Installation Instructions

2 3
Before beginning assembly, installation, or operation of product, make sure all parts are present. Compare
parts with package and hardware contents list on page 1. If any part is missing or damaged, do not attempt to
assemble, install or operate the product. Contact customer service for replacement parts.
Tools Required for Assembly (not included): Ladder, safety glasses
Estimated assembly time: 10 minutes per xture
SAFETY INFORMATION
PREPARATION
WARNING: These products may represent a possible shock or re hazard if improperly installed
or attached in any way. Products should be installed in accordance with these instructions, current
electrical codes, and/or the current National Electric Code (NEC). Disconnect power to the unit prior
to installation.
WARNING: To reduce risk of re, electric shock, or injury to persons:
• Read all installation instructions before beginning. If you have any doubts about how to install this lighting
xture, or if the xture fails to operate completely, consult a qualied electrician to ensure correct branch
circuit conductor.
• This xture is designed for use in a circuit protected by a fuse or circuit breaker.
• Always be sure that power supply is turned o󰀨 at fuse box or circuit breaker before installing, cleaning, or
servicing the xture.
• This product must be installed in accordance with the applicable installation code by a person familiar with
the construction and operation of the product and the hazards involved.
• Supply conductors (power wires) connecting the xture must be rated minimum 90°C. If uncertain, consult
an electrician.
• To reduce the risk of re, electric shock or injury to persons, do not make or alter any open holes in a wiring
enclosure nor in any electrical components during kit installation.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
• There are no serviceable parts inside the xture.
• Suitable for use in dry locations.
• The installer must determine that supply power is 120V AC 60Hz at the luminaire before installation.
• The National Electric Code (NEC) does not permit cords to be concealed where damage to the cord’s
insulation may go unnoticed. To prevent re damage, do not run cord behind walls, ceilings, so󰀩ts, or
cabinets where it may be inaccessible for examination. Cords should be visually examined periodically and
immediately replaced when any damage is noted.
• Do not cover the xture with any heat insulated materials.
SAVE THESE INSTRUCTIONS. For safest operation, read and become familiar with complete installation
instructions prior to use. Pay close attention to this manual and stay within its guidelines when using this
product.
CAUTION:
• All parts must be used as indicated in this manual. Do not substitute any parts, leave parts out, or use parts
that are worn out or broken. Failure to obey this instruction could invalidate the ETL certication.
• LEDs emit bright light. Avoid looking directly at the light source.
• Account for small parts and destroy packing material, as these may be hazardous to children.
INSTALLATION INSTRUCTIONS
WARNING
• Turn o󰀨 electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse (or
switching o󰀨 circuit breaker).
• Be careful not to damage or cut the wire insulation (covering) during xture installation. To do so may damage
or cut the wire insulation, which could cause serious injury or death from electric shock.
• This xture is rated for 120V AC operation and draws 18W per xture. The installer must determine whether
supply power is appropriate prior to installation.
B
B
A
A
A
A
C
1. Turn the di󰀨user shade (B) counterclockwise to remove it
from the xture plate (A).
2.Connect the hot and neutral (black and white) wires
from the xture plate (A) to the same color wires from
the electrical junction box. Connect the green wire
from the xture plate (A) to the grounding wire from the
electrical box. Cover the wire connections using the wire
connectors (C). Wrap the wire connections with electrical
tape for a more secure connection. Position the wires
back inside the electrical junction box.
3. Assemble washer (F) onto screw (D). Align the keyholes
in the xture plate (A) with the mounting screws (D). Use
mounting screws (D) to secure xture plate (A) to the
electrical box. When installing on drywall, use drywall
screws (E) to further secure the xture.
4. This LED light xture allows you to customize the color
temperature of the light using three settings: soft white
3000K, cool white 4000K, or daylight 5000K. Move
the toggle switch on the xture plate (A) to make your
selection before attaching the di󰀨user shade (B) to the
xture plate (A). The factory setting for the correlated
color temperature (CCT) is 3000K, which is the warmest
white light.
5. Position the di󰀨user shade (B) into the xture plate (A).
Turn the di󰀨user shade (B) clockwise to secure it to the
xture plate (A). Restore power at the electrical panel.
Turn on power to activate the xture.
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
A
A