Model 3095 mDSL Digital Access and Cross-Connect System (DACS) Getting Started Guide Sales Office: +1 (301) 975-1000 Technical Support: +1 (301) 975-1007 E-mail: support@patton.com WWW: www.patton.com Document Number: 110061U Rev.
Patton Electronics Company, Inc. 7622 Rickenbacker Drive Gaithersburg, MD 20879 USA tel: +1 (301) 975-1000 fax: +1 (301) 869-9293 support: +1 (301) 975-1007 web: www.patton.com e-mail: support@patton.com Copyright © 2001 & 2002, Patton Electronics Company. All rights reserved. The information in this document is subject to change without notice. Patton Electronics assumes no liability for errors that may appear in this document.
Contents Contents ......................................................................................................................................................... 3 Compliance Information ................................................................................................................................ 7 Radio and TV Interference ...............................................................................................................................7 Industry Canada Notice ......
Contents Model 3095 mDSL DACS Getting Started Guide Connecting the Ethernet ports ........................................................................................................................26 Connecting the 10/100Base-T Ethernet port to an Ethernet switch or hub ...............................................26 Connecting the 10/100Base-T Ethernet port to an Ethernet-capable workstation or PC .................................
Model 3095 mDSL DACS Getting Started Guide Contents Using the DB9-RJ45 adapter with the included cable ...............................................................................60 Setting up the HyperTerminal (or similar program) session ......................................................................61 Completing the installation .......................................................................................................................64 6 Contacting PATTON for assistance .........
Contents 6 Model 3095 mDSL DACS Getting Started Guide
Compliance Information Radio and TV Interference The Model 3095 generates and uses radio frequency energy, and if not installed and used properly—that is, in strict accordance with the manufacturer's instructions—may cause interference to radio and television reception.
Model 3095 mDSL DACS Getting Started Guide you must notify the telephone company prior to disconnection. The following information may be required when applying to your local telephone company for leased line facilities. The Universal Service Order Code (USOC) is RJ48. The Facility Interface Codes (FIC) are 04DU9-BN, 04DU9-DN, 04DU9-1KN, and 04DU9-1SN. The Service Order Code (SOC) is 6.0N. Service Facility Service Network Interface Code Code Connection 04DU9-BN 6.0N RJ-48C 1.
About this guide This guide describes installing and configuring a Patton Electronics Model 3095 mDSL Digital Access and Cross-Connect System (DACS). By the time you are finished with this guide, your DACS will be connected to the remote DSL modems and transferring data.
Model 3095 mDSL DACS Getting Started Guide Precautions Notes and cautions, which have the following meanings, are used throughout this guide to help you become aware of potential DACS problems. Warnings relate to personal injury issues, and Cautions refer to potential property damage. Note Calls attention to important information. The shock hazard symbol and WARNING heading indicate a potential electric shock hazard. Strictly follow the warning instructions to avoid injury caused by electric shock.
Model 3095 mDSL DACS Getting Started Guide Mouse conventions The following conventions are used when describing mouse actions: Table 2. Mouse conventions Convention Meaning Left mouse button This button refers to the primary or leftmost mouse button (unless you have changed the default configuration). Right mouse button This button refers the secondary or rightmost mouse button (unless you have changed the default configuration).
Model 3095 mDSL DACS Getting Started Guide 12
Chapter 1 Introduction Chapter contents Model 3095 mDSL DACS overview .....................................................................................................................14 Hardware overview ................................................................................................................................................15 WAN .......................................................................................................................................................
1 • Introduction Model 3095 mDSL DACS Getting Started Guide Model 3095 mDSL DACS overview The Model 3095 links up 16 mDSL circuits to multiple WAN uplink modules with completely flexible grooming. The DACs combines dual-redundant power supplies, a time-slot multiplexer, and a centralized management system into an ultra-sleek 1U chassis. The subscriber side connects to compatible mDSL modems for data rates up to 2.3 Mbps service over a single pair.
Model 3095 mDSL DACS Getting Started Guide 1 • Introduction Hardware overview The Model 3095 combines transmission and networking technology concentrating 16 mDSL ports and four to sixteen T1/E1 WAN links into a single 1U managed chassis. The DACS (see figure 2) comprises a 1U-high 19-inch wide chassis that contains a motherboard and two dual-redundant power supplies.
