23) causes the Model 3196RC to perform a cold restart. When you select Hard Reset, the T-DAC confirms that you want to execute this command. Then, the T-DAC will disconnect all current sessions, re-initialize the interfaces, and re-load configuration parameters from FLASH.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation 4. To enter the default gateway, use the first Add a route line. The Destination shall remain 0.0.0.0, and there is no mask to enter. 5. In the Gateway box, type your default gateway IP address for the 3196RC. 6. Click the Add Route button to save your configuration. Figure 25. IP Routing Information window 7. The route which you already see in the table appeared upon the configuration of the LAN IP address. 8.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation Unless it fails or becomes disconnected, the main reference provides the system clock for the 3196RC. Should this failure occur, the fallback reference will be the clocking source for the 3196RC’s system clock. Example 1 Your 3196RC is the only blade in the chassis and must be configured as the system clocking master. This example assumes you will use WAN port #1 as the main reference and WAN port #2 as the fallback reference.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation 2. Click the System Clocking hyperlink on the 3196RC Configuration Menu to open the System Clocking Configuration page (see figure 27). Figure 27. System Clocking Configuration page, example 2 3. For Clock Reference select slave(3). 4. For Main Reference select system(500). 5. For Fallback Reference select wan-1(1). 6. Click the Submit Query button. 7. Select enable(1) to enable the fallback reference clock. 8.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation The DS0 Mapping window (Digital Cross Connect Configuration) provides full DS0 grooming and supports three variations. You may define connections between (1) an iDSL modem and a WAN port, (2) two iDSL modems, or (3) two WAN time slots. (When no mapping is defined, neither the iDSL modems nor the WAN ports have any destination). To define the DS0 Mapping for the iDSL modems, do the following: 1.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation The following notation should be used for assigning timeslots: • dash: (-), e.g., 1-3 • comma: (,), e.g., 1,4,9 • combo: 1-2,3,6-7 Examples for configuring static connections. Three examples are provided: • Example 1: Connecting an iDSL modem port to an E1 WAN port. • Example 2: Connecting an E1 WAN port to another E1 WAN port. • Example 3: Connect an iDSL modems port to another iDSL modem port.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation 8. On the 3196RC Configuration Menu, click the iDSL hyperlink to open the iDSL Port Configuration page (figure 30). Using your mnemonic naming convention scheme, enter a name for this connection in the Circuit ID field to the right of Port #3 (optional). Figure 30.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation 9. On the Configuration/information pane, click on the number 3 under the column titled Port # to open the iDSL Port 3 Details page (see figure 31). Figure 31. iDSL Port 1 Details page 10. Click the Change Config button to open the configurable parameter fields (see figure 32). Figure 32. iDSL Port configurable parameters 11. Near the bottom of the pane, change Serial Data Rate to 144k(5) and click the Submit button.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation Connect an E1 line, (WAN) Port 2, timeslots 1 - 31, to another E1 line, (WAN) Port 3, timeslots 1 - 31. Solution: 1. Under Dev Type A, select t1-e1(1). 2. Under Dev Num A, select port2(2). 3. Under Dev Slots A, enter 1 - 31. 4. Under Dev Type B, select t1-e1(1). 5. Under Dev Num B, select port3(3). 6. Under Dev Slots B, enter 1 - 31. 7. Click the Submit Query button You have completed the configuration for example 2.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation 15. Click the Submit button at the bottom of the page. 16. Repeat steps 9 through 15 for iDSL modem port 16. You have completed the configuration for example 3. Example 4 Mapping between different blades. Connect WAN port 1, time slot 1 on Blade Number 1 to WAN port 7, time slot 31 on Blade Number 3. Solution: Complete the following steps. 1. Go to blade number 1. 2. Under Dev Type A, select t1-e1(1). 3.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation Activating the iDSL ports Do the following to activate an iDSL port: 1. On the 3196RC Configuration Menu, click the DSL hyperlink to display the iDSL Port Configuration page (see figure 33). (Optional: Using your mnemonic naming convention scheme, enter a name for this connection in the “Circuit ID” field to the right of the Port # you wish to activate). Figure 33. iDSL Port Configuration window 2.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation • Front panel switches • DTE test mode • User ID Do the following to configure the iDSL port parameters on the Patton CPE device: 1. On the 3196RC home page click the DSL hyperlink to display the iDSL Port Configuration page.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation 2. Scroll to the table row for the port which connects to the Patton CPE device, and click the port number hyperlink to display the iDSL Port # Details page.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation 3. Click the [change configuration] button to display the configurable parameters for the Patton CPE device on the right-hand side of the page (see below). 4. Use the drop-down menus to set the configurable parameters to your desired values. 5. Click the [submit] button to record your changes on the remote Patton CPE. You will automatically return to the iDSL Port # Details page.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation Figure 35. T1/E1 Link Activity Ports 1 – 4 page. 3. Click the Configuration… hyperlink then click the Modify Configuration... hyperlink to open the WAN Circuit CONFIGURATION LINK window (see figure 36) and view the Line Interface Settings. Figure 36. WAN Circuit Configuration page, Line Interface Settings Configuring the E1 line interface settings 1. From the Line Type pull-down menu (figure 37) select dsx1E1(4) or dsx1E1-CRC(5).
