USER GUIDE RF&KEYPAD INTEGRATED LOCKER LOCK (model :PT400TWR) Version 1.
Table of Contents 1. Understanding PT400TWR Locker Lock ................................... 3 1.1 What is PT400TWR Locker Locks? .................................................... 3 1.2 Operating cards .................................................................................. 3 2. Types of Lock Operating Scenario ......................................... 4 2.1 Free Selection (Shared Use)................................................................. 4 2.2 Assigned Mode (Permanent Use) .........
1. Understanding PT400TWR Locker Lock 1.1 What is PT400TWR Locker Locks? - PT400TWR locker locks are the locker lock operated by either13,56 MHz RF keys or Digital touch keypads. - PT400TWR can work as both offline (stand alone) or online mode. - To set PT400TWR as online system, additional peripherals such as Access point, Server and client software are necessary. Refer Esmart Ultra client user manual for online lock system setup. 1.
• Lock ID, Operation mode, Battery status, software version, time, auto opening and more to be collected. 2. Types of Lock Operating Scenario PT400TWR locker locks are designed to work for the various operation requirements by simple set up process. Following operation modes can be programmed before or after lock installation. 2.1 Free Selection (Shared Use) - User can select any empty locker. - LED lamp is blinked to represent locker is in use.
3. Lock Operation 3.1 Pin Code & RF tag uses ① PT400TWR can be set with three different credential acceptance modes. ② Pin Code & RF tag mode accepts both Pin Code and RF tag ③ RF tag only mode accepts only RF tag ( no Pin Code available ) ④ Pin Code only mode accepts only Pin Code and does not read any RF tag. ⑤ These modes can be set from Maintenance card ( or setup card ) [Pin Code & RF tag] [RF tag only] [Pin Code only] 3.2 Assigned Mode 3.2.
3.2.2 Open & Close by RF card key ① RF card key can be used together with Digital Pin Code anytime. Touch Screen + Put User Card on the Lock. ② When user uses the RF card key, default Pin Code 1234 will be erased from the lock. However, User Pin Code except default Pin Code is not deleted. ③ When user wants to set new Pin Code, the process is same as in “Change Pin Code” while lock is in unlock position. Default Pin Code 1234 cannot be used as User Pin Code. 3.2.
the “Registration” button for a new registration. To register via the Mobile App, follow the instructions that will appear on your mobile device screen. The instructions are like following: - Scan your user card on the lock. - To enter registration mode, scan you user card again (the registration mode’s on when the lock’s LED is blinking) - Touch the “Register” button below. Now, when registration is done, your mobile key is fully synchronised with the user card and ready to operate the lock.
unlimited number of mobile devices can be assigned to one locker by syncing up with a card, but one mobile device can have only one card assigned, whereas one phone can operate up to 5 locker locks at the same time if its RF c a r d h a v e 5 locks assigned. Version 1.
(5) Access Log To check the history of the mobile access key, visit the “Access Log” panel in the Menu window. 3.3 Free Selection Mode 3.3.1 Open & Close by Pin Code ① Close： Touch Screen + self-selected 4 digit code + ② Open： Touch Screen + User’s 4 digit code + Bolt stays open 3.3.2 Open & Close by RF card key ① Touch Screen + Put User card on the lock. After it is unlocked, any 4 digit password can be used to lock it. User Pin Code will be deleted each time lock is opened. 3.3.
① Download Passtech Mobile App from Google play store and install it into his smartphone ② After running the App, choose ‘Free mode’ on the setting tab. ③ Then, you can freely choose any available lock to operate. To access your mobile device, please set your lock for CSN Free mode and change the usage mode to Free mode from the Passtech APP from your mobile device. 3.4 Open in Emergency ① In case User forgets his(her) password or lost card, Operator can open the lock by Master Card I or Master code.