1 • Introduction Model 3095 mDSL DACS Getting Started Guide • Auto detection and fallback • 10/100 Mbps link and status indicators RS-232 control port The RS-232 port provides for initial configuration of the Model 3095. The RS-232 port supports: • Asynchronous data rates of 19.2 kbps, 8 data bits, no parity, 1 stop bit.
Model 3095 mDSL DACS Getting Started Guide 1 • Introduction • 3-pin terminal block connector • 3-contact dry relay for external alarm systems System Timing and Clock Port The mDSL Multiplexer's system timing may be derived from the external reference Clock Port, an Internal Clock from an on-board chip, a CPE mDSL modem, or a Network Clock from one of the T1/E1 WAN ports. The system timing is configured through the NMS.
1 • Introduction Model 3095 mDSL DACS Getting Started Guide 11.75 in. (29.85 cm) Top View UNIT EQUIPPED WITH DUAL SUPPLIES DISCONNECT BOTH SUPPLIES BEFORE SERVICING 1.75 in. (1U) (4.44 cm) UNIT EQUIPPED WITH DUAL SUPPLIES DISCONNECT BOTH SUPPLIES BEFORE SERVICING 10/100 RS-232 ETHERNET CONFIG Rear View 1 ALARM 90-264V (50-60 Hz) 2 AMP WAN EGRESS MODULE PORT EXT CLOCK 2.3 Mbps m DSL MODEM PORTS 90-264V (50-60 Hz) 2 AMP 26 17 in. (43 cm) Figure 3.
Model 3095 mDSL DACS Getting Started Guide 1 • Introduction EQ SC UI PP ON ED BE NE FO CT WIT RE BO H DU SE TH RV SU AL IC PP SU PP IN G LIE LIE S IT DI UN S 60 er 29Serv ELcess OotDe Ac Mm Re EQ SC UI PP ON ED BE NE FO CT WIT RE BO H DU SE TH RV SU AL IC PP SU PP IN G LIE LIE S IT DI UN S FR WA N PO RTS ER EXP enabled LED E AM R RO 4 3 T AC T NO SIG AC CA S ET LL RN CA EM HE ET ST M SY AR IL AL FA R U WE DSL enabled LED CP PO LL NA L 2 1 POWER LED ALARM LED C
1 • Introduction Model 3095 mDSL DACS Getting Started Guide • EXP PORTS: Green indicates normal activity on DSO expansion board. Red indicates loss of sync on any DSL port. • WAN PORTS: Green indicates normal activity for each T1/E1 link. Red indicates an error on the port (e.g., loss of sync, etc.).
Chapter 2 Hardware installation Chapter contents Introduction ..........................................................................................................................................................22 Unpacking the Model 3095 DACS .......................................................................................................................22 DACS chassis installation .................................................................................................................
2 • Hardware installation Model 3095 mDSL DACS Getting Started Guide Introduction This chapter contains the following procedures for installing the Model 3095 DACS: Note Before installing the DACS, you will need to obtain the line type and encoding of the T1/E1 line from your local telephone company (telco).
Model 3095 mDSL DACS Getting Started Guide 2 • Hardware installation 4. Place the DACS at the desired position in the rack. 5. Secure the DACS in position with the mounting screws. Cable installation This section describes installing the power, ground, and network interface cables. Installing the power cables—AC Power Supply This section describes installing the power cables into the IEC-320 connectors on the DACS. Do not connect the male end of the power cables to the power outlet at this time.
2 • Hardware installation Model 3095 mDSL DACS Getting Started Guide 2. Rotate the power cable retainer clip so it secures the power cable plug in the IEC-320 connector as shown in figure 6. Figure 6. Power cable retainer clip 3. Repeat steps 1 and 2 to install the remaining power cable. Installing the power cables—DC Power Supply This section describes installing the DACS for using DC power. Do not connect the remaining end of the power cables to the DC power source.
Model 3095 mDSL DACS Getting Started Guide 2 • Hardware installation G N IT E D Q IS U C IP O P N E B N D E E W F C I O T T R B H E O D S T U E H A R S L V U S IC P U IN P P G LIE PL S IES I NF CO U T NE 0E /10 10 Grounding stud V 64 ) -2 Hz 90-60 P 0 (5 AM 2 - DC input + DC input Figure 7. DC connector, - DC and + DC Input view 4. Repeat steps 1 through 3 to install the remaining DC power connection. Grounding the Model 3095—AC and DC Power Supplies Do the following: 1.
