Round Flame Tower Heater OH-M744S-Stainless Steel OH-M744B-Heritage Bronze OH-M744BL-Hammered Blacak 5016039 ANSI 83.26-2014 CSA 2.
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. This manual contains important information about the assembly, operation and maintenance of this patio heater. General safety information is presented in these first few pages and is also located throughout the manual. Keep this manual for future reference and to educate new users of this product. This manual should be read in conjunction with the labeling on the product.
DANGER DANGER • EXPLOSION - FIRE HAZARD • CARBON MONOXIDE HAZARD • Never store propane near high heat, open flames, direct sunlight, other ignition sources or where temperatures exceed 120 degrees F (49°C). • This heater is a combustion appliance. All combustion appliances produce carbon monoxide (CO) during the combustion process. This product is designed to produce extremely minute, non-hazardous amounts of CO if used and maintained in accordance with all warnings and instructions.
Assembly Instruction WARNING & User's Manual WARNING ITEM NO. 13684811 • This product is fueled by propane gas. • Alert children and adults to the hazards of high surface temperatures. Stay away from these surfaces to avoid burning skin or igniting clothing. Propane gas is invisible, odorless and flammable. An odorant is normally added to help detect leaks and can be described as a “rotten egg” smell. The odorant can fade over time so leaking gas is not always detectable by smell alone.
Parts List PACKAGE CONTENTS AA A B PART DESCRIPTION QUANTITY Reflector Cover 1 A Reflector 1 B Emitter 1 C Support 3 D Protective Guard 3 E Ruby Quartz Glass Tube 1 F Burner Ignition Plate 1 G Control Box Casing 1 H Gas Hose & Regulator 1 I Back Panel 1 J Front Door Panel 1 K Wheel Kit 1 L Base Plate 1 C D E F G H I Pilot AA Hi Igniter Lo J K L INCLUDED HARDWARE OO EE Wrench Qty. 1 Bolt M8 x 15mm Qty. 2 HH DD Nut M8 Qty. 11 MM Screw M8 x 10 mm Qty.
Assembly Instructions PREPARATION Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents above. If any part is missing or damaged, do not attempt to assemble the product. Contact customer service for replacement parts. Estimated Assembly Time: 45 minutes Tools Required for Assembly (not included): Phillips screwdriver w/medium blade. Leak Detection Solution. ASSEMBLY INSTRUCTIONS 1.
Assembly Instructions ASSEMBLY INSTRUCTIONS 3. Install reflector to support with M8 screws (Qty. 6) 3 Hardware Used 4. Wrap the ceramic rope with clips (RR) around the top and bottom of the Ruby Quartz Glass Tube (E) and attach clips to glass. (fig 4-A) 4-A RR E Then place the Glass tube with both pieces of ceramic rope into glass tube holder at bottom. (fig.
ASSEMBLY INSTRUCTIONS Assembly Instructions 6. Tighten the Nut M8 on the reflector.Then 5. Loosen thetotop nut M8 under use Bolt M8 tighten thex3 small hatthe on top of reflector in clockwise direction. Then lift the the reflector. emitter by one hand and place the glass tube inside. Gently pull downward on the emitter, and tighten the nut M8 x3 under the reflector in a counterclockwise direction.
ASSEMBLY INSTRUCTIONS 7. Align bottom panel on top of base plate and connect them together by securely installing (5) M8×15 screws 7. Align bottom panel on topthrough of basethe plate designated 90 degree metal brackets with a and connect them together by securely philips screwdriver. installing (5) M8×15 screws through the designated 90 degree metal brackets with a philips screwdriver. 7 7 x5 DD Philips Screw M8×15 mm PP x5 x1 screwdriver Philips PP screwdriver x1 8 8 8.