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation 2. From the Line Coding pull-down menu (figure 38) select dsx1AMI(5) or dsxHDB3(3). Most installations will use HDB3. Figure 38. Line Coding pull-down menu with dsx1HDB3(3) selected 3. From the Line Build Out pull-down menu (figure 39) select e1pulse(1). Figure 39. Line Build Out pull-down menu with e1pulse(1) selected 4. Click the Submit Query button to apply your line interface settings.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation Configuring line settings and signaling for T1 Accessing the Line Interface Settings 1. On the 3196RC Configuration Menu, click the T1/E1 Link hyperlink to open the T1/E1 LINK ACTIVITY OVERVIEW page (figure 41). Figure 41. T1/E1 Link Activity Overview page 2. View Link 1 corresponds to the first WAN circuit on the T-DAC. To the right of View Links 1-4 click the View Links...
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation 3. Click the Configuration… hyperlink, then click the Modify Configuration... hyperlink to open the WAN Circuit CONFIGURATION LINK window (figure 43) and view the Line Interface Settings. Figure 43. WAN Circuit Configuration page, Line Interface Settings Configuring the T1 line settings 1.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation 2. From the Line Coding pull-down menu (figure 45), select dsx1B8ZS(2) or dsx1AMI(5). Figure 45. Line Coding pull-down menu with dsx1B8ZS(2) selected 3. From the Line Build Out pull-down menu (figure 46) select t1pulse0dB(1). Figure 46. Line Build Out pull-down menu with t1pulse0dB(1) selected 4. Click on Submit Query to apply your settings. At this point the WAN front panel LEDs will become active.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation Saving your configuration At this point you have completed the basic configuration of your T-DAC for operation. To save your configuration settings in non-volatile RAM, do the following: 1. On the Configuration Menu click the Select HOME hyperlink to open the 3196RC Configuration Menu home page (figure 48). Figure 48. 3196RC Configuration Menu home page 2. Click the Record Current Configuration button (see figure 48).
Model 3196RC T-DAC User Manual Note 3 • Configuring the T-DAC for operation The parameters that will be exported are the power-up settings as they are stored in flash memory and may not be the current operating parameters. To ensure that you export the most current parameters, go to HOME, then under Immediate Actions, click on the Record Current Configuration button. To import or export a configuration, do the following: 1.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation Backing up the configuration store in flash memory 1. To make a back-up copy of the configuration file currently stored in your T-DAC’s flash memory: – On the Import/Export page (figure 50) click the Export Flash... hyperlink. The T-DAC will get the configuration file currently stored in your T-DAC’s flash memory and display it in your browser (figure 50) Figure 50.
Model 3196RC T-DAC User Manual 3 • Configuring the T-DAC for operation – To save the displayed data as a text file, use your browser’s Save function (figure 51). Using Netscape or Internet Explorer, for example. • Click the File menu. • Click Save As. A dialog box will appear. Use the dialog to save the data displayed on your browser (your T-DAC configuration parameters) to a text file. • Select the folder in which you want to store the file. • Type a file name. • Click Save. Figure 51.
Model 3196RC T-DAC User Manual Note 3 • Configuring the T-DAC for operation If the T-DAC does not behave as described, the most likely cause is that the T-DAC default settings are not compatible with the T1/E1 line. If this is the case, use the RS-232 CONFIG port to correct the T-DAC settings. You will have to use the 3196RC Configuration Menu pages to examine the configured T1/E1 link settings. 6.