2 • Hardware installation Model 3095 mDSL DACS Getting Started Guide Connecting the Ethernet ports The DACS has a single 10/100 Ethernet interface for connection to your LAN (see figure 8). The Ethernet port will autosense the correct speed of the local LAN and automatically negotiate half- or full-duplex operation. This section describes connecting the DACS to the Ethernet LAN via an Ethernet hub, switch, or workstation.
Model 3095 mDSL DACS Getting Started Guide 2 • Hardware installation Connecting the 10/100Base-T Ethernet port to an Ethernet-capable workstation or PC The 10/100Base-T Ethernet port can connect to a single Ethernet-capable workstation or PC by means of a cross-over cable. Refer to figure 10 to assemble a cross-connect cable that will connect between the NIC Ethernet port in the workstation and the DACS 10/100Base-T Ethernet port. Figure 10.
2 • Hardware installation Model 3095 mDSL DACS Getting Started Guide 2. The other end of the cable has 68 unterminated twisted-pairs for connection to a punch-down block. Select the twisted pairs for the WAN ports that will be activated and terminate them on the punch-down block. Connecting the mDSL Ports The remote (CPE) mDSL modems are connected to the DACS via the RJ-21X cable.
Model 3095 mDSL DACS Getting Started Guide 2 • Hardware installation 1. Connect the equipment to a 40–72 VDC, 2.5A supply source that is electrically isolated from the AC source. The 40–72 VDC source is to be reliably connected to earth. 2. Verify that the green POWER LED is lit. If the POWER LED is flashing green, refer to Chapter 5, “Troubleshooting and maintenance”. Hardware installation is complete. Refer to Chapter 3, “Configuring the DACS for operation”.
2 • Hardware installation 30 Model 3095 mDSL DACS Getting Started Guide Completing the hardware installation
Chapter 3 Configuring the DACS for operation Chapter contents Introduction ..........................................................................................................................................................32 Configuration prerequisites ...................................................................................................................................32 Initial Configuration through the RS-232 Control Port ................................................................
3 • Configuring the DACS for operation Model 3095 mDSL DACS Getting Started Guide Introduction This chapter contains the following procedures for configuring the Model 3095 DACS for operation: • “Configuration prerequisites”—lists the items you need to have on hand before configuring the DACS. • “Initial Configuration through the RS-232 Control Port” on page 33—describes setting up the 3095’s LAN IP address and netmask parameters.
Model 3095 mDSL DACS Getting Started Guide 3 • Configuring the DACS for operation • If you are using a E1 WAN line, you will need the following information from the telco: - Line Type: either E1 or E1-CRC - Line Coding: either HDB3 or AMI Initial Configuration through the RS-232 Control Port Initially you must configure the 3095’s IP address and—in rare instances—change the netmask from the default settings. Note Do not connect power or the Ethernet connection to the Model 3095 at this time.
3 • Configuring the DACS for operation Model 3095 mDSL DACS Getting Started Guide Figure 13. Connect To window 3. On the Connect To window (see figure 13), set Connect using: to one of the options named Direct to ComX (where the "X" refers to the number identifying the RS-232 serial port on the PC). In the following procedure, Com1 will be the used as the port identifier. 4. Click on OK. 5. The COM1 Properties window displays. 6. Configure your COM port settings as shown in figure 14, then click OK.
Model 3095 mDSL DACS Getting Started Guide 3 • Configuring the DACS for operation 8. Configure the settings for Function, arrow and ctrl keys act as to Terminal keys as shown in figure 15, then click OK. Figure 15. Terminal keys configuration 9. Connect the male end of the 3095 DACS’ power cables to the power outlets. 10. On your HyperTerminal connection window, boot up information will display, eventually followed by a login request window resembling that shown in figure 16. Figure 16.
3 • Configuring the DACS for operation Model 3095 mDSL DACS Getting Started Guide Figure 17. VT-100 Top Level Management window 13. Type k for System, then press . 14. Under System, type 1 for Details, then press . 15. Enter g for LAN Address, then press . 16. Type your LAN IP address followed by pressing . 17. Press the left-arrow cursor key on your keyboard to return to the previous screen. 18. If you do not need to change the LAN Mask from the default of 255.255.255.
Model 3095 mDSL DACS Getting Started Guide 3 • Configuring the DACS for operation • Configuring the IP default gateway (see “Configuring the default gateway” on page 44) • Configuring the T1/E1 WAN links (see “Configuring line settings and signaling for E1” on page 45 or “Configuring line settings and signaling for T1” on page 46) Displaying the DACS 3095 Web Administration Pages Do the following: 1. Connect your PCs Ethernet connection to the Ethernet. 2.
