T330+ GB FR DE ES INSTRUCTION MANUAL IMPORTANT INFORMATION: Please read these instructions carefully and make sure you understand them before using this unit. Retain these instructions for future reference. MANUEL D’INSTRUCTIONS RENSEIGNEMENTS IMPORTANTS: Avant d’utiliser cet appareil, veuillez lire atentivement les instructions et assurez--vous de les avoir comprises. Conservez les instructions pour référence ultérieure.
IDENTIFICATION (WHAT IS WHAT?) 1 2 4 6 10 7 9 8 19 3 13 14 15 20 16 11 21 12 17 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Fuel tank Handlebar ON/OFF switch Shoulder strap clamp Shoulder strap Trimmer head Line limiter blade Shield Shaft Coupler Blade 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. Throttle trigger Throttle lock--out Starter handle Fuel cap Primer bulb Choke lever Muffler Wrench Hex wrench Instruction manual Transport guard 18 22 5 IDENTIFICATION OF SYMBOLS A. D. F. I. B. E. G.
A. B. C. D. E. F. G. H. I. J. K. WARNING! This brushcutter can be dangerous! Careless or improper use can cause serious or even fatal injury. Read and understand the instruction manual before using the brushcutter. Always use: Ear protection, eye protection, head protection, boots, and gloves. DANGER! Blade can thrust violently away from material it does not cut. Blade thrust can cause amputation of arms or legs. Keep people and animals 15 meters away.
WARNING: The blade continues to spin after the throttle is released or, engine is turned off. The coasting blade can throw objects or seriously cut if accidentally touched. Stop the blade by contacting the right hand side of the coasting blade with material already cut. Stop coasting blade by contact with cut material. OPERATOR SAFETY S Dress properly. Always wear safety glasses or similar eye protection when operating, or performing maintenance, on your unit (safety glasses are available).
TRANSPORTING AND STORAGE S Allow the engine to cool; secure unit before storing or transporting in vehicle. S Empty fuel tank before storing or transporting the unit. Use up fuel left in the carburetor by starting engine and letting it run until it stops. S Store unit and fuel in an area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. S Store unit so line limiter cannot accidentally cause injury. Unit can be hung by the shaft.
NOTE: A one-half twist is built in the shoul- Secondary Hole Locking/Release Button in Primary Hole For optional attachments, see the ASSEMBLY section of the applicable attachment instruction manual. ATTACHING THE HANDLEBAR DANGER: To avoid serious injury, the barrier portion of the handlebar must be installed as shown to provide a barrier between operator and the spinning blade. 1. Locate the decal on the handlebar. This decal includes an arrow.
3. Pivot shield until bolt passes through hole in bracket. 4. Reinstall nut and tighten securely with wrench (provided). NOTE: If your unit has a plastic cover over the threads on the threaded shaft, remove the covering to expose the threads. Before installing the trimmer head, make sure the dust cup and retaining washer are positioned on the gearbox as shown below.
NOTE: Remove the trimmer head and plastic shield before attaching the metal shield and installing the weed blade. To remove the trimmer head, align hole in the dust cup with the hole in the side of the gearbox by rotating the dust cup. Insert a small screwdriver into aligned holes. This will keep the shaft from turning while loosening the trimmer head. Remove the trimmer head by turning clockwise. Remove the screwdriver. To remove the plastic shield, loosen and remove nut.
OPERATION Throttle Lock--out WARNING: Be sure to read the fuel information in the safety rules before you begin. If you do not understand the safety rules, do not attempt to fuel your unit. Contact an authorized service dealer. Choke Lever FUELING ENGINE WARNING: Throttle Trigger Remove fuel cap slowly when refueling. This engine is certified to operate on unleaded petrol. Before operation, petrol must be mixed with a good quality 2-cycle aircooled engine oil.
than 6 pulls. NOTE: If engine still doesn’t start, it is probably flooded. Proceed to STARTING A FLOODED ENGINE. 9. Once the engine starts, allow it to run 10 seconds, then move the choke lever to OFF CHOKE by aligning lever with position shown on decal (see following illustration). Allow the unit to run for 30 more seconds at OFF CHOKE before releasing the throttle trigger.
OPERATING POSITION ALWAYS WEAR: Hearing Protection Eye Protection Heavy, Long Pants Boots Cut from your left to your right. When operating unit, clip shoulder strap onto clamp, stand as shown and check for the following: S Wear eye protection and heavy clothing. S Extend your left arm and hold handlebar grip with your left hand. S Hold throttle grip with your right hand with finger on throttle trigger. S Keep unit below waist level.
OPERATING INSTRUCTIONS FOR USE WITH WEED BLADE Trimming 3 inches (8 cm) above ground SCALPING -- The scalping technique removes unwanted vegetation down to the ground. Hold the bottom of the trimmer head about 3 in. (8 cm) above the ground and at an angle. Allow the tip of the line to strike the ground around trees, posts, monuments, etc. This technique increases line wear. Scalping S Blade Thrust is a reaction that only occurs when using a bladed unit.
S Do not raise the engine above your waist as the blade can come dangerously close to your body. S Do not swing unit with such force that you are in danger of losing your balance. Bring the engine to cutting speed before entering the material to be cut. If the blade does not turn when you squeeze the throttle trigger, make sure shaft is fully inserted into the engine. Always release the throttle trigger and allow engine to return to idle speed when not cutting.
S Never use for spreading chemicals, fertilizers, or other substances which may contain toxic materials. S To avoid spreading fire, do not use near leaf or brush fires, fireplaces, barbecue pits, ashtrays, etc. CULTIVATOR SAFETY WARNING: Rotating tines can cause serious injury. Keep away from rotating tines. Stop the engine and disconnect the spark plug before unclogging tines or making repairs. WARNING: Inspect the area before starting the unit.
WARNING: Keep the pruner away from power lines or electrical wires. S Only use for pruning limbs or branches up to 4 inches in diameter. S Do not operate the unit faster than the speed needed to prune. Do not run the unit at high speed when not pruning. S Always stop the unit when work is delayed or when walking from one cutting location to another. S If you strike or become entangled with a foreign object, stop the engine immediately and check for damage.
CLEAN AIR FILTER A dirty air filter decreases engine performance and increases fuel consumption and harmful emissions. Always clean after every 5 hours of operation. 1. Clean the cover and the area around it to keep dirt from falling into the carburetor chamber when the cover is removed. 2. Remove parts as illustrated. NOTE: Do not clean filter in gasoline or other flammable solvent to avoid creating a fire hazard or producing harmful evaporative emissions. 3. Wash the filter in soap and water. 4.
CARBURETOR ADJUSTMENT WARNING: Keep others away when making idle speed adjustments. The trimmer head will be spinning during most of this procedure. Wear your protective equipment and observe all safety precautions. After making adjustments, the trimmer head must not move/spin at idle speed. The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions: S Engine will not idle when the throttle is released.
TROUBLESHOOTING TABLE WARNING: Always stop unit and disconnect spark plug before performing all of the recommended remedies below except remedies that require operation of the unit. TROUBLE CAUSE REMEDY Engine will not start. 1. ON/OFF switch in OFF position. 2. Engine flooded. 1. Move ON/OFF switch to ON position. 3. Fuel tank empty. 4. Spark plug not firing. 5. Fuel not reaching carburetor. 6. Carburetor requires adjustment. Engine will not idle properly.
DECLARATION OF CONFORMITY relating to 98/37/EC EC Declaration of Conformity (Directive 98/37/EC, Annex II, A) (Only applies to Europe) We, Electrolux Home Products, Inc., Texarkana, TX, 75501, USA, Tél.
