USER MANUAL MODEL 2111 2-User Network Access Bridge Part# 07M2111-A Doc# 033071UA Revised 06/17/99 CERTIFIED An ISO-9001 Certified Company SALES OFFICE (301)975-1000 TECHNICAL SUPPORT (301)975-1007 http://www.patton.
TABLE OF CONTENTS SECTION 1.0 WARRANTY INFORMATION PAGE 1.0 Warranty Information..............................................................2 1.1 Radio and TV Interference 1.2. CE Notice 1.3 Service 2.0 General Information ...............................................................4 2.1 Features 2.2 Description 2.3 Typical Application 3.0 Installation ..............................................................................6 3.1 Connecting the Twisted Pair Line Interface 3.
2.0 GENERAL INFORMATION 1.3 SERVICE All warranty and non-warranty repairs must be returned freight prepaid and insured to Patton Electronics. All returns must have a Return Materials Authorization number on the outside of the shipping container. This number may be obtained from Patton Electronics Technical Service at: tel: (301)975-1007 email: support@patton.com www: http://www.patton.com Thank you for your purchase of this Patton Electronics product.
3.0 INSTALLATION 2.3 TYPICAL APPLICATION The 2111-CO and 2111-CP work together to create an extension between 2 peer Ethernet LANs with all the benefits of MAC bridging. The following diagram shows a typical application The Model 2111 requires no configuration. You only need to connect the Ethernet interface, line interface between the units and power. This section describes these connections.
3. Observe the Signal/Pin relationships on the Model 2111’s Line Interface jack. This Line Interface is a 2 wire interface. 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 3.2 CONNECTING THE 10BASET ETHERNET INTERFACE The RJ-45 jack labeled “Interface Port” is the 10BaseT interface. This port is designed to connect directly to a 10BaseT network. Figure 4, below, shows the Signal/Pin relationships on this interface.
4.0 OPERATION 3.3 CONNECTING POWER The Model 2111 is available with a Universal AC power supply that is operable in power environments from 100 to 253VAC. No configuration is necessary for the power supply (See Appendix B for domestic and international power plug options). 3.3.1 Connecting to an AC Power Power Source The Universal Interface AC Supply is equipped with a male IEC320 power connection. A domestic (US) power supply cord is supplied with the unit at no extra charge.
TM NS Glows red to indicate that the Model 2111 has been placed in Test Mode. The unit can be placed in test mode by the local or remote user. Glow red to indicate that the local Model 2111 has not yet connected with the remote. 4.3 ETHERNET LED STATUS MONITORS The Model 2111 features two LEDs that monitor general operating status and the 10Base-T twisted pair link integrity (located on the rear of the unit). Figure 5 (below) shows the LEDs located directly beneath the RJ-45 jack.
APPENDIX A 2. If the above test indicates no errors are present, move the V.52 toggle switch DOWN, activating the “511/E” test with errors present. If the test is working properly, the local modem's red “ER” LED will glow. A successful “511/E” test will confirm that the link is in place, and that the Model 2111’s built-in “511” generator and detector are working properly. 13 PATTON ELECTRONICS MODEL 2111 SPECIFICATIONS LAN Connection: RJ-45, 10Base-T, IEEE 802.
APPENDIX B PATTON ELECTRONICS MODEL 2111 FACTORY REPLACEMENT PARTS AND ACCESSORIES Description Patton Electronics Model # 0805US ...........................American Power Cord 0805EUR.........................European Power Cord CEE 7 0805UK ...........................United Kingdom Power Cord 0805AUS .........................Australia/New Zealand Power Cord 0805DEN.........................Denmark Power Cord 0805FR............................France/Belgium Power Cord 0805IN.............................
APPENDIX D MODEL 2111 INTERFACE PIN ASSIGNMENT (continued) Line Interface Pin Description (RJ-45 Female Connector) 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 (N/C) (N/C) (N/C) (Tip) (Ring) (N/C) (N/C) (N/C) Figure 3. Model 2111 twisted pair line interface. Dear Valued Customer, Thank you for purchasing Patton Electronics products! We do appreciate your business. I trust that you find this user manual helpful.