3 • Configuring the DACS for operation Model 3095 mDSL DACS Getting Started Guide system page you may select, the Configuration/information pane contents will change as you move from one subsystem page to another. Configuration Menu pane Configuration/information pane Figure 19. HOME page window panes Figure 20.
Model 3095 mDSL DACS Getting Started Guide 3 • Configuring the DACS for operation 3095 configuration are stored in volatile DRAM first, enabling the user to set the box up with a working configuration before committing it to storage in FLASH. The configuration changes become permanent when you select Record Current Configuration.
3 • Configuring the DACS for operation Model 3095 mDSL DACS Getting Started Guide two mDSL modems, or (3) between WAN time slots. Without defining the mapping, the modems have no destination; similarly with the WAN ports. The DACS functions like a 2-dimensional matrix switch. Do the following to set the DS0 Mapping of the mDSL modems: 1. Click on DS0 Mapping on the Configuration Menu. 2. Set the DS0 Display Type (see figure 21) to displayLongForm(0).
Model 3095 mDSL DACS Getting Started Guide 3 • Configuring the DACS for operation Examples on configuring static connections. Example 1 Connect mDSL modem, Port 3 (referring to modem #3), time slots 1 - 31, to an E1 line on (WAN) Port 1, time slots 1 - 31. Solution: Complete the following steps. 1. Under "Dev Type A," select mDSL(3). 2. Under "Dev Num A," select port3(3). 3. Under "Dev Slots A," enter 1 - 31. 4. Under "Dev Type B," select t1-e1(1). 5. Under "Dev Num B," select port1(1). 6.
3 • Configuring the DACS for operation Model 3095 mDSL DACS Getting Started Guide 7. Click on the "Submit Query" button located to the right of the static connection entry you just completed. Example 3 Connect two mDSL modems together - mDSL modem #15, time slots 1 - 32 (for a DTE data rate of 2.048 Mbps) to mDSL modem #16, time slots 1 - 32. Solution: Complete the following steps. 1. Under "Dev Type A," select mDSL(3). 2. Under "Dev Num A," select port15(15). 3. Under "Dev Slots A," enter 1 - 32. 4.
Model 3095 mDSL DACS Getting Started Guide 3 • Configuring the DACS for operation Figure 22. System Clocking Configuration window 3. Set the Fallback Reference to internal(200) if you have no other T1/E1 Wan links for connection to the 3095. Otherwise select the appropriate Wan port under Fallback Reference. 4. Click on Submit Query. \ Figure 23. mDSO Port Configuration window Activating the mDSL modems Before data transmission can occur, the internal mDSL modems must be activated.
3 • Configuring the DACS for operation Note Model 3095 mDSL DACS Getting Started Guide Both Submit Query buttons on this page fulfill the same function. You do not need to click Submit Query if you chose Activate All Available Ports or any of the Activate Port. Configuring the default gateway Do the following to add the default gateway: 1. Select IP on the Configuration Menu, then click on Routing Info (see figure 24). Figure 24. IP Routing Information window 2.
Model 3095 mDSL DACS Getting Started Guide 3 • Configuring the DACS for operation Figure 25. T1/E1 Link Activity window Configuring line settings and signaling for E1 1. Select T1/E1 Link on the Configuration Menu. The T1/E1 Link Activity Overview window appears (see figure 25).
3 • Configuring the DACS for operation Model 3095 mDSL DACS Getting Started Guide 2. View Link 1 corresponds to the first Wan circuit on the DACS. Beside View Link 1-4 click on View Links, Configuration then Modify. The Line Interface Settings of the WAN Circuit Configuration window appears (see figure 26). Figure 26. WAN Circuit Configuration window, Line Interface Settings section Configuring the E1 line settings 1.
Model 3095 mDSL DACS Getting Started Guide 3 • Configuring the DACS for operation Configuring the line settings 1. Click on the Line Type pull-down menu (see figure 26 on page 46) and choose from the following options: - dsx1ESF Extended SuperFrame DS1 - dsx1D4 AT&T D4 format DS1 2. Click on the Line Coding pull-down menu (see figure 26 on page 46). The most common options are dsx1B8ZS and dsx1AMI. 3. Click on the Line Build Out pull-down menu (see figure 26 on page 46) and select t1pulse0dB(1). 4.
