Installation Manual

RTX3-EI14 04/2019PARADOX.COM
PGM Programming for EVO
This applies to EVO panels version 6.90 and below.
1. Enter section [0901] - [0932].
2. Enter the 8-digit serial number and 3-digit output number.
3. Enter the 3-digit Event Group, Feature Group, Start # and End # for PGM
activation.
4. Enter the 3-digit Event Group, Feature Group, Start #, and End # for PGM
deactivation.
5. Define the PGM Delay Value (001 to 255 x 1 sec./min.). Default set to 15
minutes.
6. Set your PGM options, refer to the table below.
PGM Option Programming for EVO
The following options apply to sections [919], [929]...[989]:
Option [1]: PGM deactivation after, refer to table.
Option [2]: PGM Base Time: On = minutes; Off = seconds (default)
Option [8]: Flexible PGM deactivation**, refer to table
* For a complete list of events, refer to the PGM programming section of your
EVO Programming Guide.
** In order to use the “Flexible PGM deactivation” option [8], the PGM deactivation
after option [1] must be ON.
Firmware Upgrade
Upgrade RTX3 firmware using a serial connection (307USB). For firmware
upgrade instructions see the Firmware Upgrade Instructions document at:
Paradox.com > Software > BabyWare.
Hardware Compatibility
Technical Specifications
FCCandIndustryCanadaComplianceStatement
This device complies with FCC Rules Part 15 and with Industry Canada license exempt RSS stan-
dard(s). Operation is subject to two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference that may be received or that may cause undesired
operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
1. l'appareil ne doit pas produire de brouillage, et
2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.
FCC ID: KDYRTX3
IC: 2438A-RTX3
FCC WARNING
This equipment has been tested and found to comply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party responsible for com-
pliance (Paradox Security Systems Ltd.) could void the user’s authority to operate the equipment.
[601] to
[632]
Transmitter signal
strength
[601] = Zone input 1
[632] = Zone input 32
• 3 or less: weak (move transmitter)
• 4 to 10: OK
[701] to
[732]
Current battery life [701] = Zone input 1
[732] = Zone input 32
View number of weeks the batteries have
been in the transmitter
[801] to
[832]
Previous battery life [801] = Zone input 1
[832] = Zone input 32
View number of weeks the previous
batteries were in the transmitter
[671] to
[678]
2WPGM Signal Strength Sections [671]-[678] correspond to Zone
inputs 1 - 8
Signal Strength:
• 3 or less: weak (move transmitter)
• 4 to 10:
OK
[991] View two-way PGM Tam-
per Trouble
PGM # in tamper trouble is displayed
[992] View two-way PGM
Supervision Trouble
PGM # in supervision trouble is displayed
[901] to
[908]
Assign 2WPGMs Sections [901]-[908] correspond to Zone
inputs 1 - 8
To assign 2WPGMs:
Enter a 6-digit serial number or press and
release the transmitter’s tamper switch
To delete an assigned 2WPGM:
Enter 000000 as a serial number
Note: If a section between [901] to [904]
is empty, the RTX3 uses the on board
PGM
OPTION DESCRIPTION
PGM #
OFF ON
1
PGM deactivation after (OFF = deactivation
event; ON = PGM timer)
 
2
PGM base time (OFF = seconds;
ON = minutes)
 
3
Flexible PGM deactivation option
(OFF = PGM timer only; ON = PGM timer and/
or deactivation event)
 
4
PGM initial state (OFF = normally open;
ON = normally closed)
 
5
PGM time base (OFF = follow option 2,
ON = hour)
 
6 to 8
Future use
--
Section Feature Details
PGM Activation*
Event Group Feature
Group
Start # End #
PGM1
[910] [911] [912] [913]
PGM2
[920] [921] [922] [923]
PGM3
[930] [931] [932] [933]
PGM4
[940] [941] [942] [943]
PGM5
[950] [951] [952] [953]
PGM6
[960] [961] [962] [963]
PGM7
[970] [971] [972] [973]
PGM8
[980] [981] [982] [983]
Default Data
000 000 000 000
PGM Deactivation*
Event Group Feature
Group
Start # End #
PGM1
[914] [915] [916] [917]
PGM2
[924] [925] [926] [927]
PGM3
[934] [935] [936] [937]
PGM4
[944] [945] [946] [947]
PGM5
[954] [955] [956] [957]
PGM6
[964] [965] [966] [967]
PGM7
[974] [975] [976] [977]
PGM8
[984] [985] [986] [987]
Default Data
000 000 000 000
PGM Delay
Delay (000 to 255) Options
PGM1
[918] [919]
PGM2
[928] [929]
PGM3
[938] [939]
PGM4
[948] [949]
PGM5
[958] [959]
PGM6
[968] [969]
PGM7
[978] [979]
PGM8
[988] [989]
Default Data
005 OFF
[1]
[8] Details
OFF
OFF Deactivation event
OFF
ON Deactivation Event
ON
OFF PGM Timer
ON
ON PGM Timer or Deactivation event
EVO SP Series
Zones
32 32
Remotes
32/999 32
Remote Control Type
REM1
RAC1
REM2
REM3
REM15
REM25
Wireless PGMs
816
Wireless Keypads
-8
Wireless Siren
84
Wireless Repeater
-2
Power input voltage
12 Vdc
Frequency
433 or 868 MHz selectable
Sensitivity
-120 dBm
Current consumption
50 mA
Dimensions and weight
15 x 16 x 3 cm (6 x 6 x 1.1 in.) / 24g
Operating temperature
0°C to 49°C (32°F to 120°F)
Humidity
5 - 90%
PGM outputs
PGM1 and PGM2 - 150mA PGM transistor out-
puts
PGM3 - Form C relay output rated at 5A/28Vdc,
N.O./N.C. (PGM4 optional)
Range
Refer to the appropriate transmitter instructions
Other
Di-pole antenna; error correction algorithm
Approvals
CE, EN 50131-1 and EN 50131-3,
Security Grade 2, Environmental Class II
Warranty
For complete warranty information on this product, please refer to the Limited Warranty Statement
which can be found on paradox.com/terms or contact your local distributor.
Patents
US, Canadian and international patents may apply. Paradox is a trademark or registered trademark of
Paradox Security Systems (Bahamas) Ltd.
©2019 Paradox Security Systems (Bahamas) Ltd. All rights reserved. Specifications may change
without prior notice.