USER MANUAL MODEL 1068 Variable Rate VLINK Modem Part# 07M1068-A Doc# 058111UA Revised 6/10/02 An ISO-9001Certified Company SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007
CONTENTS 1.0 1.1 1.2 1.3 1.4 1.5 Warranty Information ................................................................. Radio and TV Interference............................................................ CE Notice...................................................................................... FCC Part 68 (1068DV Only) ......................................................... Industry Canada Notice ................................................................ Service..............................
C.2 VDSL Interface ............................................................................ 23 RJ-45 .......................................................................................... 23 Terminal Block............................................................................ 23 C.3 POTS/ISDN Interface .................................................................. 23 RJ-45 ..........................................................................................
1.0 WARRANTY INFORMATION Patton Electronics warrants all Model 1068 components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of the shipment. This warranty is limited to defects in workmanship or materials, and does not cover customer damage, abuse or unauthorized modification. If this product fails or does not performs as warranted, your sole recourse shall be repair or replacement as described above.
1.3 FCC PART 68 (1068DV ONLY) The Model 1068D is not intended to be connected to the public telephone network. Caution The VLINK port is not intended to be connected to the public telephone network. The 1068DV contains a POTS/ISDN connection that can be connected to the public telephone network. Caution This equipment complies with Part 68 of the FCC Rules. Please note the following: 1. You are required to request service from the telephone company before you connect the Model 1068DV to a network.
3. If your Model 1068DV causes harm to the telephone network, the telephone company may temporarily discontinue your service. If possible, they will notify you in advance, but if advance notice is not practical, you will be notified as soon as possible and will be informed of your right to file a complaint with the FCC. 4. If you experience trouble with the Model 1068DV, please contact Patton Electronics Company for service or repairs. Repairs should be performed only by Patton Electronics Co. 5.
2.0 GENERAL INFORMATION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for one year for parts and labor. If any questions or problems arise during installation or use of this product, contact Patton Electronics Technical Support at +1 (301) 975-1007. 2.
passed transparently (unmodified) through the 1068s. The 1068s automatically add and delete MAC addresses, only passing packets across the VDSL link that are meant for the remote peered LAN. Figure 1. Typical application The 1068DV/CO and 1068DV/CP work together to create a transparent extension between two peered Ethernet LANs. POTS/ISDN calls can be made over a VDSL link without interfering with the data. Figure 1 shows a typical point-to-point application.
3.0 INSTALLATION Because the Model 1068 requires no configuration, it can be installed quickly. If you are installing a standalone unit, refer to section 3.1 “Standalone unit installation”. Otherwise, refer to section 3.2 “Rack card installation”. Note If asymmetric transmission or line rates other than 12.5 Mbps are required, refer to section 4.0, “Configuration” on page 15. 3.1 STANDALONE UNIT INSTALLATION Do the following: 1. Connect the line interface between the units (refer to section 3.
3.2 RACK CARD INSTALLATION The Model 1068 rack card version comprises a front card and a rear card.Do the following to install the cards into the rack chassis: 1. Slide the rear card into the back of the chassis along the metal rails. 2. Secure the rear card using the supplied metal screws. 3. Slide the front card into the chassis until you feel resistance as the front card engages the rear card.
6. Connect the Ethernet interface (refer to section 3.4, “Connecting the 10/100Base-T Ethernet Interface” on page 12). 3.3 CONNECTING THE TWISTED-PAIR LINE INTERFACE The Model 1068 supports communication between two peer Ethernet LAN sites over a distance of up to 6,652 ft (2.03 km) over 24 AWG (0.5 mm) twisted-pair wire. Note Actual distance and link performance may vary depending on the environment and type/gauge of wire used. Follow the steps below to connect the Model 1068 VDSL Interfaces.
The terminal block connector on the Model 1068's twisted pair interface is polarity insensitive and is wired for a two-wire interface. The signal/pin relationships is shown in Figure 5. A de in the US Ma r we Po K IN VL et rn he Et RING TIP Figure 5. Model 1068D (Terminal Block) twisted pair line interface. 3.4 CONNECTING THE 10/100BASE-T ETHERNET INTERFACE The shielded RJ-45 port labeled Ethernet is the 10/100Base-T interface.
Connecting the 10/100Base-T Ethernet Port to a Hub The Model 1068 10/100Base-T interface is configured as DTE (Data Terminal Equipment), just like a 10/100Base-T network interface card in a PC. Therefore, it “expects” to connect to a 10/100Base-T Hub using a straight-through RJ-45 cable. Figure 7 diagrams the cable wiring for connecting the Model 1068 to a 10/100Base-T hub. 1068 10/100Base-T Port RJ-45 Pin No. 10/100Base-T Hub RJ-45 Pin No.
work. The RJ-45 connector in the model 1068’s POTS/ISDN interface is wired as shown in Figure 9. 1 (no connection) 2 (no connection) 1 2 3 4 5 6 7 8 3 (no connection) 4 (2-wire RING) 5 (2-wire TIP) 6 (no connection) 7 (no connection) 8 (no connection) Figure 9. Model 1068DV (RJ-45) POTS/ISDN interface 3.6 CONNECTING POWER An external AC or DC power supply is available separately. This connection is made via the barrel jack on the rear panel of the Model 1068.