3 • Configuring the DACS for operation Model 3095 mDSL DACS Getting Started Guide Figure 27. Import/Export main window 5. To export the flash configuration, click on the Export Flash link on the Import/Export main page. The access server will display text configuration information resembling that shown in figure 28. Figure 28. Typical access server flash memory configuration data To save the displayed data as a text file, select the Save option on your browser (see figure 29).
Model 3095 mDSL DACS Getting Started Guide 3 • Configuring the DACS for operation export parameters to a text file. Select the location where you want the file stored, type a file name, and click Save. Figure 29. Saving the access server flash memory configuration data as a text file Completing the installation This section verifies that the Model 3095 is fully operational. 1. Temporarily disconnect the male ends of both power cords from the power outlet.
3 • Configuring the DACS for operation Model 3095 mDSL DACS Getting Started Guide 6. There are two LEDs on the DACS 10/100 Ethernet port: a green LED that indicates link status and activity, and a yellow LED that indicates line speed. Verify that the green LED is either flashing green (meaning that packets are being received at the Ethernet port) or solid green (meaning that the link is valid but no packets are being received). Congratulations! Your DACS is now installed.
Chapter 4 Operation and shutdown Chapter contents Introduction ..........................................................................................................................................................52 Activating the Model 3095 ....................................................................................................................................52 De-activating the Model 3095.....................................................................................................
4 • Operation and shutdown Model 3095 mDSL DACS Getting Started Guide Introduction This chapter describes how to start or power-down the Model 3095. Activating the Model 3095 Once the Model 3095 has been installed, no operator action is required under normal conditions; the Model 3095 is designed for unattended operation. The Model 3095 does not have a power switch and powers up immediately upon connecting the power cords to the 3095.
Chapter 5 Troubleshooting and maintenance Chapter contents Introduction ..........................................................................................................................................................54 Fault analysis .........................................................................................................................................................55 Periodic maintenance .........................................................................................
5 • Troubleshooting and maintenance Model 3095 mDSL DACS Getting Started Guide Introduction This chapter describes troubleshooting and fault analysis that can be performed by the operator. If you require more help, refer to Chapter 6, “Contacting PATTON for assistance”. Refer to table 3 for a list of common symptoms and suggested remedies.
Model 3095 mDSL DACS Getting Started Guide 5 • Troubleshooting and maintenance Fault analysis The following procedures outline steps you should follow when troubleshooting a Model 3095 malfunction. 1. If possible, talk to the person who filed the trouble complaint and determine the operational symptoms. Record the symptoms on the appropriate trouble report form (include the front panel LED indications). 2.
5 • Troubleshooting and maintenance Model 3095 mDSL DACS Getting Started Guide Table 4. LED definitions LED ETHERNET Location Color Status Meaning Front panel Green On solid Link status is nominal for the Ethernet port. No action recommended. Off • A valid link has not been detected. • Verify that the cable is plugged into the hub, switch, or workstation and the Model 3095. • Verify that the hub, switch, or workstation is powered on. • Verify that the correct cable is being used.
Model 3095 mDSL DACS Getting Started Guide 5 • Troubleshooting and maintenance Table 4. LED definitions LED 10/100 ETHERNET Location Color Status Rear panel Meaning Green On solid Link is valid. No action recommended. Off • A valid link has not been detected. • Verify that the cable is plugged into the hub, switch, or workstation and the Model 3095. • Verify that the hub, switch, or workstation is powered on. • Verify that the correct cable is being used.
5 • Troubleshooting and maintenance Model 3095 mDSL DACS Getting Started Guide 2. To export a configuration, connect your Web browser to the Administration Pages, then click on Import/ Export under the Configuration Menu to display the Import/Export main window (see figure 30). Figure 30. Import/Export main window Note The parameters that will be exported are the power-up settings as they are stored in flash memory and may not be the current operating parameters.
Model 3095 mDSL DACS Getting Started Guide 5 • Troubleshooting and maintenance Figure 31. Typical access server flash memory configuration data 4. To save the displayed data as a text file, select the Save option on your browser (see figure 32). For example, under Netscape, select File > Save As. A dialog box will display enabling you to save the contents of the export parameters to a text file. Select the location where you want the file stored, type a file name, and click Save. Figure 32.
5 • Troubleshooting and maintenance Model 3095 mDSL DACS Getting Started Guide 2. Unplug both male power cable connectors from their outlets. 3. Rotate the power cord retainer clips out of the way, then remove both power cables from the malfunctioning Model 3095. 4. Disconnect and label the following cables from the malfunctioning Model 3095: – the T1/E1 WAN cables – the RS-232 CONFIG cable – the 10/100 ETHERNET cable 5. Disconnect the ground wire from the grounding stud. 6.
