OT-200 User Manual
Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of PARTNER Tech Corp. Disclaimer The information in this document is subject to change without notice.
Revision history Version 1.0, July 2010 About this manual This manual is intended for system administrators who are familiar with setting up a new system and installing programs. The manual consists of the following sections: Chapter 1 Getting Started: Chapter 2 Using The Device: Chapter 3 Using The Accessories: Appendix: This section covers unpacking and checking the package contents, identifying components, charging the battery, installing the MicroSD card, and powering on the device.
Use the product with approved equipment: Use your product only with the computers and accessories Adjust the volume: Turn down the volume before using headphones or other audio devices. When device will not be used for a long period of time, please remove the battery, and store both device and battery in a cool, dark, and dry place. For storage over a long period of time, please place product in a dry box.
immediately with fresh water. Consult a doctor immediately. 3 time, let it stop charging. There is a possibility that the battery might be defective, and continued charging $ # Do not insert battery into a microwave or high pressure container.
TABLE OF CONTENTS CHAPTER 1 GETTING STARTED ................................................ 1 Unpacking the OT-200 ..................................................................................1 Checking the package contents ....................................................................2 Identifying components .................................................................................4 Charging Cradle .........................................................................................
...............................38 ! "# $%&' ..............................38 #*+ "# ; < =&' .............................38 Install and remove programs........................................................................39 CHAPTER 3 USING THE ACCESSORIES ............................... 41 Attaching the stylus cord ......................................................................
CPU Samsung S3C6410 667 MHz processor Operating System Microsoft® Windows™ Mobile 6.5 Professional Display 4.3” TFT LCD with Touch Screen, widescreen 800*480 Memory 256MB Flash, 256MB SDRAM Communication WiFi 802.11 b/g Bluetooth 2.0 class 2 Telecom standards ! " EDGE >?@ ! " Atheros Extension slot K @% ! @%Q " Interface Mini-USB 2.0 Other >* ! * " X ! " Internal microphone Speaker Y 4 $ !Z [ " \
Checking the package contents After you unpack the device check that the following items are included.
CPU Samsung S3C6410 667 MHz processor Operating System Microsoft® Windows™ Mobile 6.5 Professional Display 4.3” TFT LCD with Touch Screen, widescreen 800*480 Memory 256MB Flash, 256MB SDRAM Communication WiFi 802.11 b/g Bluetooth 2.0 class 2 Telecom standards ! " EDGE >?@ ! " Atheros Extension slot K @% ! @%Q " Interface Mini-USB 2.0 Other >* ! * " X ! " Internal microphone Speaker Y 4 $ !Z [ " \
Identifying components This section describes the parts and connectors on the OT-200. Front panel components 1 2 3 4 5 Figure 1.2 Front view Component 4 Description 1 ? !> ~ 2 | 3 _ !> ~ _ " 4 4.
Top and bottom panel components 1 2 6 3 5 4 Figure 1.3 Top and bottom view Component Description 1 Top hand strap eyelet 2 2.5mm microphone jack 3 Mini-USB port 4 Cradle connector 5 DC power jack 6 3.
Left and right side components 3 1 2 4 Figure 1.
Back panel components 1 2 3 4 Figure 1.
Charging Cradle This section introduces the charging cradle for the OT-200. The charging cradle is used to charge the OT-200. A second slot is also available for charging a spare battery. Top and front view of the cradle 1 2 3 Figure 1.6 Top view of the cradle 4 Figure 1.
Setup the OT-200 Refer to the following to setup the OT-200. 1. Remove the battery cover. Slide the cover downwards to open. Lift up to remove the battery cover.
2. Install the battery. Align the battery connectors on the battery with the pins in the battery compartment and insert the battery. 3. Replace the battery cover. Slide the battery cover back until it locks. 4. Install the screw if required.
5. Insert the plastic hinge, or attach the hand strap. (Refer to Chapter 3 - Attaching the hand " 6. Charge the battery. Open the power jack cover. Plug the AC adaptor power cord into an electrical outlet, then connect the DC plug of the adaptor cable to the OT-200. It takes approximately 6 hours to fully charge the battery for the @ $ CAUTION To avoid damaging OT-200 or the AC adaptor, make sure all connectors are properly connected. 7.
Using the cradle The charging cradle allows a more convenient way to charge OT-200. You can charge a spare battery ! " Charge the device in cradle 1. Plug the AC adaptor power cord into an electrical outlet, then connect the DC plug of the adaptor cable to the power jack at the back of cradle. 2. Insert OT-200 into the cradle with front of device on same side as front of cradle. 3.
IMPORTANT Please make sure to perform 3 complete full charge and discharge cycles to get optimal battery capacity. Failure to comply will result in shorter battery lifespan. Changing the battery Refer to the following to change the battery. 1. Press the Standby button to turn off the OT-200. 2. Remove the plastic hinge or the bottom of the hand strap. Slide the plastic hinge or hand strap down and away from the battery cover. 3. Remove the screw if the battery cover is locked.
