Installation Manual
Table Of Contents
- A. Safety Information 3
- B. Other Conventions 5
- A. Overview of Installation 7
- B. Required Materials (Not Supplied) 7
- C. Design the Installation 7
- D. Install the Battery Charger 9
- E. Install the Order Point Speaker and Microphone Assemblies 12
- F. Install the Vehicle Detector(s) 13
- G. Assemble the PAR Drive Thru Headset G5. 13
- H. Install the Basestation 15
- I. Connect the Components 17
- J. Basestation to Component Wiring 20
- K. Auxiliary Detector Relays 21
- L. Installing Accessory Boards in the Basestation 23
- M. Power Up 26
- A. Enter Configuration Mode 28
- B. Navigating the Basestation Display 28
- C. Finding the MAC Address of the G5 Basestation 30
- D. Configuring with a Computer 30
- E. Logging into the Base Station with a PC 31
- F. Switching Between Lane1 and Lane2 31
- G. Menu Options for Lane1 and Lane2 32
- H. Change Basic Volume Settings 33
- I. Change Noise Reduction Level 39
- J. Set System Date and Time 39
- K. Change Global Settings 39
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets 42
- M. Order Taking Modes Setup 43
- N. Change Site Scheduling 43
- O. Change Site Information 44
- P. Digital IO Setup 45
- Q. Change Passcodes 45
- R. Split and Cross Lane Mode 46
- S. Installer Setup 46
- T. Factory Setup (Restore Factory Defaults) 47
- U. Create and Load Templates 47
- V. Reboot System 47
- W. Check the Revision Levels 48
- 1. Overview
- 2. Installation
- A. Overview of Installation
- B. Required Materials (Not Supplied)
- C. Design the Installation
- D. Install the Battery Charger
- E. Install the Order Point Speaker and Microphone Assemblies
- F. Install the Vehicle Detector(s)
- G. Assemble the PAR Drive Thru Headset G5H1
- H. Install the Basestation
- I. Connect the Components
- J. Basestation to Component Wiring
- K. Auxiliary Detector Relays
- L. Installing Accessory Boards in the Basestation
- M. Power Up
- 3. Configuration
- A. Enter Configuration Mode
- B. Navigating the Basestation Display
- C. Finding the MAC Address of the G5 Basestation
- D. Configuring with a Computer
- E. Logging into the Basestation with a PC
- F. Switching Between Lane1 and Lane2
- G. Menu Options for Lane1 and Lane2
- H. Change Basic Volume Settings
- Inbound Microphone Volume
- Outbound Talk Volume
- Vehicle Alert Volume
- Outbound Greeter Message Volume
- Change the Monitor Volume
- Inbound Listen
- Outbound Talk
- Vehicle Present
- Vehicle Approach
- Page Messages
- Greeter Messages
- Monitoring Audio Separately for the Two Lanes
- Change the Night Volume
- Registering Headsets
- Add Headsets
- Remove Headsets
- List All Headsets
- Resetting Inactive Days
- Checking Headset Software Revision
- Identifying Headset Serial Number
- I. Change Noise Reduction Level
- J. Set System Date and Time
- K. Change Global Settings
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets
- M. Order Taking Modes Setup
- O. Change Site Information
- P. Digital IO Setup
- Q. Change Passcodes
- R. Split and Cross Lane Mode
- S. Installer Setup
- T. Factory Setup (Restore Factory Defaults)
- U. Create and Load Templates
- V. Reboot System
- W. Check the Revision Levels
- X. Change the Microphone Preamp Gain
- Y. Installer Access
- 4. Troubleshooting
- 6. Appendix: Basestation Specifications
- 7. Appendix: Induction Loop and Vehicle Detector Board Specifications
- 8. Appendix: G5 Charger Specifications
- 9. Appendix: Best Practices
- 10. Appendix: PAR Acoustic Kit Installation Guide
- 11. Appendix: Loop and Cable Condition Test
- 12. Appendix: Upgrading a Single Lane Basestation to a Dual Lane
- 13. Index
4
Installation Instructions G5 Release A
WARNING
To reduce the risks associated with fire, explosion & property damage:
•
Immediately discontinue use of the battery if, at any time, the battery feels hot, changes color or shape, emits
an unusual smell, or appears abnormal or damaged in any other way.
•
Do not open, disassemble, pierce, crack, crush, incinerate, or expose to heat above 55 °C/130 °F. Keep bat-
teries away from children.
•
Do not store or carry batteries with metal objects. Store batteries in cool, dry, clean places.
•
Always replace batteries, battery chargers and power supplies, and all other system components with only
PAR approved units acceptable for use in this system to avoid system malfunction and safety concerns.
Replace model XT-1 battery with Model C1060/XT-1 only. Replace model G5 battery with Model G5L1 PAR
only. Use of another battery may present a risk of fire or explosion.
•
Do not immerse batteries in water or other liquids.
•
Do not use batteries that feel hot or that have changed in color or shape, emit an unusual smell, or appear
damaged or abnormal in any other way.
•
Discontinue use if damage or abnormalities are observed. Conduct regular visual inspections of batteries to
look for damage or abnormalities, such as changes in shape or color.
•
Use only PAR-approved batteries.
•
The
PAR
Drive-Thru Headset Battery Charger, G5 12-slot and the
PAR
Drive-Thru Headset Charging Sta-
tion, G5 are supplied with two power connections to allow for connecting an additional charger and/or
basestation. During installation, do not connect more than one power supply to one charger, or to the
interconnected string of chargers.
•
Do not modify this
PAR
Wireless Communication System Model XT-1, or
PAR
Wireless Communication
System Model G5.
•
For additional charging and use instructions, review the Installation Manual and the Operating Instructions.
AVERTISSEMENT
•
POUR ÉVITER TOUT RISQUE DE BLESSURE, D’ICENDIE OU D’EXPLOSION, NE PAS OUVRIS, ÉCRASER NI EXPOSERA À
DES TEMPÉRATURES SUPÉRIEURES À 55 C/ 130 F, CESSER L’UTILISATION SI LA PILE CHANGE DE FORME, ÉMET UNE
ODEUR INHABITUELLE OU SI ELLE EST CHAUDE L’UTILISATION D’UNE PILE AUTRE QUE PRÉSENTE UN RISQUE
D’INCENDIE OU D’EXPLOSIOON. CONSULTER LE MODE D’EMPLOI.
CAUTION
To reduce the risks associated with environmental contamination due to battery pack:
•
Dispose of batteries, power supplies, battery charger and basestation in accordance with federal, state & local
requirements. If preferred, return these components to PAR Service Center for recycle.
•
Many rechargeable batteries are required to be recycled by local, state/province, and national laws. To
properly recycle/dispose of the battery or battery pack, always follow local solid waste disposal regulations.
Additionally, in the United States and Canada, PAR is partnering with Call2Recycle (RBRC) to provide recycling
service to you to help ensure that the rechargeable batteries within our products are recycled properly. To
assist you in using this service call the Call2Recycle battery recycling information help line at
1-
800-8-BATTERY (1-800-822-8837) or consult Call2Recycle’s battery recycling guidance online at
www.call2recycle.org.