Installation Instructions

ManualsBrandsPatriot Lighting ManualsIndoor LightingTrish Chrome Integrated LED Pendant

IMPORTANT SAFETY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS

PREPARATION

Please read and understand this entire manual before attempting to assemble,

operate or install the product.

Please save this instruction manual.

WARNING

• Turn off electricity at main fuse box (or circuit breaker box) before beginning

installation by removing fuse (or switching off circuit breaker).

• Be careful not to damage or cut the wire insulation (covering) during fixture

installation. Do not permit wires to contact any surface having a sharp edge.

To do so may damage or cut the wire insulation, which could cause serious

injury or death from electric shock.

• This product must be installed in accordance with the applicable installation

code by a person familiar with the construction and operation of the product and

the hazards involved.

• Connect the ground wires (bare copper or green) from your fixture to the ground

wire (bare copper or green) or ground screw in the electrical box.

CAUTION

• All electrical connections must be in agreement with local codes, ordinances or

the national electric code (NEC). Contact your municipal building department to

learn about your local codes, permits and/or inspections.

• Risk of fire – most dwellings built before 1985 have supply wire rated for 140°F/60ºC.

Consult a qualified electrician before installation.

• Do not connect this fixture to an electrical system that does not provide a means for

equipment grounding. Never use a fixture in a two-wire system that is not grounded.

If you are not sure your lighting system has a grounding means, do not attempt to

install this fixture. Contact a qualified, licensed electrician for information with regards

to proper grounding methods as required by the local electrical code in your area.

• If a dimmer control switch is used with this fixture, obtain professional advice to

determine the correct type and electrical rating required.

Before beginning assembly, installation or operation of product, make sure all parts

are present. Compare parts with package contents list and diagram on previous page.

If any part is missing or damaged, do not attempt to assemble, install or operate the

product. Contact customer service for replacement parts.

Tools Required for Assembly (not included): Slotted Screwdriver, Phillips Screwdriver,

Pliers, Electrical Tape, Wire Cutters, Safety Glasses, Ladder, Wire Stripper

Electrical

Box

Screw

1. Install the rods (EE) as shown.

Screw the bottom rod first. Install

swivel to the rod (EE), ensuring that

the sleeve is at the swivel.

2. Connect the ground wires from

your fixture to the ground wire or

ground screw in the electrical box.

Connect the black wire from the

fixture to the black wire in the

electrical box and connect the white

wire from the fixture to the white wire

in the electrical box. Use supplied

wire nuts (AA) for all wire connec-

tions.

3. IMPORTANT: Once connec-

tions of wires are completed,

carefully tuck wires and wire nuts

(AA) into the electrical box

making sure no bare wire is

visible at the wire nuts (AA).

4. Remove one screw to remove the

mounting bracket (BB) from the

fixture. Mount the mounting bracket

(BB) to electrical box using electrical

box screws (CC).

5. Position fixture over the mounting

bracket. Line up the screw in the

bracket to the"7"hole on the fixture.

Slide fixture to secure in place.

Insert remaining screw. Tighten both

screws to secure.

dimmable

This LED light is suitable to

be dimmed by

Leviton # 742-6672-HLW,

722-6674-PDW MAX 150 W,

Lutron # SCL-153PH-WH,

DVWCL-153PH-WH,

TGCL-153PH-WH MAX 150 W,

Eaton # SAL06-W-K

MAX 150 W.

The MAX rated wattage of

this model is 17 W

Black

House Supply

Ground Wire

Fixture

Ground wire

Red

White

(Neutral)

Black

(Hot)

Sleeve

Swivel