User's Manual

ManualsBrandsParadox Security Systems ManualsElectronicsWireless Siren with Built-in Strobe

FCCSR150-EI08 09/2009 SR150 V2.0 PARADOX.COM

Programming

Upgrading the Firmware

The SR150 firmware can be upgraded through WinLoad using the 307USB Direct Connect Interface. Refer to the firmware upgrade

instructions found at: paradox.com - Software - WinLoad -Firmware Upgrade Instructions.

NOTE: Ensure that the SR150 Wireless Siren is awake before beginning the firmware upgrade. To wake up the siren, press the “test’

button. The siren will provide you with a 60 second delay in order to begin the update.

Siren Supervises Panel/RTX3

The SR150 supervises the control panel and the RTX3 every 12 minutes (with external power supply) or every 25 minutes (with battery

power only). If after 3 attempts SR150 Wireless does not receive a response, the siren will squawk every 4 seconds and the strobe light

will flash every 4 second for a period of 5 minutes. When this occurs, the siren/strobe can be stopped by pressing the disarm button on

any of the first 10 remotes assigned to the system.

Tamper Supervision

If a tamper is detected, the SR150 will sound an alarm and the strobe light will flash for 4 minutes. The control panel will follow the global

supervision options set in the panel.

For complete warranty information, please visit www.paradox.com/terms. Your use of the Paradox product signifies your acceptance of all warranty terms and conditions. Magellan, Spectra SP, EVO, and

WinLoad are trademarks or registered trademarks of Paradox Security Systems Ltd. or its affiliates in Canada, the United States and/or other countries. For the latest product approvals, such as UL and CE,

6215399, 6111256, 6104319, 5920259, 5886632, 5721542, 5287111, 5119069, 5077549 and RE39406 and other pending patents may apply. Canadian and international patents may also apply.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

LED Feedback Specifications

Power 4.5Vdc (3 size “D” alkaline batteries)

Optional: 8-16Vac / 9-20Vdc external power

Battery life Up to 3 years based on normal use (e.g. 2 alarms per

year with strobe for 2.5 hours and 8 squawks per day

at an average of 25

ºC (77ºF). Using optional power

source will extend battery life.

Consumption Sleep: 22uA, Standby: 130uA, Alarm: 550mA

RF frequency 433MHz or 868MHz

Siren 100dB (1 meter)

Dimensions 24cm X 6.cm X 18cm (9.5in X 2.3in X 7in)

Operating

Temperature

Battery only: -30ºC to 50ºC (-22ºF to 122ºF)

RF range 70m (229ft)

MG/SP Feature Details

[683] Learn Siren #1 Press and hold “TEST” switch for 3 seconds after entering the

section to learn the siren. Warning: When you press the “TEST”

switch, the SR150 will squawk and the strobe light will flash five

times to confirm registration to the panel.

[684] Learn Siren #2

[685] Learn Siren #3

[686] Learn Siren #4

[687] Display Signal Strength Siren #1 Press and hold “Test” switch for 3 seconds after entering the

section to display, on a K32LCD V1.3 or higher, the signal

strength the panel is receiving from the siren.

[688] Display Signal Strength Siren #2

[689] Display Signal Strength Siren #3

[690] Display Signal Strength Siren #4

[691] Label Siren #1 These labels are used when reporting events via e-mail through

the IP100 and for troubleshooting purposes. Maximum 16

characters.

[692] Label Siren #2

[693] Label Siren #3

[694] Label Siren #4

[695] Temporary Tamper Switch Deactivation

for Maintenance

Press the [

ENTER] key after entering the section to deactivate

tamper alarm until the cover is replaced or after 30 minutes.

[587] Panel Supervision of Siren OFF = disabled ON = enabled (default)

Option [3] Siren #1 (OFF/ON) The control panel supervises the presence of the SR150. If lost,

the control panel will follow global supervision loss option set in

the panel.

Option [4] Siren #2 (OFF/ON)

Option [5] Siren #3 (OFF/ON)

Option [6] Siren #4 (OFF/ON)

TX Sending data

RX Receiving data

PSSI Signal strength siren is receiving from panel

Flash 4x - strong signal

Flash 3x - good signal

Flash 2x - weak signal

Flash 1x - very weak signal (relocate)

No flash - no signal

Status Flash once/sec. - Processor is on

Flash once/4 sec. - Power save mode

Remove cover to view

LED status