Installation Instructions

ManualsBrandsPatriot Lighting ManualsIndoor LightingArched Door 1848 Lumens 24 x 11 White LED Decorative Wrap Light

Fig. 12

Fig. 13

Connect the supply leads from the electrical

box to the fixture wire leads using the

pre-installed push-in connectors as per the

illustration (Fig. 12). Insert the black supply

lead into the open hole in the push-in

connector with the black fixture wires

already inserted into it (Fig. 13). Insert the

white supply lead into the open hole in the

push-in connector with the white fixture wires already inserted into it. All wire

connections should be made on the backside of the fixture. Carefully push the

excess wires back inside the electrical box.

Fig. 14

Fig. 15

Fig. 16

Position the fixture pan over the long machine

screws attached to the mounting bracket, insert

the screwheads into the keyhole slots by engaging

the straight keyhole slot over the first

screwhead. Use this as a pivot point and maneuver

the curved keyhole slot over the second

screwhead (Fig. 14). Maneuver the fixture until both

screwheads are engaged in the narrow channels

of both keyhole slots. Once the mounting screws

are engaged, maneuver the fixture until the desired

positioning of the fixture has been achieved

(Fig. 15). Fully tighten the mounting screws (Fig. 16).

NOTE: Fixture MUST be properly secured to the

electrical box first. The primary fixture support is

ALWAYS the electrical box.

*Actual fixture and hardware may differ from the illustrations.

Hardware Kit*

Fixture*

Fixture Installation

If extra support is needed use the included drywall

anchors. Position the fixture over the electrical box

and locate the circular openings near each end of

the fixture. Mark their position on the mounting

surface (Fig. 17).

Fig. 17

Diffuser

Fig. 19

Fixture pan

Locking tabs

Push-in

connectors

Drywall anchor

Support chain

Mounting bracket

Push-in

connectors

Fixture pan

Locking tabs

Support chain slot

Warnings and Cautions

WARNING

•

Shut off power at the circuit breaker or fuse panel before removing the old fixture

or installing the new one.

• LEDs can be damaged by electrostatic discharge (ESD) shock. Before

installation, discharge yourself by touching a grounded bare metal

surface to remove this hazard.

CAUTION

• This device complies with Part 15 of the FCC rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Disconnect power to the electrical box and remove the old fixture. If more than two

wire leads are present, keep track of which wires were connected together.

Using the support chain, connect one end to the back

of the fixture pan near the center in the specially

designed slots (Fig. 9) Hook the other end of the

support chain to the electrical box (Fig. 10). This

will allow for a hands free support for wiring.

Fig. 11

For safety and proper operation, the fixture must be

properly grounded. A green or bare copper ground

wire is preattached to the fixture pan. The fixture

ground wire must be spliced to the green or bare

copper ground wire in the electrical box using

one of the wire nuts (Fig. 11). If house wiring does

not include a ground wire, consult local electrical

code for approved grounding methods.

Fig. 9

Fig. 8

Prepare the mounting bracket by attaching both long

machine screws into two opposite round threaded

holes on the mounting bracket (Fig. 3). If the mounting

bracket has more than 2

threaded holes, measure the

distance between the keyhole

slots in the fixture pan (Fig. 4)

and match them up to the corresponding threaded

holes in the mounting bracket. Attach the screws to

the mounting bracket until they are against the mounting bracket.

If the keyhole slots are not punched through, remove

the appropriate knockouts from the back side of the

fixture pan that correspond to the positions of the

mounting screw heads on the mounting bracket (Fig. 8).

This can be done using a flathead screwdriver and

pliers.

Unscrew both long machine screws until the heads of

the screws extend about a 3/8 in. below the ceiling

surface (Fig. 7). NOTE: For proper installation, the

machine screws should be perpendicular to the floor.

Remove the existing screws from the electrical box. Pull

the supply wires from the electrical box through the

center hole of the mounting bracket. Attach the

mounting bracket to the electrical box, using the

electrical box screws removed earlier. Both long

machine screws installed in Step 1 should be installed

with both screwheads facing toward the floor (Fig. 5). If

the fixture needs to be parallel to a specific wall, align

the mounting bracket screwheads to run parallel

through the center run of the

fixture (Fig. 6).

Fig. 3

Fig. 7

Fig. 5

Fig. 6

Fig. 5

Fig. 4

Fig. 10

Insert the diffuser into the fixture pan (Fig. 21).

While holding on to the diffuser, rotate all

locking tabs counter-clockwise to lock

the diffuser in place (Fig. 22).

Fig. 21

Fig. 22

Rotate all locking tabs clockwise to unlock the

diffuser from the fixture pan (Fig. 1). Carefully

remove the diffuser (Fig. 2).

Fig. 18

Fig. 20

CEILING JOIST MOUNTING: While holding the

fixture in line with the pilot holes, screw the wood

screws into the wooden studs (Fig. 18). Tighten

until the fixture has been secured to the mounting

surface.

