Installation Instructions

Question/Comment/Missing Part?
Customer Service 1-800-205-6201
WARNI NG:
TO AVOID RISK OF ELECTRICAL SHOCK
TURN OFF OR DISCONNECT FROM POWER
WHILE INSTALLING OR SERVICING UNIT
Installation Instructions: 351-0018 (M-FP-7S-W) | 7.5" 1000 Lumen LED Square Flat Panel Light
TROUBLE SHOOTING
Problem Possible Cause Solution
The xture does not light The power is off Check that the power supply is ON.
There is a bad wire connection. Check the wiring
The switch is defective Test or replace the switch
Circuit breaker trips when power is
sent to the light.
Incorrect wire connections, or hot
wires are grounding out.
Ensure wires are connected
correctly.
INSTALLATION INSTRUCTIONS (For Junction Box)
1. If you want to install one of the provided trims;
place the trim over the front face of the LED light
and bend the clips around the back to latch it in
place.
2. Safety Concern! Always turn off the power at the
breaker when installing light xtures.
3. Disconnect the male E26 adapter (DD), Grounding
Wire and Screw (FF, II), and the Mounting Bracket
(BB).
4. Locate each wire: hot (black), Neutral (white)
and ground (green or bare copper) on the
connection wire (EE). Connect these wires to
their corresponding junction box wires using the
provided wire nuts (HH). Refer to Fig 1. Be sure
to attach the grounding wire (FF) to the mounting
plate (BB) with the grounding screw (II).
5. Before installing, use the Color Temperature
Guide Card select whichever color temperature
best ts your environment with the selector on
the back of the light.
6. Screw the mounting bracket (BB) into the junction
box with the provided screws (GG). Refer to Fig 2.
7. Press the LED light into the mounting bracket,
making sure that the clips engage and are secure.
Refer to Fig 3.
1. 2.
Insert the torsion springs into the fixture housing brackets .
When installing trim into a 5 in. recessed housing, the torsion
spring (FF) must be moved. Unscrew the torsion spring (FF) from
the 6 in. position and move it to the 5 in. position (See Fig. 4).
Gently push the fixture into the recessed housing (See Fig. 5).
Insert the torsion springs into the fixture housing brackets .
When installing trim into a 5 in. recessed housing, the torsion
spring (FF) must be moved. Unscrew the torsion spring (FF) from
the 6 in. position and move it to the 5 in. position (See Fig. 4).
Gently push the fixture into the recessed housing (See Fig. 5).
Question/Comment/Missing Part?
Customer Service 1-800-205-6201
WARNING:
TO AVOID RISK OF ELE CTRICAL SHOCK
TURN OFF OR DISCONNECT FROM POWER
WHILE INS TALLING OR SE RVICING UNIT
Installation Instructions: 351-0018 (M-FP-7S-W) | 7.5" 1000 Lumen LED Square Flat Panel Light
TROUBLE SHOOTING
Problem Possible Cause Solution
The power is off Check that the power supply is ON.
There is a bad wire connection. Check the wiring
The switch is defective Test or replace the switch
Circuit breaker trips when power is
sent to the light.
Incorrect wire connections, or hot
wires are grounding out.
Ensure wires are connected
correctly.
INSTALLATION INSTRUCTIONS (For Junction Box)
1. Safety Concern! Always turn off the power at
the breaker when installing light fixtures.
2. Disconnect the male E26 adapter (DD),
Torsion Brackets (CC), and the Mounting
Bracket (BB).
3. Locate each wire: hot (black), Neutral (white)
and ground (green or bare copper) on the
connection wire (EE). Connect these wires to
their corresponding junction box wires using
the provided wire nuts (II) and electrical tape.
Refer to Fig 1.
4.
Before installing, use the Color Temperature
Guide Card select whichever color
temperature best fist your environment with
the selector on the back of the light.
5. Screw the mounting bracket (BB) into the
junction box with the provided screws (HH).
Refer to Fig 2.
6. Now connect the quick connect ends of (EE)
and the LED light.
7. Press the LED light into the mounting bracket,
making sure that the clips engage and are
secure. Refer to Fig 3.
1. 2.
GG
3.
BB
AA
EE
BB
II
GG
Ground wire and screw
Remove
3.
Insert the torsion springs into the fixture housing brackets .
When installing trim into a 5 in. recessed housing, the torsion
spring (FF) must be moved. Unscrew the torsion spring (FF) from
the 6 in. position and move it to the 5 in. position (See Fig. 4).
Gently push the fixture into the recessed housing (See Fig. 5).
Insert the torsion springs into the fixture housing brackets .
When installing trim into a 5 in. recessed housing, the torsion
spring (FF) must be moved. Unscrew the torsion spring (FF) from
the 6 in. position and move it to the 5 in. position (See Fig. 4).
Gently push the fixture into the recessed housing (See Fig. 5).
Question/Comment/Missing Part?
Customer Service 1-800-205-6201
WARNING:
TO AVOID RISK OF ELE CTRICAL SHOCK
TURN OFF OR DISCONNECT FROM POWER
WHILE INS TALLING OR SE RVICING UNIT
Installation Instructions: 351-0018 (M-FP-7S-W) | 7.5" 1000 Lumen LED Square Flat Panel Light
TROUBLE SHOOTING
Problem Possible Cause Solution
The power is off Check that the power supply is ON.
There is a bad wire connection. Check the wiring
The switch is defective Test or replace the switch
Circuit breaker trips when power is
sent to the light.
Incorrect wire connections, or hot
wires are grounding out.
Ensure wires are connected
correctly.
INSTALLATION INSTRUCTIONS (For Junction Box)
1. Safety Concern! Always turn off the power at
the breaker when installing light fixtures.
2. Disconnect the male E26 adapter (DD),
Torsion Brackets (CC), and the Mounting
Bracket (BB).
3. Locate each wire: hot (black), Neutral (white)
and ground (green or bare copper) on the
connection wire (EE). Connect these wires to
their corresponding junction box wires using
the provided wire nuts (II) and electrical tape.
Refer to Fig 1.
4.
Before installing, use the Color Temperature
Guide Card select whichever color
temperature best fist your environment with
the selector on the back of the light.
5. Screw the mounting bracket (BB) into the
junction box with the provided screws (HH).
Refer to Fig 2.
6. Now connect the quick connect ends of (EE)
and the LED light.
7. Press the LED light into the mounting bracket,
making sure that the clips engage and are
secure. Refer to Fig 3.
1. 2.
GG
3.
BB
AA
EE
BB
II
GG
Ground wire and screw
Remove
FF
II
HH