Assembly Instructions ASSEMBLY INSTRUCTIONS 9 .Re-install the protective steel guard(D) by hanging it on the upper support slots.Next tightly secure it with all (12) of the M5×10 screws in to their original support slots accordingly. 9 MM D . Hardware Used MM Screw M5×10 mm x 12 PP Philips screwdriver x1 10. Install regulator to the heater. WARNING! Ensure the hose does not contact anyWrap high gas temperature surfaces, or it(TT) may melt 10. intake with teflon tape and leak, causing a fire.
Assembly Instructions WARNING WARNING Ensure the hose does not contact any high temperature surfaces, or it may melt and leak causing a fire. After the cylinder is placed inside the heater, secure the cylinder with block belt tightly. Ensure the hose does not contact any high temperature surfaces, or it may melt and leak causing a fire. 12. Leak testing: See leak testing diagram for areas to check. Turn all burner controls to the off position. Turn gas supply valve on.
The installation must conform with local codes, or in the absence of local codes,with national fuel gas code, ANSI Z223.1/NFPA54, natural gas and propane Installation Code, CSA B149.1, or propane storage and handling code, B149.2. 13. Install wheel kit to base plate by inserting (2) x Bolt M8 x 15mm through the wheel kit and base plate and securing them with (2) x Nut M8 (use supplied wrench to tighten). WARNING After the cylinder is placed inside the heater, secure the cylinder with block belt tightly.
Operation Instructions OPERATION INSTRUCTIONS 12. Unscrew the switch button, insert AA alkaline battery, tighten the switch button. 1 12 QQ OPERATION INSTRUCTIONS Hardware Used DANGER QQ AA Alkaline Battery &$5%21 0212;,'( +$=$5' x1 )RU RXWGRRU XVH RQO\ 1HYHU XVH LQVLGH KRXVH RU RWKHU XQYHQWLODWHG RU HQFORVHG DUHDV 7KLV KHDWHU FRQVXPHV DLU R[\JHQ 'R QRW XVH LQ XQYHQWLODWHG RU HQFORVHG DUHDV WR DYRLG HQGDQJHULQJ \RXU OLIH OPERATION INSTRUCTIONS AAA Alkaline Battery 1.
Operation Instructions OPERATION INSTRUCTIONS OPERATION INSTRUCTIONS 4. Push the igniter button until pilot flame is visible throughthe glass tube. 5. Once the pilot is lit, continue to depress the control knob for 30 seconds. 6. If the pilot does not stay lit, repeat steps 4 to 6. 7. If after repeating steps 4 to 6 unit does not light, then -Push in control knob and turn counterclockwise to “PILOT” (Figure 3).
Operation Instructions OPERATION INSTRUCTIONS OPERATION INSTRUCTIONS WARNING FOR YOUR SAFETY Be careful when attempting to manually ignite this heater. Holding in the control knob for more than 20 seconds before igniting the gas will cause a ball of flame upon ignition. When heater is ON: The "pilot light" should be blue with yellow top once burner is lit. The flame in the glass tube will be yellow in color.If excessive yellow flame is detected, turn offheater and consult “Troubleshooting” on page 18.
Care And Maintenance CARE AND MAINTENANCE CARE AND MAINTENANCE Gas odor Heater does NOT reach the desired temperature. Heater glow is excessively uneven. Heater makes popping noises. Spiders and insects can nest in burner or orifices. This dangerous condition can damage heater and render it unsafe for use. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may help clear away smaller particles. Carbon deposits may create a fire hazard.
Troubleshooting & Warranty TROUBLESHOOTING PROBLEM Pilot will not light Note: heater operates at reduced efficiency below 40º (5ºC) Pilot will not stay on Burner will not light Burner flame is low Carbon build-up Thick black smoke PROBABLE CAUSE CORRECTIVE ACTION Gas valve may be OFF Turn the gas valve ON Tank fuel empty Refill LPG tank Opening blocked Clean or replace opening Air in supply system Purge air from lines Debris around pilot Clean dirty area Loose connections Tighten connections
5016039
