Router User's Guide

ManualsBrandsParadyne ManualsNetwork Router9126

141

142

143

144

145

146

147

148

149

150

Table Of Contents

Contents
About This Guide
- Purpose and Intended Audience
- Document Organization
- Product-Related Documents
- Conventions Used
1. About the FrameSaver SLV
- System Overview
  - CSU/DSU-Specific Features
  - Router-Specific Features
- FrameSaver Diagnostic and SLM Feature Sets
- FrameSaver Diagnostic Feature Set
  - Additional FrameSaver SLV 9126-II and 9128-II Features
  - Additional FrameSaver SLV 9128-II Features
- FrameSaver SLM Feature Set
- OpenLane SLM System
- NetScout Manager Plus and NetScout Probes
2. User Interface and Basic Operation
- Logging On
- Main Menu
- Screen Work Areas
- Navigating the Screens
- Navigating the Router’s CLI
  - CLI Keyboard Keys
3. Configuration Procedures
- Basic Configuration
4. Configuration Options
- Using the Easy Install Feature
- Using RIP with FrameSaver SLV CSU/DSUs
- Entering System Information and Setting the System Clock
- Setting Up the Modem
  - Setting Up Call Directories for Trap Dial-Out
  - Setting Up to Use the Modem PassThru Feature
- Setting Up Auto-Configuration
  - Selecting a Frame Relay Discovery Mode
  - Automatically Removing a Circuit
- Setting Up Dial Backup
- PVC Backup Over the Network Interface
- Setting Up Back-to-Back Operation
  - Changing Operating Mode
- Configuration Option Tables
- Configuring the Overall System
- Configuring Physical Interfaces
- Assigning Time Slots/Cross Connections
- Configuring Frame Relay for an Interface
- Manually Configuring DLCI Records
- Configuring PVC Connections
- Configuring the IP Path List
- Setting Up Management and Communication Options
- Configuring the Criteria for Automatic Backup
5. Configuring the FrameSaver SLV Router
- FrameSaver SLV Router Overview
- IP Routing
- Address Resolution Protocol
- Proxy ARP
- Interface Configuration
- Network Address Translation
- Network Address Port Translation
  - NAPT Configuration Example
  - NAT and NAPT Configuration Example
- Dynamic Host Configuration Protocol Server
  - DHCP Server with NAT Configuration Example
  - DHCP Server at Remote Site Configuration Example
- DHCP Relay Agent
- Router Security
- Provisioning the Router Interface
- Configuring the Router Using Terminal Emulation
  - Uploading and Downloading the Router Configuration Via the CLI
6. Security and Logins
- Limiting Access
- Controlling Asynchronous Terminal Access
- Limiting Dial-In Access via the Modem Port
- Controlling ISDN Access
  - ISDN Call Security
  - Disabling ISDN Access
- Controlling Telnet or FTP Access
- Controlling SNMP Access
- Creating a Login
- Modifying a Login
- Deleting a Login
- Controlling Router CLI Access
  - Access Levels (Command Modes)
  - Changing Access Levels
7. Operation and Maintenance
- Displaying System Information
- Viewing LEDs and Control Leads
- Device Messages
- Status Information
- IP Routing Table
- Performance Statistics
- Trap Event Log
- Modem Operation
- ISDN DBM Operation
- FTP File Transfers
- Turning Off the System Alarm Relay
8. Troubleshooting
- Problem Indicators
- Resetting the Unit and Restoring Communication
- Troubleshooting Management Link Feature
- LMI Packet Capture Utility Feature
  - Viewing Captured Packets from the Menu-Driven User Interface
- Alarms
- Viewing the Trap Event Log
- Troubleshooting Tables
- Tests Available
  - Test Timeout Feature
  - DBM Tests
- Starting and Stopping a Test
  - Aborting All Tests
- PVC Tests
- Physical Tests
- IP Ping Test
  - IP Ping Test – Procedure 1
  - IP Ping Test – Procedure 2
- Lamp Test
9. Setting Up OpenLane for FrameSaver Devices and Activating SLM Features
- OpenLane Support of FrameSaver Devices
- Setting Up the OpenLane SLM System
- Setting Up FrameSaver Support
- Ordering SLM Feature Set Activations
  - To Find Your License Key Number
  - The Activation Certificate
- Administering and Managing SLM Activations
10. Setting Up NetScout Manager Plus for FrameSaver Devices
- Preparation
- Configuring NetScout Manager Plus
- Monitoring a DLCI’s History Data
- Monitoring the Agent Using NetScout Manager Plus
- Statistical Windows Supported
11. Setting Up Network Health for FrameSaver Devices
- Installation and Setup of Network Health
- Discovering FrameSaver Elements
- Configuring the Discovered Elements
- Grouping Elements for Reports
- Generating Reports for a Group
- Reports Applicable to SLV Devices
A. Menu Hierarchy
- Menus
B. SNMP MIBs and Traps, and RMON Alarm Defaults
- MIB Support
- Downloading MIBs and SNMP Traps
- System Group (mib-2)
  - FrameSaver Unit’s sysDescr (system 1)
  - FrameSaver Unit’s sysObjectID (system 2)
- Interfaces Group (mib-2)
  - Paradyne Indexes to the Interface Table (ifTable)
  - NetScout Indexes to the Interface Table (ifTable)
- Standards Compliance for SNMP Traps
- RMON Alarm and Event Defaults
- Object ID Cross-References (Numeric Order)
C. Router CLI Commands, Codes, and Designations
- CLI Commands
- Ethernet Type Codes
- Protocol and Port Designations
D. Router Command Line Summaries and Shortcuts
- CLI Summaries
E. Connectors, Cables, and Pin Assignments
- Rear Panels
- COM Port Connector
- DTE Port Connector
  - Standard V.35 Straight-through Cable
  - Standard V.35 Crossover Cable
- DSX-1 Connector
- T1 Network Cable (Feature No. 3100-F1-500)
  - T1 Mass Termination Cable (Feature No. 9007-F1-500)
  - Canadian T1 Line Interface Cable (Feature No. 3100-F1-510)
- Ethernet Port Connector
- Modem Connector
- ISDN DBM Connector
  - ISDN Modular Cable
F. Technical Specifications
G. Equipment List
- Equipment
- Cables
Index
- Numerics
- A
- B
- C
- D
- E
- F
- G
- H
- I
- K
- L
- M
- N
- O
- P
- Q
- R
- S
- T
- U
- V
- W
- Y