DRYWALL MOUNTING: Drill A 3/16-in. pilot hole into

the drywall (Fig. 19). Insert, and then screw the

drywall anchors all the way into the pilot holes. Tap

the drywall anchor head with a hammer, until it is

flush with the mounting surface. Hold the fixture in

line with the drywall anchors that were installed

and drive the wood screws into the drywall anchors

(Fig. 20). Tighten until the fixture has been secured

to the mounting surface.

IMPORTANT: This light fixture uses light emitting diodes (LEDs) to provide

light. LEDs do not have a filament to burn out like a traditional light bulb.

LEDs gradually emit less light over their lifetime, but will typically last 36,000

hours in a residential environment.

Periodically clean the fixture and diffuser using a mild, non-abrasive cleaner

and soft cloth. When cleaning the fixture, make sure the power is turned off.

Do not spray cleaner directly onto any part of the fixture or LEDs.

Care and Maintenance

Minor problems often can be fixed without the help of an electrician. Before doing any work

on the fixture, shut off power supply at the circuit breaker panel to avoid electrical shock.

Problem Cause Solution

Fixture doesn’t light. Power is off. Check if power supply is on.

Bad connection. Check cords and/or wiring.

Bad switch. Test or replace switch.

Fuse blows or circuit breaker Discontinue use. Call customer service.

trips when light is turned on.

Troubleshooting Guide

Important Safety Instructions

Fixture Callouts

WARNING: To reduce the risk of FIRE, ELECTRIC SHOCK, OR INJURY TO

PERSONS:

1. For INDOOR USE ONLY.

2. Do NOT touch LEDs.

3. Do NOT look directly at lighted LEDs for any length of time.

4. Do NOT touch, operate, or install fixture while in contact with water.

5. Not intended for illumination of aquariums.

6. For electrical requirements, see back of the fixture. Minimum 90° supply

conductors.

7. Do not leave bare wires exposed outside of the electrical box.

SAVE THESE INSTRUCTIONS IN A LOCATION CLOSE TO THE FIXTURE TO

REFER TO THEM AT A LATER TIME.

THIS FIXTURE IS DIMMABLE BY SPECIFIC FORWARD PHASE ELECTRONIC (TRAIC)

DIMMERS AND IS NOT COMPATIBLE WITH 0-10V DIMMING SYSTEMS. Dimmers

tested to be compatible with this fixture are the Lutron: Diva® C•L™: DVWCL-153PH,

Lumea® C•L™: LGCL-153PLH, and Toggler® C•L™: TGCL-153PH. (This list of dimmers

does not imply any guarantee or warranty of compatibility with a particular

application. Dimmers not listed do not imply non-compatibility.)

Dimmer Instructions

Center run of the fixture

Questions? Call our Customer Service Center 1-800-291-8838 or visit www.goodearthlighting.com/support.

To Begin

Arched Door Flush Mount Linear LED Ceiling Fixtures

ITEMS REQUIRED

Installation Time: 45 Minutes.

WARNING: Review important safety instructions before

installation. Check to make sure you have the following:

Flathead

Screwdriver

Phillips

Screwdriver

Pliers Wire Cutters

Electrical Tape Safety Glasses

Wire Strippers

Step Ladder

Item #: 348-3651

48” Linear Ceiling Fixture

Model #LF1057-WH1-48LF5-T

Item #: 348-3650

24” Linear Ceiling Fixture

Model #LF1057-WH1-24LF1-T

Item #: 348-3651

Item #: 348-3650

Need Help?

If you have questions regarding installation please call the

Customer Care Center 1-800-291-8838 or visit www.goodearthlighting.com/support.

Patriot Lighting

Warranty

1816INS1057-24-48

Printed in China

Distributed by:

Good Earth Lighting

1400 East Business Center Drive, Ste. 108

Mount Prospect, IL 60056

FIVE-YEAR LIMITED WARRANTY: If, during normal use, this

PATRIOT LIGHTING® light breaks or fails due to a defect in

material or workmanship within five (5) years from the date of

original purchase, simply bring this light with the original sales

receipt back to your nearest MENARDS® retail store. At its

discretion, PATRIOT LIGHTING® agrees to have the light or any

defective part(s) repaired or replaced with the same or similar

PATRIOT LIGHTING® product or part free of charge, within the

stated warranty period, when returned by the original purchaser

with the original sales receipt. This warranty; (1) excludes

expendable parts; (2) shall be void if this fixture is used for

commercial and/or retail purposes; and (3) does not cover any

losses, injuries to persons/property or costs. This warranty does

give you specific legal rights and you may have other rights,

which vary from state to state.

Parts List

Keep this guide handy for ordering replacement parts.

Hardware kit

ZH-LF1057F24-WH1

ZH-LF1057F48-WH1

Diffuser

ZD-LF1057L48-WHS

Diffuser

ZD-LF1057L24-WHS

Fig. 1

Fig. 2