User's Manual
Table Of Contents
- Basic Operations
- Programming Access Codes
- System Master Code (Default: 123456)
- Master Codes
- Duress Code
- Programming Access Codes
- 2. Enter your [system master code] or either [master code].
- 3. The [] key will flash. When a zone LED or zone key is lit (not flashing), the user is already programmed.
- 4. Select a user by entering a 2-digit user number (i.e. [0]+[9] for user 9) or use the scroll keys and then press [enter]. For the MG10LEDV/H, press the key corresponding to the user number (i.e. [9] for user 9).
- 5. Enter a new 4- or 6-digit [access code].
- 6. Confirm the code.
- 7. Press a button on the designated remote or press [enter] to skip if there is no remote to program.
- 8. (Not available for non-partitioned system) Press [1] and/or [2] to assign the user to a partition. Press [enter], the menu will now jump to the next available user, if you choose to continue.
- 2. Enter your [system master code] or either [master code].
- 3. Select a user by entering a 2-digit user number (i.e. [0]+[9] for user 9). For the MG10LEDV/H, enter a 1-digit user number (i.e. [9] for user 9).
- 4. Press the [sleep] key until you hear the confirmation beep.
- Regular Arming
- Sleep Arming
- Stay Arming
- One-Touch Arming
- Auto-Arming
- Timed Auto Arming
- 2. Enter [master code].
- 3. Press the [byp] key. The [byp] key will flash to indicate you are in the System Options menu.
- 4. Press key [1] to set partition 1, or press key [2] to set partition 2.
- 5. Enter the desired time for auto arm (24 hour clock, e.g. 18:30).
- 6. Press key [1] to regular arm, key [2] to sleep arm, or key [3] to stay arm the partition.
- No Movement Auto Arming
- Timed Auto Arming
- Disarming & Deactivating an Alarm
- 2. Press [off] + enter [access code].
- 3. If you have access to both partitions (see Partitioning on page 3): Press the key corresponding to the desired partition ([1] or [2]). For both partitions, press the other key after the confirmation beep.
- Manual Bypass Programming
- 2. Enter your [access code] (see the note below). The [byp] key will flash.
- 3. Illuminate the number(s) corresponding to the zone(s) you want to bypass by entering the two-digit zone number (i.e. zone 3 = 03). Solid on = Zone open, Flash = Zone bypass, Off = Zone closed, not bypassed.
- 4. Press the [enter] key to save and exit.
- Bypass Recall Feature
- Display Mode
- Alarm Display
- Fire Alarms
- Panic Alarms
- Programming Chime Zones
- Keypad Muting
- Keypad Backlight
- PGM Keys (Programmable Outputs)
- Power Save Mode
- Trouble Display
- 2. Read the corresponding explanation of the trouble from the Trouble List below. If no repair instructions are given, call your monitoring station for repairs.
- 3. Press the [clear] key to exit.
- Trouble List
- 2. Enter the hour and minutes. If the hour is between 01 and 12, you will need to select [1] for 24Hr format, [2] for AM, and [3] for PM setting. If the hour is above 12, the system will automatically select the 24Hr format.
- 3. Enter the year (4 digits).
- 4. Enter the month (2 digits).
- 5. Enter the day (2 digits). You have now set the Time & Date. Press [clear] to exit.
- Quick Function Keys
- Testing & Maintenance
- System Checklist
- Master Quick Menu MG5000
- Overview
- User
- PGMs
- PGM Utility Keys
- System Timers
- Other Information
- Access Codes
- 2. The [] key will flash. When a zone LED or zone key is lit (not flashing), the user is already programmed.
- 3. Select a user by entering a 2-digit user number (i.e. [0]+[9] for user 9) or use the scroll keys and then press [enter]. For the MG10LEDV/H, press the key corresponding to the user number (i.e. [9] for user 9).
- 4. Enter a new 4- or 6-digit [access code].
- 5. Confirm the code.
- 6. Press a button on the designated remote or press [enter] to skip if there is no remote to program.
- 7. (Partitioned system only) Press [1] and/or [2] to assign the user to a partition. Press [enter], the menu will now jump to the next available user.
4 User Guide
Access Codes
Programming Access Codes
Access codes are personal identification numbers that allow you to enter certain programming modes, arm or disarm your system as well
as activate or deactivate PGMs. The Magellan security system supports the following:
• 1 System Master Code
• 2 Master Codes
• 29 User Access Codes
For information on how each access code can arm or disarm the system refer to the System Checklist on page 13 and 14.
System Master Code (Default: 123456)
The System Master Code can arm or disarm any partition using any of the methods described in this section and can create, modify
or delete any user access code (see Programming Access Codes below).
Master Codes
Master Code 1 is permanently assigned to Partition 1 and can be used to create, modify or delete user access codes (see
Programming Access Codes below) that are assigned to Partition 1.
Master Code 2 is permanently assigned to Partition 2 (except when partitioning is disabled, Master Code 2 will be assigned to
Partition 1) and can be used to create, modify or delete user access codes that are assigned to the same partition.
Master Codes cannot modify or delete user access codes assigned to both partitions. Only the System Master Code can modify or delete
user access codes assigned to both partitions.
Duress Code
If you are forced to arm or disarm your system, entering the access code with the duress option enabled will arm or disarm the
system and immediately transmit a silent alert (Duress Code) to the monitoring station.
Must be enabled by your installer.
Programming Access Codes
Your system can use either 4- or 6-digit access codes, where each digit can be any value from 0 to 9. Six-digit codes are considered
more difficult to “crack” and therefore, more secure. Avoid programming simple or obvious access codes, such as your telephone
number, address or codes such as 1234. Also, see the Master Quick Menu at the end of the manual (page 17-18).
How do I program Access Codes?
1. Press the [] key.
2. Enter your [
SYSTEM MASTER CODE] or either [MASTER CODE].
3. The [] key will flash. When a zone LED or zone key is lit (not flashing), the user is already programmed.
4. Select a user by entering a 2-digit user number (i.e. [0]+[9] for user 9) or use the scroll keys and then press [
ENTER]. For the
MG10LEDV/H, press the key corresponding to the user number (i.e. [9] for user 9).
5. Enter a new 4- or 6-digit [
ACCESS CODE].
6. Confirm the code.
7. Press a button on the designated remote or press [
ENTER] to skip if there is no remote to program.
8. (Not available for non-partitioned system) Press [1] and/or [2] to assign the user to a partition. Press [
ENTER], the menu will
now jump to the next available user, if you choose to continue.
How do I delete Access Codes?
1. Press the [] key.
2. Enter your [
SYSTEM MASTER CODE] or either [MASTER CODE].
3. Select a user by entering a 2-digit user number (i.e. [0]+[9] for user 9). For the MG10LEDV/H, enter a 1-digit user number (i.e.
[9] for user 9).
4. Press the [
SLEEP] key until you hear the confirmation beep.