4. Remove the battery cover. Slide the cover down, then lift up to remove. 5. Remove the battery by pulling on the plastic # 6. Install the new battery. Align the battery connectors on the battery with the pins in the battery compartment and insert the battery.
7. Replace the battery cover. Slide the battery cover back until it locks. 8. Reinstall the screw. 9. Replace the plastic hinge or the bottom of the hand strap.
Using MicroSD cards Use MicroSD cards for: Expanding the memory of the OT-200 Adding functionality The OT-200 supports SDHC MicroSD cards. SD cards must be purchased separately and are not included with the OT-200. NOTE Installing a MicroSD card Refer to the following to install a MicroSD card. 1. Press the Standby button to turn off the OT-200. 2. Remove the plastic hinge or the bottom of the hand strap. Slide the plastic hinge or hand strap down and away from the battery cover. 3.
4. Remove the battery cover. Slide the cover down, then lift up to remove. 5. Remove the battery by pulling on the plastic # 6. Slide the MicroSD slot clip horizontally to the open position.
7. Flip the clip. 8. Insert the MicroSD card into the slot with the label facing out. 9. Flip the clip back down. 10. Slide the clip to lock it.
View the contents of a MicroSD card Refer to the following to view the contents of a SD card. 1. Tap !@ " 2. Tap File Explorer. 3. Tap Storage Card to see a list of If the OT-200 does not recognize your MicroSD card, make sure you \ @% card into the slot.
20 C H A P T E R 1 G E T T I N G S TA R T E D
CHAPTER 2 USING THE DEVICE This chapter describes how to use OT-200 features. The following topics are described. Entering text You can use the Input Panel to enter text. To use the Input Panel, tap the on the taskbar. Tap keys on the Input Panel to enter text. Shortcut menus A shortcut menu is displayed when you tap and hold an item.
Performing a reset A reset stops all running applications, but does not erase any programs, saved data, or registry information. Be sure to close all running applications before performing a reset. NOTE To perform a reset: 1. Locate the recessed Reset button on the device. 2. Use the stylus to lightly press the Reset button. Opening and closing programs You do not need to exit a program to open another or to conserve memory. The system manages memory automatically.
Adjusting the volume 1. Tap the status bar. 2. Tap the Speaker icon. 3. Move the system/ phone volume slider on the screen to the required volume level. Also you can switch to On/ Vibrate or Off. 4. Tap the OK button.
Changing the device name The device name is used to identify the OT-200 in the following situations: Connecting with a computer Connecting to a network Refer to the following to change the device name. 1. @ @ @ About. 2. Select the Device ID tab. 3. Enter a name. The device name must begin with a letter, consist of letters from A to Z and numbers from 0 to 9, and should not contain spaces. 4. Tap the OK button.
Entering owner information Enter your personal information, such as your name and address, so that the OT-200 can be returned to you if it is lost. Refer to the following to enter the information. 1. @ @ ? Owner Information. 2. 6 3 personal information.
Recalibrating the screen If your stylus seems to be out of sync with the screen, then recalibrate the screen using your stylus. 1. @ @ @ Screen. 2. On the General tab, tap the Align Screen button. 3. Follow the displayed instructions to recalibrate. Please use the stylus to calibrate the screen for better accuracy.
Setting the date and time Refer to the following to set date and time. 1. Tap the status bar. 2. Tap the Clock icon. 3. Change the date or time and select the correct time zone. 4. Tap the OK button.
Setting the screen orientation Refer to the following to set the screen orientation. 1. @ @ @ @ 2. On the General tab select Portrait or Landscape.
Connecting to a WiFi network With wireless access, you can connect the device to the Internet. The OT-200 can connect to an IEEE 802.11b/g device or connect directly to other WiFi-enabled devices. Automatically connect to a WiFi network When you turn on the WiFi radio, OT-200 automatically detects WiFi networks that are broadcasting their !@@3% $ " 3 _ $ @@3% it manually.
6. Set the properties. Normally, all settings will be detected automatically. If necessary, you can change settings as follow. To use data encryption, select an encryption method from the Encryption list. To use authentication, select the authentication method from the Authentication list. 7. Tap the OK button. Manually connect to a WiFi network A wireless network can be added manually by entering the settings information to add the network.
5. Set the properties. 6. Enter the SSID. To use data encryption, select an encryption method from the Encryption list. To use authentication, select the authentication method from the Authentication list. 7. Tap the OK button. Find your IP address 3? ~ 1. Double tap or on the taskbar. 2. The WiFi IP address is displayed at the IP Information tab.
