Installation Instructions
32
Before beginning assembly, installation, or operation of product, make sure all parts are present. Compare
parts with package and hardware contents list on page 1. If any part is missing or damaged, do not attempt to
assemble, install or operate the product. Contact customer service for replacement parts: 1-844-255-9692
Monday – Friday 9:00 a.m. – 6:00 p.m. CST.
Tools Required for Assembly (not included): Suitable Fasteners (eye bolts & spring clips for use with included
v-hooks and chain, cable with spring clips, or 1/2”NPT with junction box), Screwdriver, Tape Measure, Pencil,
Safety Glasses, and Ladder
SAFETY INFORMATION
PREPARATION
WARNING
• This xture requires a 100-277V AC electrical input with direct wire installation for operation and has three
adjustable wattage consumption settings: 180W, 200W, or 220W. Test that power is shut o at the source
with an electrical voltage tester before beginning
• Ensure mounting surface is sturdy and capable of holding the weight of the xture safely.
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS (continued)
WARNING: These products may represent a possible shock or re hazard if improperly installed or attached
in any way. Products should be installed in accordance with these instructions, current electrical codes, and/or
the current National Electric Code (NEC).
WARNING: To reduce risk of re, electric shock, or injury to persons, be sure that power supply is turned o
at fuse box or circuit breaker before attempting installation or servicing of the xture. For safest operation, read
and become familiar with complete installation instructions prior to use. Pay close attention to this manual and
stay within its guidelines when using this product.
SAVE THESE INSTRUCTIONS
ADDITIONAL SAFETY MEASURES
1. To avoid electrical shock, do not turn on xture with missing or damaged lens.
2. There are no serviceable parts inside LED module or xture.
3. LEDs emit bright light. Avoid looking directly at the light source.
4. Suitable for damp locations and operation in temperatures not exceeding 122°F (50°C)
5. For use in 100-277V, AC application
6. All parts must be used as indicated in this manual. Do not substitute any parts, leave parts out, or use parts
that are worn out or broken. Failure to obey this instruction could invalidate the ETL certication.
7. Do not mount over a sink, tub or shower.
L N
GND
L N
GND
3.
Install the cable clamp
connector (C) by inserting
the threaded end into the
knockout hole. Then
threading the locknut onto
the cable clamp
connector (C) from the
inside of the xture (A) and tighten the locknut with
pliers. Insert the supply wires
through the cable clamp
connector (C) into the xture (A), then tighten the
screws on the cable clamp connector (C) to secure
the cable.
A
A
A
Chain
Spring
Clips
180W 200W 220W
V-
Hooks
1. To mount the xture via chain with v-hooks and spring clips
(included): Attach V-hooks to the mounting holes located at
either end of the xture. Hook the spring clips on to the center
of the v-hooks. Adjust the chain length to a suitable distance
and ensure the xture is level. Secure the chain to the ceiling
and the spring clips.
2. To correctly wire the xture: connect supply GROUND to
xture GROUND (green) lead, connect supply NEUTRAL
to xture NEUTRAL (white) lead, and connect supply
POWER to xture POWER (black) lead.
For 0-10V dimming: connect DIM+ to xture (purple) lead,
connect DIM- to xture (gray) lead
*Dimming range for this xture is 0-100%
Ensure all connections are secure and follow local
electrical codes.
3. To adjust the power/wattage level of the xture, utilize the
switch on the front of the xture. Slide the switch over for 3
separate wattage settings: 180W, 200W, or 220W. Light output
will change as the power is adjusted.
Fig. 1
Fig. 2
Fig. 3