Chapter 4 Operation and shutdown Chapter contents Introduction ..........................................................................................................................................................69 Activating the Model 3196RC...............................................................................................................................69 De-activating the Model 3196RC ......................................................................................................
Model 3196RC T-DAC User Manual 4 • Operation and shutdown Introduction This chapter describes how to start up and power down the Model 3196RC. Activating the Model 3196RC The Model 3196RC is activated by completing the procedures in chapter 2, “Hardware installation” on page 24 and chapter 3, “Configuring the T-DAC for operation” on page 35. To activate the 3196RC, follow the procedures in those chapters. The Model 3196RC is designed for unattended operation.
Chapter 5 Troubleshooting and maintenance Chapter contents Introduction ..........................................................................................................................................................71 Fault analysis .........................................................................................................................................................72 Basic iDSL and T1/E1 test modes ..............................................................................
Model 3196RC T-DAC User Manual 5 • Troubleshooting and maintenance Introduction This chapter describes troubleshooting and fault analysis that can be performed by the operator. If you require more help, refer to chapter 6, “Contacting Patton for assistance” on page 85. Refer to table 7 for a list of common symptoms and suggested remedies.
Model 3196RC T-DAC User Manual 5 • Troubleshooting and maintenance Fault analysis The following procedures outline steps you should follow when troubleshooting a Model 3196RC malfunction. 1. If possible, talk to the person who filed the trouble complaint and determine the operational symptoms. Record the symptoms on the appropriate trouble report form (include the front panel LED indications). 2.
Model 3196RC T-DAC User Manual 5 • Troubleshooting and maintenance Table 8. LED definitions (Continued) LED SYSTEM ETHERNET Location Front panel Front panel Color Green Status Meaning Flashing The Model 3196RC is operating normally. No action recommended. Off The Model 3196RC is not functioning properly. As soon as possible, unplug both power cables from the Model 3196RC, wait 30 seconds, then plug the cables back into the Mode 3196RC to see if the problem disappears.
Model 3196RC T-DAC User Manual 5 • Troubleshooting and maintenance Table 8. LED definitions (Continued) LED WANa Location Color Status Front Panel Green On solid Indicates normal activity at each of the T1/E1/PRI links. No action recommended. Single Flash Meaning Indicates that the Model 3196RC is detecting the network, but is unable to synchronize with it. Double Indicates an error on any of the T1/E1/PRI links.
Model 3196RC T-DAC User Manual 5 • Troubleshooting and maintenance T1/E1 port 1 DSL port 3196RC Figure 52. Local loopback To select local loop go to the iDSL page and find the port to be placed under loopback. Locate the Test Mode drop down menu and select local Loop(1). Go to the bottom of the screen and click on the Submit button. To turn off the loop mode, use the Test Mode drop down menu, select “Off” and click on the Submit button.
Model 3196RC T-DAC User Manual 5 • Troubleshooting and maintenance To activate remote loop, do the following: 1. Go to the iDSL page and find the port to be placed under loopback. 2. Locate the Test Mode drop down menu and select remoteLoop(2). 3. Go to the bottom of the screen and click on the Submit button. the DSL port selected for remote loop will be highlighted in blue. To deactivate the loop mode, use the Test Mode drop down menu, select none(0) and click on the Submit button.
Model 3196RC T-DAC User Manual 5 • Troubleshooting and maintenance T1/E1 port test modes The 3196RC offers a number of diagnostics tools to test operation and performance of the T1/E1 ports and line. Diagnostics include DSX1 payload loop and DSX1 line loop. DSX1 payload loop (dsx1PayloadLoop) When activated, the received signal at the selected T1/E1 port, will be looped through the 3196RC (see figure 55).
Model 3196RC T-DAC User Manual 5 • Troubleshooting and maintenance DSX1 line loop (dsxLineLoop) When activated, data received at the selected T1/E1 port, is looped back to the originating device (see figure 56). Data is looped at the T1/E1 port. T1/E1 port 3196RC Figure 56. Line Loop To activate line loop, do the following: 1. Click on the Modify Configuration link of the T1/E1 port to be placed under test. 2. Locate the Loopback Configuration drop down menu 3.
