User's Manual
Table Of Contents
- Table of Contents
- Part 1: Introduction
- Part 2: Installation
- Part 3: Programming Methods
- Part 5: Zone Programming
- Part 7: Arming and Disarming Options
- 7.1 Switch To Stay Arming
- 7.2 Stay Arming with Delay
- 7.3 Regular Arming switches to Force Arming (Not to be used with UL Installations)
- 7.4 Restrict Arming On Battery Fail
- 7.5 Restrict Arming On Tamper Failure
- 7.6 Timed Auto-Arming
- 7.7 No Movement Auto-Arming
- 7.8 Auto-Arming Options (Not to be used with UL installations)
- 7.9 One-Touch Arming (Not to be used with UL installations)
- 7.10 Exit Delay
- 7.11 Bell Squawk On Arm/Disarm With Keypad
- 7.12 Bell Squawk On Arm/disarm with Remote Control
- 7.13 No Exit Delay When Arming with Remote Control
- 7.14 No Exit Delay Beeps and No Bell Squawk When Stay Arming
- Part 8: Alarm Options
- Part 9: Reporting and Dialer settings
- 9.1 Reporting/Dialer (Enable/Disable)
- 9.2 Report Codes
- 9.3 Central Station Telephone Numbers
- 9.4 Partition Account Numbers
- 9.5 Reporting Formats
- 9.6 Pager Delay
- 9.7 Event Call Direction
- 9.8 Dialing Method
- 9.9 Pulse Ratio
- 9.10 Bell on Communication Failure
- 9.11 Dial Tone Delay
- 9.12 Maximum Dialing Attempts
- 9.13 Delay Between Dialing Attempts
- 9.14 Alternate Dial Option
- 9.15 Recent Close Delay
- 9.16 Auto Test Report
- 9.17 Power Failure Report Delay
- 9.18 Disarm Reporting Options
- 9.19 Zone Restore Report Options
- 9.20 Telephone Line Monitoring (TLM)
- Part 10: Programmable Outputs
- Part 11: System Settings
- 11.1 Hardware Reset
- 11.2 Installer Lock
- 11.3 Keypad Lockout Feature
- 11.4 Battery Charge Current
- 11.5 Partitioning
- 11.6 System Real-Time Clock
- 11.7 Clock Adjust
- 11.8 Keypad Tamper Supervision
- 11.9 Keypad Audible Trouble Warning
- 11.10 Confidential Mode
- 11.11 Installer Quick Functions Keys
- 11.12 PGM Modules Supervision
- 11.13 Printer Module Supervision
- 11.14 Zone Expansion Bus Module Supervision
- 11.15 Wireless Transmitter Low Battery Supervision
- 11.16 Wireless Transmitter Supervision Options
- 11.17 ReProgram All Expansion Modules
- Part 12: Settings for WinLoad Software
- Part 13: User Operation
- 13.1 Trouble Display
- 13.2 Programming Access Codes
- 13.3 Disarming & Deactivating an Alarm
- 13.4 Regular Arming
- 13.5 Stay Arming
- 13.6 Instant Arming
- 13.7 Force Arming (Not to be used with UL Installations)
- 13.8 Manual Bypass Programming
- 13.9 One-Touch Arming
- 13.10 Keyswitch Arming
- 13.11 Panic Alarms
- 13.12 Auto-Arming (Not to be used with UL installations)
- 13.13 Alarm Memory Display
- 13.14 Programming Chime Zones
- 13.15 Keypad Muting (Not to be used with UL installations)
- 13.16 Keypad Backlight (1686H and 1686V only)
- FCC WARNINGS
- Index
9.7 EVENT CALL DIRECTION
This feature determines where each group of events will be reported. The control panel events are divided into five groups (see
above) where each event group can be programmed to dial one or both Central Station Telephone Numbers. When a reportable
event occurs in the system, the control panel will verify that one of the two telephone numbers has been enabled. The control
panel will begin by dialing the selected telephone number(s). If both numbers were selected it will begin with Central Station
Telephone Number 1. After the Maximum Dialing Attempts (see page 35) to one central station telephone number have failed, the
control panel will then dial the backup telephone number. If the Alternate Dial Option (see page 36) is enabled, the control panel
will dial the programmed backup telephone number after every failed attempt. If no backup telephone number is programmed,
the control panel will never report to the backup telephone number. Also, refer to Delay Between Dialing Attempts on page 36.
Example: The system is armed and zone 1 has been breached causing an alarm. If option [3] is off and option [4] is on in section
[137], the control panel will attempt to communicate with Central Station Telephone Number 2 in order to transmit the Zone 1
Alarm Report Code programmed in section [187].
9.8 DIALING METHOD
Section [135]: Dialer Options
Option [4] OFF = Pulse Dialing. (Also, refer to Pulse Ratio, below)
Option [4] ON = Tone/DTMF Dialing (default)
9.9 PULSE RATIO
Section [135]: Dialer Options
Option [5] OFF = European Pulse Ratio of 1:2
Option [5] ON = U.S.A. Pulse Ratio of 1:1.5 (default)
When using Pulse dialing, you can select one of two Pulse Ratios. Although most European countries use the 1:2 pulse ratio, the
1:1.5 ratio may provide better results in some cases. The same applies for North American countries. If the 1:1.5 pulse ratio is not
providing the desired results, the 1:2 ratio may be used.
9.10 BELL ON COMMUNICATION FAILURE
Section [135]: Dialer Options
Option [6] OFF = Bell On Communication Failure Disabled (default)
Option [6] ON = Bell On Communication Failure Enabled
If the control panel fails to communicate with the central station when the system is armed, it will enable the
BELL output, setting
off any bells or sirens connected to the output.
9.11 DIAL TONE DELAY
Section [136]: Dialer Options
Option [5] OFF = Dialer will continue to dial if no dial tone is present after 4 seconds (default).
Option [5] ON = Dialer will hang-up if no dial tone is present after 16 seconds
9.12 MAXIMUM DIALING ATTEMPTS
Section [081]
001 to 016 attempts, Default = 8 attempts
The value programmed in section [081] determines how many times the control panel will re-dial the same Central Station
Telephone Number before proceeding to the next number.
Section [137]
Option [1] ON = Call Telephone #1 for
Option [2] ON = Call Telephone #2 for
Option [3] ON = Call Telephone #1 for
Option [4] ON = Call Telephone #2 for
Option [5] ON = Call Telephone #1 for
Option [6] ON = Call Telephone #2 for
Section [138]
Option [1] ON = Call Telephone #1 for
Option [2] ON = Call Telephone #2 for
Option [3] ON = Call Telephone #1 for
Option [4] ON = Call Telephone #2 for
Arm/Disarm Report Codes in sections [160] to [186] (page 31)
Alarm/Restore Report Codes in sections [187] to [196] (pages 31 to 32)
Tamper/Restore Report Codes in sections [197] to [204] (page 32)
Trouble/Restore Report Codes in sections [205] to [210] (pages 32 to 33)
Special Report Codes in sections [211] to [213] (page 33)