4. Configuration Options

9128-A2-GB20-80 September 2002

4-99

IP Address

Possible Settings: 001.000.000.000 – 223.255.255.255, Clear

Default Setting: Clear (000.000.000.000)

Specifies a unique IP address for accessing the unit via the COM port. Only in effect when

the COM port is configured as a network communication link (Port Use option is set to Net

Link).

Display Conditions

– This option only appears when Port Use is set to Net Link.

001.000.000.000 – 223.255.255.255 – Shows the IP address for the COM port, which you

can view or edit.

Clear – Clears the IP address for the COM port and fills the address with zeros. When the

IP Address is all zeros, the COM port uses the Node IP Address if one has been

configured.

Subnet Mask

Possible Settings: 000.000.000.000 – 255.255.255.255, Clear

Default Setting: 000.000.000.000

Specifies the subnet mask needed to access the unit. Only in effect when the COM port is

configured as a network communication link (Port Use option is set to Net Link).

Display Conditions

– This option only appears when Port Use is set to Net Link.

000.000.000.000 – 255.255.255.255 – Shows the subnet mask for the COM port, which

you can view or edit.

Clear – Clears the subnet mask for the COM port and fills the address with zeros. When

the node subnet mask is all zeros, the IP protocol creates a default subnet mask based

upon the class of the IP address: Class A: 255.000.000.000, Class B: 255.255.000.000, or

Class C: 255.255.255.000.

RIP

Possible Settings: None, Standard_out

Default Setting: None

Specifies which Routing Information Protocol (RIP) is used to enable routing of

management data between devices.

Display Conditions

– This option only appears when Port Use is set to Net Link.

None – No routing is used.

Standard_out – The device will send standard RIP messages to communicate routing

information about other FrameSaver units in the network. Standard RIP messages

received on this link are ignored.

NOTE: The router must be configured to receive RIP on the port connected to the

COM port, configured as the management interface (e.g., Cisco:

config-t, router

RIP, int serial

, IP RIP Receive version 1, ctl-z WR

To create this management interface, make sure that Node or COM port IP Information

has been set up (see

Configuring Node IP Information

on page 4-74).

Table 4-24. Communication Port Options (4 of 5)