(1) When battery reaches to low voltage ; ① Beep sounds five times. ② Red LED lights ③ Low battery is recorded in the memory of the User Card (Operator can know the low battery of the lock when the card is read at operator’s Program). (2) Changing battery ① Open the battery case at main case. ② Replace with new batteries. ③ When you replace batteries, do not mix the brands of them and use only brand new batteries.
4. Card Operation 4.1 Owner Card The role of the Owner card is to delete the Master card registration. Therefore, Owner card will be used to delete current master card registration in the lock, and make the lock to be ready to register new Master Card. It is simple to delete the Master card registration and to register new master card in the lock : ① Put the Owner card to the lock until lock sounds beep (one time) and red lamp lights. ② Now, all Master card registration is deleted from the lock.
4.2.1 Functions of the Master Card I & II ① There are two types of Master cards. ◆ Master card I : Alarm Off, Locker open and User card deletion. Useful card at user card lost. After Master card I scanned on a lock, the lock is ready to accept new user card. ◆ Master Card II : Alarm Off and Locker open and close. Useful card for temporary lock open or close. Previous user card is still assigned to the lock. ② Maximum five Master cards can be registered in a lock. 4.2.
Then, old master card you lost will not be used. ☞ All existing Master cards needs to be registered again together with new Master card because all master card registrations were deleted if Owner card is used. 4.3 User Card 4.3.1 Free Selection (Shared Use) The initial status of the lock in Free Selection mode is open (Latch is inside). (1) Initial Use ① Select the empty locker. ② Put your belongings in the locker.
③ Lock will check the lock ID and key of the user card (or any form of user key). ④ Lock will emit Green LED and beep sound once it is right user card . ⑤ Bolt will be moved and locker will open. ⑥ User information will be erased from the lock so that new user can use the empty lock. ☞ In free selection mode, lock and card needs to read and write the each other’s information. So please do not sway the card until the latch is moved. 4.3.
lock will register this locker number. Old User key will not be accepted. (2) Assigned Mode ① Issue new User card (with assigned locker Number) for Assigned mode. ② Put Master Card to the lock to delete the old user card, and put the new User card to the lock. ③ Lock will accept the new user card only, and old user card registration will be deleted. ④ In case the lock is set for multiple users, lock revision should be updated when new user card is issued by LOS program.
① Put Lock info Card to the lock. ② Various lock information data will be downloaded from locks to the Card. One card can collect up to 120 locks. ③ Read the Card at LOS program, and all data will be saved to the PC. ④ Lock ID, operation mode, Battery status, time, auto opening setting status, RF channel and more will be indicated. For further information about all system cards and how to issue, refer to LMS / LOS or Esmart ultra client manual. 5.
ANNEX A Beep & LED Table Beep LED Description 1 x short beep 1 x Green(2sec) OK 2 x short beep 1 x Red(2sec) Operation Error 3 x short beep 1 x Red & Green in Time over turn(2sec) Do-Re-Mi Melody 1 x Red & Green in Successful Set up / mode turn(2sec) change / Time setting 5 x short beep 5 x Red & Green Low battery Do-Re-Mi Melody 2 x Red & Green Successful connection between front and back bodies.
the memory of the lock. No Beep Both Green and Red LED 1) blinks Owner Card is not registered. 2) In case of Shift or Weekday operation mode, Alarm for shift or Time due. No Beep Red on/off Owner card is registered, but Master card is not registered. No Beep Green on/off Owner & Master card are registered, but User card is not registered Assigned Mode. Version 1.
ANNEX B Trouble Shooting 1) Master card registration should be followed after deleting old Master card in the lock by Master card registration in the lock was failed. Owner card. 2) Put Master card on the lock before waiting time is out after Owner card. Cannot open the lock with Master Master card is not registered in the lock. card Please Register the Master card in the lock. 1. Check the Setting of User card by LOS.
Thank you for selecting PT400TWR RFID/Keypad locks. Should you have any questions, please contact your local distributor or our technical support. FCC Statement 15.19: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 5.
