Installation Instructions

14 Reference & Installation Manual
5.5.1 Entry Delay 1
Sections [001] to [015]: Zones 1 to 15, First Digit = 1
When the system is armed and a zone defined with Entry Delay 1 opens, the control panel will generate an alarm after
the programmed Entry Delay 1 Timer elapses. This is to provide users with enough time to enter the protected area
and disarm the system. To program the Entry Delay 1 Timer, key in the desired 3-digit delay value (000 to 255
seconds, Default = 45 seconds) into section [069]. Entry delay zones are commonly used at the entry/exit points of the
protected area (i.e. front/back door, garage, etc.). Using different entry delays (see Entry Delay 2 on page 14) is useful
when, for example, one entry point requires a longer delay than the other entry point or in a partitioned system where
each partition may require a different entry delay.
5.5.2 Entry Delay 2
Sections [001] to [015]: Zones 1 to 15, First Digit = 2
Entry Delay 2 zones are identical to the Entry Delay 1 zones (see section 5.5.1), except it uses a separate entry delay
timer. To program the Entry Delay 2 Timer, key in the desired 3-digit delay value (000 to 255 seconds, Default = 45
seconds) into section [070].
This timer is also used as the Stay Delay timer (see Stay Arming with Delay on page 22).
5.5.3 Follow Zones
Sections [001] to [015]: Zones 1 to 15, First Digit = 3
When an armed Follow Zone opens, the control panel will immediately generate an alarm, unless an entry delay zone
opens first:
• If an armed Follow Zone opens after an entry delay zone opens, the control panel waits until the entry delay timer
has elapsed before generating an alarm.
• If an armed Follow Zone opens after more than one entry delay zone opens, the control panel will wait until the
entry delay timer of the zone that opened first has elapsed.
This feature is commonly used when a motion detector is protecting the area occupied by the entry point keypad. This
will prevent the motion detector from causing an alarm when a user enters through the entry point to disarm the
system.
5.5.4 Instant Zones
Sections [001] to [015]: Zones 1 to 15, First Digit = 4
When an armed Instant Zone opens, the control panel immediately generates an alarm. Instant Zones are commonly
used for windows, patio doors, skylights and other perimeter type zones.
5.5.5 24Hr Burglary Zones
Sections [001] to [015]: Zones 1 to 15, First Digit = 5
Whenever a 24Hr Burglary Zone opens, whether the system is armed or disarmed, the control panel will immediately
generate an alarm.
5.5.6 24Hr Buzzer
Sections [001] to [015]: Zones 1 to 15, First Digit = 6
Whenever a 24Hr Buzzer Zone opens, whether the zone is armed or disarmed, the control panel sets off the keypad’s
buzzers to indicate that the zone was breached. The control panel will report the alarm, but will not enable the bell/
siren output. Enter any valid access code on the keypad to stop the buzzer. This zone definition is particularly useful
when a user wishes to be notified when something such as a safe or locker within the home has been accessed
(i.e. a child accessing a valuable collection).
5.6 Exclusive Zone Definitions
The following three zone definitions can only be used for devices connected directly to the control panel’s on-board input
terminals. When a zone is programmed as a keyswitch zone, the control panel will ignore all other Zone Options. When a zone is
programmed as a standard fire zone or delayed fire zone, the control panel will ignore the Zone Options that may have been
programmed, except Auto Zone Shutdown. Wireless devices and devices connected to the zone expansion bus modules cannot
be programmed with these definitions.
5.6.1 Keyswitch Zone
Sections [001] to [005]: Zones 1 to 5, First Digit = 7
Connecting a keyswitch to a zone allows users to arm the system by pressing a button or by turning a switch on or off
with a key. Please refer to Keyswitch Connections on page 6 and Keyswitch Options on page 17.