Round Flame Tower Heater OH-R744S-Stainless Steel OH-R744B-Heritage Bronze OH-R744BL-Black 5016039 CSA/ANSI 83.26-2020 CSA 2.
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. This manual contains important information about the assembly, operation and maintenance of this patio heater. General safety information is presented in these first few pages and is also located throughout the manual. Keep this manual for future reference and to educate new users of this product. This manual should be read in conjunction with the labeling on the product.
DANGER DANGER • EXPLOSION - FIRE HAZARD • CARBON MONOXIDE HAZARD • Never store propane near high heat, open flames, direct sunlight, other ignition sources or where temperatures exceed 120 degrees F (49°C). • This heater is a combustion appliance. All combustion appliances produce carbon monoxide (CO) during the combustion process. This product is designed to produce extremely minute, non-hazardous amounts of CO if used and maintained in accordance with all warnings and instructions.
WARNING WARNING • Alert children and adults to the hazards of high surface temperatures. Stay away from these surfaces to avoid burning skin or igniting clothing. • Carefully supervise young children when in the vicinity of the heater. • Do not hang clothing or any other flammable materials from the heater, or place on or near the heater. • Replace any guard or protective device removed for servicing the appliance prior to placing back in service.
Parts List PACKAGE CONTENTS AA A B PART DESCRIPTION QUANTITY AA Reflector Cover 1 A Reflector 1 B Emitter 1 C Support 3 D Protective Guard 3 E Ruby Quartz Glass Tube 1 F Burner Ignition Plate 1 G Control Box Casing 1 H Gas Hose & Regulator 1 I Back Panel 1 J Front Door Panel 1 K Wheel Kit 1 L Base Plate 1 C D E F G H I J K L INCLUDED HARDWARE OO EE Wrench Qty. 1 Bolt M8 x 15mm Qty. 2 HH DD QQ Philips screwdriver Qty.
Assembly Instructions PREPARATION Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents above. If any part is missing or damaged, do not attempt to assemble the product. Contact customer service for replacement parts. Estimated Assembly Time: 45 minutes Tools Required for Assembly (not included): Phillips screwdriver w/medium blade. Leak Detection Solution. ASSEMBLY INSTRUCTIONS 1.
Assembly Instructions ASSEMBLY INSTRUCTIONS 3. Install reflector to support with M8 screws (Qty. 6) 3 Hardware Used 4. Wrap the ceramic rope with clips (RR) around the top and bottom of the Ruby Quartz Glass Tube (E) and attach clips to glass. (fig 4-A) 4-A RR E Then place the Glass tube with both pieces of ceramic rope into glass tube holder at bottom. (fig.
Assembly Instructions 6. Tighten the Nut M8 on the reflector.Then 5. Loosen thetotop nut M8 under use Bolt M8 tighten thex3 small hatthe on top of reflector in clockwise direction. Then lift the the reflector. emitter by one hand and place the glass tube inside. Gently pull downward on the emitter, and tighten the nut M8 x3 under the reflector in a counterclockwise direction.
ASSEMBLY INSTRUCTIONS 7. Align bottom panel on top of base plate and connect them together by securely installing (5) M8×15 screws 7. Align bottom panel on topthrough of basethe plate designated 90 degree metal brackets with a and connect them together by securely philips screwdriver. installing (5) M8×15 screws through the designated 90 degree metal brackets with a philips screwdriver.
Assembly Instructions ASSEMBLY INSTRUCTIONS 9 .Re-install the protective steel guard(D) by hanging it on the upper support slots.Next tightly secure it with all (12) of the M5×10 screws in to their original support slots accordingly. 9 MM D . Hardware Used MM Screw M5×10 mm x 12 PP Philips screwdriver x1 10. Install regulator to the heater. WARNING! Ensure the hose does not contact anyWrap high gas temperature surfaces, or it(TT) may melt 10. intake with teflon tape and leak, causing a fire.
Assembly Instructions WARNING WARNING Ensure the hose does not contact any high temperature surfaces, or it may melt and leak causing a fire. After the cylinder is placed inside the heater, secure the cylinder with block belt tightly. Ensure the hose does not contact any high temperature surfaces, or it may melt and leak causing a fire. 12. Leak testing: See leak testing diagram for areas to check. Turn all burner controls to the off position. Turn gas supply valve on.
The installation must conform with local codes, or in the absence of local codes,with national fuel gas code, ANSI Z223.1/NFPA54, natural gas and propane Installation Code, CSA B149.1, or propane storage and handling code, B149.2. 13. Install wheel kit to base plate by inserting (2) x Bolt M8 x 15mm through the wheel kit and base plate and securing them with (2) x Nut M8 (use supplied wrench to tighten).
Operation Instructions OPERATION INSTRUCTIONS Caution: Do not attempt to operate until you have read and understand all General Safety Information in this manual and all assembly is complete and leak checks have been performed. %HIRUH 7XUQLQJ *DV 6XSSO\ 21
Operation Instructions OPERATION INSTRUCTIONS OPERATION INSTRUCTIONS The 2 seconds delay ignition is not a flaw. It has been intentionally designed to prevent accidental ignition. Holding the POWER button for 2 seconds releases the safety lock and starts the ignition. WARNING TO TURN OFF THE HEATER 1. Press POWER button again to enter into close status 2. Turn off the valve of the gas cylinder and disconnect the cylinder. 1. Close the valve of the gas cylinder or the regulator after use. 2.
Care And Maintenance CARE ANDINSTRUCTIONS MAINTENANCE OPERATION Re-lighting: 1.Press POWER button again to enter into close status 2. Wait at least 5 minutes, to let gas dissipate, before attempting to relight POWER. Flash out will happen if performed before 5 minutes are up . 3. Repeat the “Lighting” steps on prior page. WARNING 1.Change the gas cylinder in a amply ventilated area, away from any ignition source (candle, cigarettes, other flame producing appliances, ...) 2.
Care And Maintenance CARE AND MAINTENANCE CARE AND MAINTENANCE 9. Heater is away from gasoline or other flammable liquids or vapors. 10. Heater is away from windows, air intake openings, sprinklers and other water sources. 11. Heater is at least 2.3 feet on top and at least 3.3 feet on sides from combustible materials. 12. Heater is on a hard and level surface. 13. There are no signs of spider or insect nests. 14. All burner passages are clear. 15. All air circulation passages are clear. 16.
Care And Maintenance CARE AND MAINTENANCE CARE AND MAINTENANCE Visually checking portions of the hose assembly located within the confines of the heater post. Inspect the entire hose assembly at least annually, disassembling the reflector and burner. Inspect the hose assembly for evidence of excessive abrasion, cuts, or wear. Suspected areas should be leak tested. Gas odor with extreme yellow tipping of flame. Heater does NOT reach the desired temperature. Heater glow is excessively uneven.
Troubleshooting & Warranty TROUBLESHOOTING PROBLEM PROBABLE CAUSE SOLUTION There is no spark at pilot when the heater is started Igniter electrode positioned wrong. Igniter electrode broken. Igniter cable pinched or broken. Burner ceramic plate is broken of faulty. There is spark but no ignition when the heater is started Adjust the distance of the electrode and ignition device to 5 mm Replace. Free electrode cable. Replace if damaged. Replace ceramic plate.
5016039