USER MANUAL MODEL 2173R Ruggedized High Speed Ethernet Extender Part# 07M2173R-UM Rev.
CONTENTS 1.0 1.1 1.2 1.3 1.4 1.5 1.6 Warranty Information ................................................................. Compliance................................................................................... EMC Compliance:......................................................................... Low-Voltage Direcive (Safety): ..................................................... PSTN: ...........................................................................................
RJ-45 .......................................................................................... 18 C.2 CopperLINK Interface ................................................................ 18 RJ-45 .......................................................................................... 18 D Sample Rates/Distance Chart, Based on 24 AWG (0.5 MM) .
1.0 WARRANTY INFORMATION Patton Electronics warrants all Model 2173R components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of the shipment. This warranty is limited to defects in workmanship or materials, and does not cover customer damage, abuse or unauthorized modification. If this product fails or does not performs as warranted, your sole recourse shall be repair or replacement as described above.
reception. This equipment has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable protection from such interference in a commercial installation. However, there is no guarantee that interference will not occur in a particular installation.
1.6 SAFETY WHEN WORKING WITH ELECTRICITY • This device contains no user serviceable parts. This device can only be repaired by qualified service personnel. • Do not open the device when the power cord is connected. For systems without a power switch and without an external power adapter, line voltages are present within the device when the power cord is connected. • For devices with an external power adapter, the power adapter shall be a listed Limited Power Source.
In accordance with the requirements of council directive 2002/96/EC on Waste of Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate this product from other waste and scrap and deliver to the WEEE collection system in your country for recycling. WARNING WARNING This device is NOT intended nor approved for connection to the PSTN. It is intended only for connection to customer premise equipment.
2.0 GENERAL INFORMATION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for one year for parts and labor. If any questions or problems arise during installation or use of this product, contact Patton Electronics Technical Support at +1 (301) 975-1007. 2.
Figure 1. Typical application The pair of 2173R and 2173 models work together to create a transparent extension between two peered Ethernet LANs. Figure 1 shows a typical point-to-point application. 3.0 INSTALLATION CAUTION The Interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to voltage, current, anticipated temperature, flammability, and mechanical serviceability. To install the 2173R Ethernet Extender, do the following: 1.
Power Ethernet 1 Ethernet 2 Remote Local Link 2173R (RJ-45) R et 73 rn 21 the nk E rLi ized e d pp e Co ugg R Ex ten de r e Lin et ern Eth 2 er A PowV; 0.6 5 Power jack 1 CopperLINK twisted-pair RJ-45 interface Ethernet port 1 Ethernet port 2 Figure 2. Model 2173R panel 3.
2. The Model 2173R is equipped with either an RJ-45 interface jack that can be used on the CopperLINK interface. These CopperLINK interfaces are a two-wire interface. Observe the signal/pin relationships on the Model 2173R's CopperLINK interface jacks. The RJ-45 connector on the Model 2173R's twisted pair interface is polarity insensitive and is wired for a two-wire interface. The signal/pin relationship is shown in Figure 3.
1 TX+/RX+ 2 TX-/RX- 1 2 3 4 5 6 7 8 3 RX+/TX+ 4 (no connection) 5 (no connection) 6 RX-/TX7 (no connection) 8 (no connection) Figure 4. Model 2173R 10/100Base-T RJ-45 Connector Pinout. 3.3 CONNECTING POWER CAUTION The Interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to voltage, current, anticipated temperature, flammability, and mechanical serviceability.
r ed de pe ten h-S t Ex Higerne Eth Figure 5. Removing protective cover Figure 6 on page 13 shows the orientation of the DIP switches in the On and Off positions. Ruggedized High Speed Ethernet Extender S1 ON OFF S1 Switch toggle ON 1 2 Push toggle down for OFF position Figure 6.
4.2 CONFIGURING DIP SWITCH S1 DIP switch S1 is where you configure the CopperLINK line. The following tables describe the configuration for the 2173.
5.2 FRONT PANEL LED STATUS MONITORS The Model 2173R features six front panel LEDs that monitor power, the Ethernet signals, the CopperLINK connection, and the remote/local setting. Figure 7 shows the front panel location of each LED. Table 2 on page 15 describes the LED functions. er Power LED Link LED Ethernet 1 LED ne er ne er e th E ot l em ca R Lo E Local LED th t2 t1 Lin k P ow Ethernet 2 LED Remote LED en R t 73 rne 21the k in E rL ed pediz p e Cogg Ru de r t Ex r we Po0.
APPENDIX A SPECIFICATIONS A.1 LAN CONNECTION • Two shielded RJ-45, 10/100Base-T, IEEE 802.3 Ethernet • CopperLINK Connection: Shielded RJ-45 A.2 TRANSMISSION LINE Two-wire unconditioned twisted pair. A.3 COPPERLINK LINE RATE AND COPPERLINK DISTANCE • Line Rate: Up to 155 Mbps aggregate (upstream/downstream) via Auto Rate; and 25/25 Mbps via DIP switch settings. • Distance: Up to 5,500 ft (1.6 km) Note Distances depend on line rate and line conditions. A.
APPENDIX B MODEL 2173R FACTORY REPLACEMENT PARTS AND ACCESSORIES Patton Model # Description Base Models 2173R/E CopperLINK Multi Rate 100 Mbps Ethernet Extender; No power supply 2173R/E-2PK CopperLINK Multi Rate 100 Mbps Ethernet Extender Kit (2 units preset to local and remote); No power supply 2173R/EUI-2PK CopperLINK Multi Rate 100 Mbps Ethernet Extender Kit (2 units preset to local and remote); 110-240VAC 07M2173R-UM User Manual Power Supplies 08055DCUI 08055-120-5-1 100-240VAC (+5V reg.
APPENDIX C MODEL 2173R INTERFACE PIN ASSIGNMENT C.1 10/100BASE-T INTERFACE RJ-45 • Pin 1: TX+ • Pin 2: TX• Pin 3: RX+ • Pin 6: RX• Pins 4, 5, 7, 8: no connection C.
APPENDIX D SAMPLE RATES/DISTANCE CHART, BASED ON 24 AWG (0.5 MM) Rate Mode 4/1 Fast 4/1 Interleave 100/70 Fast 100/70 Interleave 25/25* Interleave 50/50 Fast 50/50 Interleave 70/70 Fast 70/70 Interleave Distance in Feet (km) Throughput at Max Distance (megabits per second) 5,500 (1.6 km) 5,500 (1.6 km) 500 ft (0.15 km) 250 (0.07 km) 2,250 (0.6 km) 1,750 (0.5 km) 1,750 (0.5 km) 1,750 (0.5 km) 1,750 (0.5 km) 4.00 (DS) 1.00 (US) 4.00 (DS) 1.00 (US) 83 (DS) 69.5 (US) 83 (DS) 69.
Copyright © 2011 Patton Electronics Company All Rights Reserved.