4.0 CONFIGURATION The Model 1068 has four DIP switches for configuring the unit for a wide variety of applications. This section describes switch locations and explains the different configurations. 4.1 CONFIGURING THE HARDWARE DIP SWITCHES Using a small flat-tip screwdriver, remove the protective cover located on the underside of the Model 1068 (see Figure 10). r we Po Lin k QO L VL IN K Lin k Act ivity Eth ern et VL INK Mo de m Figure 10.
S1 1 2 3 4 ON S1 1 2 3 4 O Switch toggle N S1 Push toggle down for OFF position S1 Push toggle up ON for ON position 1 2 3 4 Figure 11. DIP switch orientation S1 K Mo de m Po w VL er IN K S1 1 2 3 4 IN ON Lin k QO L et Switch toggle 4 k tiv 3 Lin 2 ity S1 Push toggle to left for ON position Push toggle to right for OFF position Figure 12.
4.2 CONFIGURING DIP SWITCH S1 DIP switch S1 is where you configure the VDSL line rate, symmetric or asymmetric, Ethernet full auto sense capability (100BaseT full or half duplex, 10BaseT full or half duplex) or limited auto sense (only 100BaseT half duplex, 10BaseT full or half duplex). Table 1 summarizes default positions of DIP switches S1-1 through S1-4. Detailed descriptions of each switch follow the table.
Table 3: Symmetric VDSL Line Rates Selection Chart S1-2 S1-3 S1-4 Symmetric Line Rate ON ON OFF OFF OFF ON 12.5 Mbps 16.67 Mbps Table 4: Asymmetric VDSL Line Rates Selection Chart S1-2 S1-3 S1-4 Asymmetric Line Rates DS/US OFF OFF OFF OFF ON ON ON ON OFF 4.17 Mbps/1.56 Mbps 9.38 Mbps/1.56 Mbps 16.67 Mbps/2.
5.0 OPERATION Once the Model 1068s are properly installed, they should operate transparently. No user settings required. This section describes reading the LED status monitors. 5.1 POWER UP Before applying power to the Model 1068, please review section 3.6, “Connecting Power” on page 14 to verify that the unit is connected to the appropriate power source. 5.2 FRONT PANEL LED STATUS MONITORS The Model 1068 features five front panel LEDs that monitor power, the Ethernet signals, and the VDSL connection.
V LIN K VL m de Mo r e w Po VLINK Link K IN Power VLINK QOL ink L OL Q E e th Ethernet Link et rn k n Li Ethernet Activity y vit ti Ac Figure 14. Model 1068 rack card front panel Table 5: Front panel LED description LED Power VLINK Link VLINK QOL Ethernet Link Ethernet Activity Description Solid GREEN to indicate the unit is powered on. (Active Green) Solid green (ON) to indicate that the end-to-end VDSL link between the Model 1068s is established.
APPENDIX A SPECIFICATIONS A.1 LAN CONNECTION • Shielded RJ-45, 10/100Base-T, IEEE 802.3 Ethernet • VDSL Connection: RJ-45 and Terminal Block A.2 TRANSMISSION LINE Two-wire unconditioned twisted pair. A.3 VDSL LINE RATE 16.67 Mbps, symmetric upstream/downstream. Additional symmetric and asymmetric rates are available via DIP switch settings. A.4 VDSL DISTANCE 6,000 ft (1.83 km) at 1.56 Mbps upstream/4.17 Mbps downstream Note Distances depend on selected line rate. A.
APPENDIX B MODEL 1068 SERIES FACTORY REPLACEMENT PARTS AND ACCESSORIES Patton Model # Description Base Models 1068DRC/CO 1068DRC/CP 1068DVRC/CO 1068DVRC/CP 1068D/CO 1068D/CP 1068D-2PK 1068DV/CO 1068DV/CP 1068DV-2PK 07M1068-A CO Variable Rate VDSL Rack Card; data only CP Variable Rate VDSL Rack Card; data only CO Variable Rate VDSL Rack Card; voice and data CP Variable Rate VDSL Rack Card; voice and data CO Variable Rate VDSL Modem, data only, no power supply CP Variable Rate VDSL Modem, data only, no p
APPENDIX C MODEL 1068 SERIES INTERFACE PIN ASSIGNMENT C.1 10/100BASE-T INTERFACE RJ-45 • Pin 1: TX+ • Pin 2: TX• Pin 3: RX+ • Pin 6: RX• Pins 4, 5, 7, 8: no connection C.2 VDSL INTERFACE RJ-45 • Pin 4: RING • Pin 5: TIP • Pins 1, 2, 3, 6, 7, 8: no connection Terminal Block See Figure 5 on page 12. C.
APPENDIX D DISTANCE CHART, BASED ON 24 AWG (0.5 MM) Symm Line Rate (DS/US) Distance in feet (km) 6.25 Mbps 9.38 Mbps 12.5 Mbps 16.67 Mbps 4,500 (1.37) 4,150 (1.26) 4,000 (1.22) 3,300 (1.00) Asymm Line Rate (DS/US) Distance in feet (km) 4.17 Mbps/1.56 Mbps (Mode 0) 9.38 Mbps/1.56 Mbps 16.67 Mbps/2.34 Mbps 6,000 (1.83) 5,500 (1.68) 5,000 (1.52) Copyright © 2001, 2002 Patton Electronics Company All Rights Reserved.