2. Double tap the Network and Dial-up Connections icon. 3. Double tap the WiFi connection icon. 4. Tap Specify an IP address. 5. Enter IP address, Subnet Mask, Default Gateway. 6. Tap the Name Servers tab on top 7. Enter the DNS or WINS addresses. 8. Tap the OK button.
Lock OT-200 ^ $ 6 *]'' private. !?3" $ $ % && " & ' & & && # NOTE To create or change the password 1. @ @ ^ $ 2. Select the Prompt if phone unused for check box. 3. Tap the list next to the Prompt if phone unused for check box, and then tap the amount of time that you want. 4. Tap the Password type list box, and then tap the type of password you want.
Unlock OT-200 !?3" $ 6 *]'' To unlock your phone 1. Drag the lock slider to either edge of the screen. 2. If you use a password, enter the password, and then click the icon for where you want to go: To go to the Desktop screen, tap Unlock. To go to your contacts,tap Contacts. To go to your e-mail, tap E-mail.
Synchronization By synchronizing OT-200 with your computer, you have access to the same information—your Microsoft 6 6 $ * $ 6 *]'' or your computer. It’s a good idea to synchronize regularly. Before you begin, get the Mini-USB to USB cable, you’ll use it to download and install a program that syncs content between OT-200 and your computer.
Synchronize your data with ActiveSync and Windows Vista/ 7 1. Download and install WMDC on your computer. If your computer is running Windows Vista or 7, _ \ % !_\% " visit http://www.microsoft.com/windowsmobile to download WMDC. 2. Plug OT-200 into the computer by using a Mini-USB to USB cable. 3. @ * ! * " 4.
+ @ !" #$%& 1. Connect OT-200 to the computer using a Mini-USB to USB cable. 2. On the computer, select Start > Programs > ActiveSync. 3. In the ActiveSync window, select Explore. 4. Double-click My Windows Mobile-Based Device. 5. 6 _ Y) 6.
Install and remove programs To install programs on the OT-200: 1. Use a Mini-USB to USB cable to connect the OT-200 to the computer. 2. Follow the instructions in the Installation Wizard provided with the program you want to install. 3. Check the screen on the OT-200 to see if any further steps are necessary to complete the program installation. To remove programs from the OT-200: 1. @ @ @ Remove Program. 2.
40 CHAPTER 2 LEARNING THE BASICS
CHAPTER 3 USING THE ACCESSORIES This chapter describes how to use the device accessories. Attaching the stylus cord Refer to the following to attach the stylus cord. 1. Thread the small loop of the stylus cord through the strap eyelet on the stylus and pull the other end of the cord through the small loop until the cord is 2.
Attaching the hand strap Refer to the following to attach the hand strap. 1. Insert the bottom of the hand strap into the slot at the bottom of the battery cover, until it clicks into place. 2. Thread the end of the hand strap through the top hand strap eyelet on the device then fold and stick together. The hand strap length can be adjusted by sticking the Velcro to a higher or lower position on the strap.
Using the leather pouch Using the leather pouch to carry the OT-200 is a good way to keep it protected. Simply insert the device into the leather pouch as shown below. A belt clip located on the back of the leather pouch allows you to wear the OT-200 on your side. In addition, a shoulder strap can be attached to the two integrated rings on the back side.
Attaching the leather pouch cord A leather pouch cord is provided to attach device to the leather pouch. 1. Open the battery cover. 2. Thread the small loop of the cord through the bottom corner strap eyelet on the device. Pull the other end of the cord through the small loop until the 3. Replace the battery cover. 4. Lock the other end of the cord to one of the rings on the back of the leather pouch. 5. To insert device into cradle for charging, simply detach as shown.
Using the high quality stylus A high quality stylus is included for your convenience.
46 CHAPTER 3 USING THE ACCESSORIES
APPENDIX This appendix describes locating and solving problems that you may encounter while using the OT-200. Troubleshooting Often after time spent troubleshooting, the problem is traced to something as simple as a loose connection. $ * Tips for Troubleshooting 3 * more quickly.
Why does the device operate slowly at times? Reset device. Does problem remain? If this solves problem, check if user installed applications are causing system to slow down. Check that enough free storage memory remains on device, If device shows low storage memory, delete unnecessary \ @% Having the OT-200 Serviced If you are unable to solve the problem, you should have the device serviced.
CPU Samsung S3C6410 667 MHz processor Operating System Microsoft® Windows™ Mobile 6.5 Professional Display 4.3” TFT LCD with Touch Screen, widescreen 800*480 Memory 256MB Flash, 256MB SDRAM Communication WiFi 802.11 b/g Bluetooth 2.0 class 2 Telecom standards ! " EDGE >?@ ! " Atheros Extension slot K @% ! @%Q " Interface Mini-USB 2.0 Other >* ! * " X ! " Internal microphone Speaker Y 4 $ !Z [ " \
50 APPENDIX
