Installation Instructions

32
Please read and understand this entire manual before attempting to assemble, operate or install the product.
WARNING: When using outdoor use portable lighting products, basic safety precautions
should always be followed to reduce the risk of re, electric shock, and personal injury
including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
a) Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuits or outlet to
be used for the outdoor use exible lighting product. Receptacles are available that have built-in
GFCI protection for this measure of safety.
b) Only use outdoor extension cords such as type SEW, SEOW, SEOOW, SOW, SOOW, STW,
STOW, STOOW, SJEW, SJEOW, SJEOOW, SJW, SJOW, SJOOW, SJTW, SJTOW, or SJTOOW.
This designation is marked on the wire of the extension cord.
• Read and follow all instructions that are on the product or provided with the product.
• This product operates at 120V, 60Hz 0.15A 16.2W per string
• This seasonal use product is not intended for permanent installation or use.
• Do not mount or place near gas or electric heaters, replaces, candles, or other similar
sources of heat.
• Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
• Do not let lamps rest on the supply cord or on any wire.
• Unplug the product when leaving the vicinity of the product or when left unattended.
• This is an electric product and is not a toy! To avoid risk of re, burns, personal injury, and electric
shock, it should not be played with or placed where small children can reach it.
• Do not use this product for other than its intended use.
• Do not hang ornaments or other objects from cord, wire, or light string.
• Do not close doors or windows on the product or extension cords as this may damage the wire
insulation.
• Do not cover the product with cloth, paper, or any material not part of the product when in use.
• This product is equipped with screw type lamps. Do not twist lamps.
• Do not operate this product with lamps missing from sockets. Missing lamps should be
replaced promptly.
• Risk of re: This product does not contain lamp shunts which allow the product to operate if one
lamp burns out. Replace lamps only with the spare lamps provided with this product.
• DO NOT EXCEED THE MAXIMUM EXTENSION LENGTH IN FEET PERMITTED BY THE
MARKING. The maximum extension length for this string light is 540 feet or 15 units. When adding
additional extension pieces, use only PATRIOT LIGHTING
®
346-1103 36FT LED Warm White String Light.
SAVE THESE INSTRUCTIONS
Before beginning assembly, installation, or operation of product, make sure all parts are present. Compare
parts with package and hardware contents lists on page 1. If any part is missing or damaged, do not attempt
to assemble, install or operate the product. Contact customer service for replacement parts.
Tools Required for Assembly (not included): Phillips Screwdriver, Safety Glasses, Ladder, Supporting hard-
ware (eyebolts or brackets)
Estimated assembly time: 20 minutes
WARNING
• Disconnect power at the source prior to beginning installation or servicing product.
• Be careful not to damage or cut the wire insulation (covering) during xture installation. Do not permit power
cord or wires to contact any surface having a sharp edge. To do so may damage or cut the wire insulation,
which could cause serious injury or death from electric shock.
• String light sockets must be suspended so that lamps are facing downwards. DO NOT mount the light string
with sockets facing upward. Lamps should hang freely with at least 3 inches of space from nearest object.
SAFETY INFORMATION
PREPARATION
INSTALLATION INSTRUCTIONS
1. Carefully remove all the parts
from the packaging, and gently lay
them out on a smooth workspace.
Remove the packing material and
uncoil the string light (A). Be careful
not to cut or nick the string nor
damage the pre-attached lamps.
1
AAA
2. Fill each of the string light’s (A)
sockets with a provided S14 lamp
(B) by inserting the lamp into the
socket gently turning clockwise until
fully seated. Do not over-turn.
3. Securely attach string light
(A) to a support structure
using the eyelet holes at the
top of each suspended socket
and appropriate supporting
hardware (eyebolts, brackets,
etc. not included). The maximum
unsupported distance is 20 feet.
Use an appropriately rated cable
support system for spans over
20 feet (not included).
2
2
3
AAA
AAA
AAAAAA
AAA
AAA
B
B
4
5. Plug the beginning of
the string light (A) into an
appropriate power outlet.
Check to ensure each lamp
(B) lights up.
1. Ensure that all string lights
(A) are unplugged before adding
additional string light (A) segments
to the series.
2. Remove the end cap from the
last string light (A) in the series by
unscrewing the plastic end cap.
1
3. Connect two string lights
together by pushing the male and
female end connections together,
then tightening the screw-on
connection cover. Ensure the last
string in the series has its end cap
attached.
3
EXTENDING THE SERIES
AAA
Rotate