Model 3095 mDSL DACS Getting Started Guide 5 • Troubleshooting and maintenance 2. Connect the RJ45-RJ45 cable between the adapter you installed in step 1 and the RS-232 Config port on the rear of the Model 3095. Setting up the HyperTerminal (or similar program) session Do the following: 1. Open a HyperTerminal session by double-clicking on HYPERTRM.EXE. Figure 33. Connection Description window 2. Type a connection name (for example, 3095 Config), select an icon, then click OK (see figure 33).
5 • Troubleshooting and maintenance Model 3095 mDSL DACS Getting Started Guide 6. Configure your COM port settings as shown in figure 35, then click OK. Figure 35. COM1 Properties window 7. Click on the File menu, then select Properties. 8. Configure the settings for Function, arrow and ctrl keys act as to Terminal keys as shown in figure 36, then click OK. Figure 36.
Model 3095 mDSL DACS Getting Started Guide 5 • Troubleshooting and maintenance 9. Connect the male end of the 3095 DACS power cables to the power outlets. 10. On your HyperTerminal connection window, boot up information will display, eventually followed by a login request window resembling that shown in figure 37. Figure 37. Login window 11. For the user name, type superuser. 12. For the password, type superuser; the TOP LEVEL MANAGEMENT window then appears (see figure 38). Figure 38.
5 • Troubleshooting and maintenance Model 3095 mDSL DACS Getting Started Guide 20. Select a for Home, then press . 21. Under the Current Status page, type 1 (storeConfig(1))to save the changes you have just made to the configuration. 22. To import a saved configuration, connect your Web browser to the Administration Pages, then click on Import/Export under the Configuration Menu to display the Import/Export main window (see figure 30 on page 58). 23.
Chapter 6 Contacting PATTON for assistance Chapter contents Introduction ..........................................................................................................................................................66 Contact information..............................................................................................................................................66 Warranty Service and Returned Merchandise Authorizations (RMAs).....................................................
6 • Contacting PATTON for assistance Model 3095 mDSL DACS Getting Started Guide Introduction This chapter contains the following information: • “Contact information”—describes how to contact PATTON technical support for assistance. • “Warranty Service and Returned Merchandise Authorizations (RMAs)”—contains information about the RAS warranty and obtaining a return merchandise authorization (RMA). Contact information Patton Electronics offers a wide array of free technical services.
Model 3095 mDSL DACS Getting Started Guide 6 • Contacting PATTON for assistance Return for credit policy • Less than 30 days: No Charge. Your credit will be issued upon receipt and inspection of the equipment. • 30 to 60 days: We will add a 20% restocking charge (crediting your account with 80% of the purchase price). • Over 60 days: Products will be accepted for repairs only. RMA numbers RMA numbers are required for all product returns.
6 • Contacting PATTON for assistance 68 Model 3095 mDSL DACS Getting Started Guide Warranty Service and Returned Merchandise Authorizations (RMAs)
Appendix A ‘Network Ports (RJ-21X) connector pin-out Chapter contents Introduction ..........................................................................................................................................................
A • ‘Network Ports (RJ-21X) connector pin-out Model 3095 mDSL DACS Getting Started Guide Introduction Table 5 contains the band-marked color codes for the RJ-21X, 50-pin Telco connector. The Pair Number matches the port number on the DS0 Mapping Management page. 25 50 1 NETWORK PORTS 26 Figure 39. 50-pin Teleco connector Table 5.
Model 3095 mDSL DACS Getting Started Guide A • ‘Network Ports (RJ-21X) connector pin-out Table 5.
A • ‘Network Ports (RJ-21X) connector pin-out 72 Model 3095 mDSL DACS Getting Started Guide Introduction
Appendix B WAN Network Module connector pin-out Chapter contents Introduction ..........................................................................................................................................................
B • WAN Network Module connector pin-out Model 3095 mDSL DACS Getting Started Guide Introduction Table 6 and Table 7 contain the pin-out information for the 68-pin SCSI connector. 1 35 34 WAN NETWORK MODULE 68 Figure 40.
Model 3095 mDSL DACS Getting Started Guide B • WAN Network Module connector pin-out Table 6.
B • WAN Network Module connector pin-out Table 7.