Model 3196RC T-DAC User Manual 5 • Troubleshooting and maintenance Maintenance This section describes replacing the Model 3196RC. Replacing the Model 3196RC If you isolate a problem to the a Model 3196RC component, the entire Model 3196RC must be replaced as follows. Exporting the current Model 3196RC configuration The 3196RC T-DAC provides Import/Export functions. These functions enable you to back up (export) and restore (import) your T-DAC’s configuration parameters against possible failure.
Model 3196RC T-DAC User Manual 5 • Troubleshooting and maintenance 2. On the Configuration Menu pane, click the Import/Export hyperlink to display the Import/Export page (figure 57). Figure 57.
Model 3196RC T-DAC User Manual 5 • Troubleshooting and maintenance 3. To make a back-up copy of the configuration file currently stored in your T-DAC’s flash memory: – On the Import/Export page (figure 57 on page 80) click the Export Flash... hyperlink. The T-DAC will get the configuration file currently stored in your T-DAC’s flash memory and display it in your browser (see figure 58) Figure 58.
Model 3196RC T-DAC User Manual 5 • Troubleshooting and maintenance – To save the displayed data as a text file, use your browser’s Save function (see figure 59). Using Netscape or Internet Explorer, for example. • Click the File menu. • Click Save As. A dialog box will appear. Use the dialog to save the data displayed on your browser (your T-DAC configuration parameters) to a text file. • Select the folder in which you want to store the file, • Type a file name. • Click Save. Figure 59.
Model 3196RC T-DAC User Manual 5 • Troubleshooting and maintenance 3. Unlock the handles by pressing the red button on each handle. The button immediately activates the switch (turning it to an open position), while the button itself remains depressed. The blade can then be removed. 4. Remove the malfunctioning Model 3196RC by pushing the handles outwards, pulling the card gently but firmly from its slot in the chassis.
Model 3196RC T-DAC User Manual 5 • Troubleshooting and maintenance Completing the installation This section verifies that the Model 3196RC is fully operational. 1. Verify that the green POWER LED is lit. If the POWER LED is flashing green, refer to section “Fault analysis” on page 72. 2. Verify that the WAN LED illuminates, indicating that the Model 3196RC is synchronizing with the T1/E1 signal. 3.
Chapter 6 Contacting Patton for assistance Chapter contents Introduction ..........................................................................................................................................................86 Contact information..............................................................................................................................................86 Warranty Service and Returned Merchandise Authorizations (RMAs).....................................................
Model 3196RC T-DAC User Manual 6 • Contacting Patton for assistance Introduction This chapter contains the following information: • “Contact information”—describes how to contact Patton technical support for assistance. • “Warranty Service and Returned Merchandise Authorizations (RMAs)”—contains information about the RAS warranty and obtaining a return merchandise authorization (RMA). Contact information Patton Electronics offers a wide array of free technical services.
Model 3196RC T-DAC User Manual 6 • Contacting Patton for assistance Return for credit policy • Less than 30 days: No Charge. Your credit will be issued upon receipt and inspection of the equipment. • 30 to 120 days: We will add a 20% restocking charge (crediting your account with 80% of the purchase price). • Over 120 days: Products will be accepted for repairs only. RMA numbers RMA numbers are required for all product returns.
Appendix A Network Ports (RJ-21X) connector pin-out Chapter contents Introduction ..........................................................................................................................................................
Model 3196RC T-DAC User Manual A • Network Ports (RJ-21X) connector pin-out Introduction Figure 60 shows the pin-out for the RJ-21X 50-pin Telco connector. Table 9 contains the band-marked color codes for the RJ-21X 50-pin Telco connector Pin 1 25 50-pin TELCO Male 26 50 Figure 60. 50-pin Telco connector Table 9.
Model 3196RC T-DAC User Manual A • Network Ports (RJ-21X) connector pin-out Table 9.
Appendix B WAN Network Module connector pinout Chapter contents Introduction ..........................................................................................................................................................92 68-Pin Telco pinout ..............................................................................................................................................
Model 3196RC T-DAC User Manual B • WAN Network Module Introduction The WAN cable is 6 feet in length comprising 34 twisted pairs. One end of the cable will have the AMP connector 749621-7 (or equivalent) and the AMP back shell 749195-2 (or equivalent). The other end will be blunt. AMP 749621-7 (or equivalent) Pin 1 34 35 68 Figure 61.
Model 3196RC T-DAC User Manual B • WAN Network Module Table 10.
