. Fit P1 into the slots in FW. Slide P2 into P1 and FW. Glue P1, P2 and FW together. FW 3. Fit and glue P3 to the motor mount assembly. Ensure that the notched tab in FW is fit into the slot in P3. P3 notched tab on FW 5. Drill a small hole(s) in the pod sides to allow access to the motor set screw in the motor mount. Fit and glue P5 in place. 7. Fit and glue MP2 into MP1. Sand the leading and trailing edges as desired. MP2 MP1 2. Secure the motor mount to the firewall FW.
9. Fit and glue the wing panels W1 and wa W2 together. 10. Fit and glue ribs R2-R5 to the wing panels. It is recommended to start by gluing the ribs to the trailing edge first, then the center and finally the leading edge. Make sure the ribs are fully seated into the notches in the trailing edge before gluing in place. Be sure to build a right and left wing panel. 11. Fit WS1 and WS2 into the slots Fit and glue the wing spar assembly into the slots in R2, R3 and the wing panel.
13. Fit and glue the second wing panel and wing spar assembly together. Make sure the leading and trailing edges of both wing panels are aligned and glue R1 to both wing panels. 14. Fit and glue the leading edge strips LE to the leading edge of the wing panels. 15. Sand the wing, rounding over the leading edge. Cover the wing, bottom first and then the top. 16. Cut a hole in the bottom of the pod large enough to pass the motor wires through. 17.
18. Fit and glue V10 into V9 as shown. CITY = v10 va 19. Cover and assemble the horizontal stabilizer assembly. Join the elevator halves with a 2" piece of the included CF rod. NO 20. Glue {" magnet into BH4. 21. Align the back edge of BH1 and BH2 and glue together. Glue BH3 to , BH2. Glue ยง" magnet into BH2. 3 Magnet BH4 BH2 BH3 + Magnet BH1 "Align back edge of BH1 and BH2 22. Glue ply rubber band hook to F3. 23. Install servos into servo tray. Rubber band hook : ST (servo tray) 25.
26. Fit dormers F1-F6, Battery Tray (BT) and servo tray (ST) into fuselage side FR. Be sure to orient the servo tray so that it tapers towards the rear. Do not glue anything in place yet. 27. Fit fuselage side FL to dormers F1-F8, Battery Tray (BT) and servo tray (ST).
29. Fit and glue the 5" balsa sheeting together. 30. Use a sanding bar to sand the bottom of the fuselage sides and dormers. Glue sheeting S3 to the fuselage bottom first, allow sheeting to overlap all edges. Sand S3 flush with the bottom of the fuselage at former F6. Glue sheeting S2 to the bottom of the fuselage. 31. Glue F4A to the fuselage sides and the sheeting S2.
32. Sand F4A flush with the bottom of the fuselage. Glue sheeting S1 to the bottom of the fuselage. 33. Sand the top of the fuselage. Glue sheeting S4 to the fuselage. 34. Sand the fuselage sides flush with the face of former F1. Stack and glue the I" balsa nose blocks to F1. Glue S5 in place. {baas nose blocks 35. Sand the fuselage sides. Check the fit of the battery hatch, sand as necessary for a good fit.
37. Make two (2) sponsors by gluing the sponsor sheeting S1A and S1B together. Fit and glue S2 and sponsor sides in place as shown in Fig.1. Bend and glue the sheeting around the sponsor sides as shown in Fig.2. Lightly wet the outside of the sheeting if necessary to help bend . 38. Cut two (2) pieces of CF rod (24.1cm) long and slide through holes in the fuselage. Fit sponsors onto the CF rods and glue in place. Equally space sponsors from fuselage and glue CF rods the the fuselage. Cut a (6.
41. Glue the vertical stabilizer sub fin to the bottom of the fuselage. Final Assembly and Flying 1. Attach control surfaces (elevator, rudder) to flying surfaces with clear packing tape, covering material or similar. Install pin style controls horns in the precept holes in the elevator and rudder. 2. Install motor, route wires through the pod and wing and connect motor leads to the ESC (Electronic Speed Control). Connect servos and ESC to the receiver and place the receiver right behind former F3.
