2-GEAR HAMMER DRILL PSBM 850 2-GEAR HAMMER DRILL Operation and Safety Notes E3334_PSBM 850_Cover_LB6.indd 2 11.04.
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device. GB / IE / CY Operation and Safety Notes E3334_PSBM 850_Cover_LB6.indd 3 Page 5 11.04.
9 1 2 3 8 7 6 5 4 A B C D E F E3334_PSBM 850_Cover_LB6.indd 4 11.04.
Kompernaß GmbH Burgstraße 21 44867 Bochum (Germany) Last Information Update: 04 / 2008 · Ident.-No.: PSBM850042008-6 E3334_PSBM 850_Cover_LB6.indd 1 11.04.
Table of content Introduction Proper use......................................................................................................................Page Features and equipment................................................................................................Page Included items................................................................................................................Page Technical data...............................................................................
Introduction The following pictograms are used in these operating instructions / on the device: Read instruction manual! Drilling Observe caution and safety notes! Impact drilling Caution – electric shock! Danger to life! Wear hearing protection, dust protection mask, protective gloves and protective glasses.
Introduction 5 6 7 8 9 Q Rotation direction switch Gear selector switch Auxiliary handle Quick-release chuck Depth stop Included items 1 Hammer-action drill PSBM 850 1 Auxiliary handle 1 Depth stop 1 Carry case 1 Operating instructions 1 „Warranty and service“ booklet Q Technical data Nom. voltage: 230 V ~ 50 Hz Rated power: 850 W No-load rotational speed: 1st gear max. 1450 min–1 2nd gear max. 3400 min–1 Impact cycles: 16 times rotation speed Chuck: Chuck capacity: 1.
General safety advice for electrical power tools eneral safety advice for G electrical power tools Warning! Read all the safety advice and instructions! Failure to observe the safety advice and instructions may result in electric shock, fire and / or serious injury. KEEP ALL THE SAFETY ADVICE AND INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE! 1. Workplace safety a) Keep your working area clean and well lit. Untidy or poorly lit working areas can lead to accidents.
General safety advice for electrical power tools carry it. Accidents can happen if you carry the device with your finger on the ON / OFF switch or with the device switched on. d) Remove any setting tools or spanners before you switch the device on. A tool or spanner left attached to a rotating part of a device can lead to injury. e) Avoid placing your body in an unnatural position. Keep proper footing and balance at all times.
General safety advice for electrical power tools / Before first use Always make sure that nobody is placed in any danger and that there are no inflammable materials near the working area. Warning! HAZARDOUS DUSTS! Working with harmful / poisonous dusts presents a danger to health for the tool operator and any persons in the vicinity. Wear safety glasses and a dust protection mask! J Avoid drilling paints containing lead or other substances hazardous to health.
Before first use / First use drill chuck 8 you can use the tool. The spindle lock releases automatically when the motor starts. Q First use The mains voltage at the mains socket must match that shown on the rating plate on the device. Devices marked with 230 V can also be operated at 220 V. Q Switching on and off When operating the hammer-action drill you can select between intermittent or continuous operation mode.
First use / Servicing and cleaning / Disposal / Information Drilling: j Set the drill / hammer-action switch 1 to the right into the position. Contact your local refuse disposal authority for more details of how to dispose of your worn-out devices. Impact drilling: j Set the drill / hammer-action switch 1 to the left into the position. Q Information Q Service centre Note: The hammer-action drilling mode is intended for drilling into brick, concrete and stone only.
Information Q Declaration Producer of conformity / We, Kompernaß GmbH, Burgstr. 21, 44867 Bochum, Germany, hereby declare that this product complies with the following EU directives: Machinery Directive (98 / 37 / EC) EU Low Voltage Directive (2006 / 95 / EC) Electromagnetic Compatibility (2004 / 108 / EC) Type / Description of product: 2-speed hammer-action drill PSBM 850 Bochum, 30.04.
