2 A 8 3 20 5 11 4 11 8 20 18 9 3 1 13 22 B2 McCulloch oil 50:1 40:1 2% 20 cm3 100 200 300 400 1 ltr 5 10 15 20 2,5% 25 cm3 100 125 250 500 1 ltr 4 5 10 20 E2 H H 19 23 2 Strokes Engine totally sintetyc oil or Partner oil E1 21 7 B1 D 16 15 17 2 10 14 L F 6 24 F I MAX 8T A I G B3 G A C B B4 B5 L D E B6 F1 F2 F3 A A B C B Electrolux Outdoor Products Via Como 72 23868 Valmadrera (Lecco) ITALIA Phone +39 0341 203111 - Fax +39 0341 581671 Our policy of con
G1 G2 L1 L2 L3 30cc A C L4 0,095" 2,4 mm L5 197" 5000 mm B 538249346 249155 H1 H2 M1 4T M3 9" 230 mm 226134B 249155 H3 H4 A H5 C A 4T STOP 10" 255 mm 226135B 249155 M2 M4 B 8T STOP 9" 230 mm 246711B 249155 I M5 8T 10" 255 mm 236713B 249155 N1 supreme_300L_300B_copertina.p65 2 N2 N1 21/01/2004, 16.
A.
CAUTION! Danger of serious leg injuries. Take scrupulous care to follow the instructions in the manual. Maximum shaft speed. CAUTION! The cutting parts and muffler may get very hot and cause burns. Wait a few minutes before touching them. Danger of kickback. The blade is capable of amputating arms and legs. Prior to use • Do not use this machine for any other purpose than that for which it was designed, using the proper cutting devices as indicated in the instructions. • B1.
• • • • • be projected dangerously at a distance. Contact between the blades and any extraneous objects could cause serious injury to the operator or other people or animals in the vicinity, and could also damage the machine. B3. Cut only the material recommended for each accessory and take care not to let the blades come into contact with rocks, metal parts, etc. Take special care when working on sloping terrain. B4. Keep any other persons or animals away from the work zone (minimum distance 15 meters).
legs. The force of the kickback can cause the operator to lose control of the machine. Kickback can also occur when cutting with any type of blade in the hazardous zone (see N1); we therefore recommend cutting using the remaining zone. CAUTION! Always use a sharp blade. A blade with worn teeth can create problems in cutting and cause the blade to kickback. CAUTION! Do not sharpen a damaged or worn blade. Replace it with a new one.
Safety pole guard CAUTION! Never use a brush cutter without its safety pole guard correctly in place. This device, fastened to the machine, ensures a minimum distance between the operator and the cutting device during use, and prevents the machine from striking and injuring the operator if the blade hits a hard surface (fig. A no. 21). Muffler • The muffler serves to reduce the noise level to a minimum and to route the exhaust fumes produced by the combustion engine away from the operator.
• Fill the tank in a well-ventilated place. • Place the machine on a solid flat surface so that it cannot tip over, with the cap on the tank facing upward. • Clean the area around the fuel cap before removing it, to prevent any impurities from contaminating the fuel. • Take the cap off the fuel container carefully. Unscrew the cap on the fuel tank and fill it with the necessary quality, using a funnel. • Take care not to spill any fuel. • After filling the tank, screw the cap on tightly.
CAUTION! WE RECOMMEND THE USE OF ORIGINAL ACCESSORIES AND REPLACEMENTS, WHICH CAN BE PURCHASED FROM AUTHORIZED DISTRIBUTORS. THE USE OF OTHER ACCESSORIES AND REPLACEMENTS INCREASES THE DANGER OF ACCIDENTS AND IN THIS CASE THE MANUFACTURER HAS NO LIABILITY FOR DAMAGES TO PERSONS AND/OR PROPERTY. Assembly of nylon string head and blade Apply the proper guard depending on whether you plan to use the grass blade or nylon string head (see chapter: “Application of protective devices on cutter”). • F1.
CAUTION! Grip the knob of the starter with one hand and hold the machine in a stable position with the other. (Take care not to wind the starter string around your hand) and pull slowly until you encounter some resistance, then pull the cord sharply and forcefully (to start the engine when cold or warm follow the procedures described). CAUTION! Do not pull the starter cord all the way and do not release it abruptly against the machine as this could damage it. Startup of cold engine • H1.
L4. Spark plug Periodically (at least every 50 hours) remove and clean the spark plug and set the space between the electrodes (0.5/0.6 mm). Replace it if excessively encrusted or, in any case, after 100 working hours. In case of excessive encrustation check the carburetor adjustment, the percentage of oil in the fuel mixture and make sure the oil is of excellent quality and suitable for two-stroke engines. L5.
CAUTION! Do not use worn or damaged cutting devices. CAUTION! Twigs or grass may jam between the safety guard and the blade or nylon string head. Never try to remove this material with the engine running and the blade rotating. Always stop the engine before performing any operations of cleaning, and wait for the cutting device to stop in order to prevent injury. CAUTION! Try to limit contact and impact of the cutting devices against the ground and other objects as much as possible.
Take care that the cup supporting the blade just grazes the ground. This will prevent the blade from touching the ground. N1. CAUTION! WE RECOMMEND THE USE OF ORIGINAL ACCESSORIES AND REPLACEMENTS; THESE CAN BE FOUND AT YOUR OFFICIAL DISTRIBUTOR'S. THE USE OF ACCESSORIES AND REPLACEMENTS THAT ARE NOT ORIGINAL INCREASES THE DANGER OF ACCIDENTS AND IN THIS CASE THE MANUFACTURER IS NOT LIABLE FOR ANY DAMAGES TO PERSONS OR PROPERTY. O.
Q. Declaration of conformity The undersigned, authorized by E.O.P., declares that the following products model: type BC020 starting from the serial numbers produced from 2003 on, manufactured by E.O.P., Valmadrera, Italy, comply with European Directive: 98/37/EEC (Machine Directive), 93/68/EEC (EEC Marking Directive) & 89/336/EEC (Electromagnetic Compatibility Directive), directive 2000/14/EEC (Enclosure V). Valmadrera, 15.12.03 Pino Todero (Technical Manager) Electrolux Outdoor Products Italy S.p.A.
