Installation Guide
P.01 V01
TM
www.partsmasterpro.com
TM
Installation Instructions
58525
Complete ReNu tub/shower remodeling kit
H
C
H
C
1
2
3
4
5
6
7
9
10
8
11
12
13
14
15
16 17
18
19
20
21
22
23
24
25
26
01. Index button
02. Screw
03. Broach washer
04. Handle
05. Foam
06. Limit stop sleeve
07. Washer
08. Escutcheon screws
09. Escutcheon
10. Seal washer
11. 6" Shower arm
12. Washer
13. Shower head
14. Shower escutcheon
15. Diverter tub spout
16. Teflon tape
17. Gasket
18. Bushing adapter
19. Slip-Fit adapter
20. Hex key
21. Screw
22. Overflow plate
23. Base
24. Bushing adapter
25. Strainer
26. Gasket
01. Index button
02. Screw
03. Broach washer
04. Handle
05. Foam
06. Limit stop sleeve
07. Washer
08. Escutcheon screws
09. Escutcheon
10. Seal washer
11. 6" Shower arm
12. Washer
13. Shower head
14. Shower Escutcheon
15. Diverter tub spout
16. Teflon tape
17. Gasket
18. Bushing adapter
19. Slip-Fit adapter
20. Hex key
21. Screw
22. Overflow plate
23. Base
24. Bushing adapter
25. Strainer
26. Gasket
H
C
H
C
C
D
B
A
Bath tub
E
1
4
3
2
5
6
7
9
8
1. Use screws(3) from old plate to secure base(2) in place.
2. Tighten screw(5) on overflow plate(4).
3. Install the strainer as is into bath tub drain for 1-1/2" but remove busing
adapter(7) then install strainer(8) and gasket(9) into bath tub drain(6) for
1-1/4" thread.
A & B
Installation
B
P.02 V01
1. Attach seal washer(2) on the bottom of escutcheon(1). Remove round foam(4) and paper(5) then stick square foam(3) on the escutcheon(1).
2. Insert washer(6) onto the cartridge(7) and install limit stop sleeve(8) onto the cartridge(7).
3. Secure screws(9) to connect escutcheon with valve body.
4. Install handle(10) and broach washer(11) using screw(12), and then with cover index button(13).
C
1. Install shower head(1) and washer(2) onto the shower arm(3).
2. Insert shower arm(3) into shower escutcheon(4).
3. Turn clockwise, wrap 2 to 4 turns of Teflon tape(5) onto shower arm nipple(3).
4. Tighten shower arm(3) into water pipe nipple(6).
1
2
3
4
6
5
5
4
3
2
1
H
C
H
C
6
7
8
9
10
12
13
11
1. Attach seal washer(2) on the bottom of escutcheon(1). Remove round foam(4) and paper(5) then stick square foam(3) on the escutcheon(1).
2. Insert washer(6) onto the cartridge(7) and install limit stop sleeve(8) onto the cartridge(7).
3. Secure screws(9) to connect escutcheon with valve body.
4. Install handle(10) and broach washer(11) using screw(12), and then with cover index button(13).
4. Install handle(10) and broach washer(11) using screw(12), and then with cover index button(13).
E-1
1
4
5
2
3
9
7
8
1. Apply 1 to 2 turns of silicon oil(1) onto pipe(2) end.
2. Slip adapter(3) onto pipe(2) and lean against the finish wall.
3. Install set screw(4) by hex key(5).
4. Turn clockwise, wrap 2 to 4 turns of Teflon tape(6) onto adapter(3).
5. Insert gasket(7) into extension nipple(8).
6. Fasten tub spout(9) onto the copper pipe(2).dd
1/2" Copper pipe
1" Min / 2"Max
6
1. Apply 1 to 2 turns of silicon oil(1) onto pipe(2) end.
2. Slip adapter(3) onto pipe(2) and lean against the finish wall.
3. Install set screw(4) by hex key(5).
4. Turn clockwise, wrap 2 to 4 turns of Teflon tape(6) onto adapter(3).
5. Insert gasket(7) into extension nipple(8).
6. Fasten tub spout(9) onto the copper pipe(2).d
6. Fasten tub spout(9) onto the copper pipe(2).
6. Fasten tub spout(9) onto the copper pipe(2).d
E-2
4
2
1/2" Thread nipple
4"
1. Turn clockwise, wrap 2 to 4 turns of Teflon tape(1) onto nipple(2).
2. Remove extension nipple(3) from tub spout(4).
3. Fasten tub spout(4) onto the nipple(2).
1
3
E-3
1
3
6
4
5
1/2" Thread nipple
1" Min / 2"Max
1. Turn clockwise, wrap 2 to 4 turns of Teflon tape(1) onto nipple(2)
and adapter(3).
2. Tighten adapter(3) onto nipple(2).
3. Insert gasket(4) into extension nipple(5).
4. Fasten tub spout(6) onto the adapter(3).
2
E-4
1
5
3
4
3/4" Thread nipple
1" Min / 2"Max
1. Turn clockwise, wrap 2 to 4 turns of Teflon tape(1) onto nipple(2).
2. Insert gasket(3) into extension nipple(4).
3. Fasten tub spout(5) onto the nipple(2).
2