Installation Manual

Smart Lighting Node Hybrid NEMA
MinebeaMitsumi Inc.
3-9-6 Mita, Minato-ku, Tokyo 108-8330 • Phone: [phone] • www.minebeamitsumi.com
Before the installation
Before the installation, the
installer/user must read the full manual
available at the following internet
address upon registration at Paradox
Engineering website:
Warnings (English)
The following instructions provide
important precautions to safely install,
use and maintain the product.
Please read and follow them carefully
before operating the unit: failure to
comply may compromise people safety
and/or damage the device, with serious
consequences depending on
circumstances.
• The equipment is Class II
equipment and fits outdoor
installation. It does not require
(and must not have) a safety
connection to electrical earth.
• The equipment is intended for
installation, service and repair by
trained and skilled personnel only
(no operator access)
• Install the product in accordance
with the instructions provided in
this installation manual
• The manufacturer shall not be held
liable for errors or damages due to
wrong mounting operations
• This equipment is intended to be
used with elevations up to 2000 m
• The product and the various units
comprising the installation must
only be used for the purpose for
which they are intended. Any other
use is considered improper and
dangerous
• Unpack the product and check
possible damages before installing
and operating it
• Electrical work and installation
must be performed in accordance
with relevant local and national
regulations, following the
instructions provided in this
installation manual.
• Before connecting the product,
make sure that product voltage
ratings correspond to the mains
power supply voltage
• Product drivers are default set as
per the configuration sheet
provided with the product. The
product must only be installed in
luminaires with compatible
drivers.
• When plugging the product on the
luminaire socket, ensure that the
North indicator on the cap is
aligned with the North indicator of
the luminaire socket.
• Install the product under a good
GPS coverage.
• Before cleaning or servicing the
product, disconnect it from the
mains power
• Dispose of packaging or product
must be in compliance with
applicable local and national
waste disposal regulation
• Keep this document for future use
and reference
Warnings (Français)
• L'équipement est un équipement
de classe II et convient à une
installation en extérieur. Il ne
nécessite pas (et ne doit pas avoir)
de connexion de sécurité à la terre
électrique
• Ces équipements sont destinés à
l’installation, l’entretien et la
réparation effectués uniquement
par un personnel formé et qualifié
(aucun accès à l’opérateur)
• Installer le produit selon les
instructions fournies dans ce
manuel d’installation
• Le fabricant n’est pas responsable
d’erreurs ou de dommages
attribuables à des opérations de
montage erronées
• Ces équipements sont destinés à
être utilisés jusqu’à 2.000 mètres
d’altitude
• Le produit et les différentes unités
comprenant l’installation doivent
être utilisés seulement pour les
finalités pour lesquelles ils sont
prévus. Toute autre utilisation est
considérée comme inappropriée et
dangereuse
• Déballer le produit et contrôler les
dommages possibles avant de
l’installer et de le faire fonctionner
• L’installation et le travail
électrique doivent être effectués
conformément aux
réglementations nationales et
locales pertinentes en suivant les
instructions fournies dans ce
manuel d’installation.
• Avant de brancher le produit,
s’assurer que la tension nominale
du produit corresponde à la
tension d’alimentation du réseau
électrique
• Les drivers de produits sont définis
par défaut conformément à la
feuille de configuration fournie
avec le produit. Le produit ne doit
être installé que dans des
luminaires avec des drivers
compatibles.
• Lorsque vous branchez le produit
sur la prise du luminaire, assurez-
vous que l'indicateur Nord sur le
capuchon est aligné avec
l'indicateur Nord de la prise du
luminaire.
• Installez le produit sous une bonne
couverture GPS
• Avant de nettoyer ou d’assurer
l’entretien du produit, il faut le
débrancher du réseau électrique
• L’élimination du produit ou de son
emballage doit être conforme aux
réglementations nationales et
locales pertinentes en matière
d’élimination des déchets
• Conserver ce document pour une
utilisation et des besoins futurs
USA
RF exposure information
The NDLM007US (FCC ID:
2AKPQNDLM007) complies with Part 15 of
the FCC rules. Operation is subject to the
following two conditions:
1) This device may not cause harmful
interference, and
2) This device must accept all
interference received, including
interference that may cause
undesired operation
This device should be operated with a
minimum separation distance of 50 cm
between the equipment and a person’s
body.
The calculations were carried out
assuming no co-location or operation in
conjunction with any other antenna or
device which may contain transmitters.
The equipment contains:
NDLM007US-1, FCC ID: N7NWP77B
NDLM007US-2, FCC ID: N7NWP76B
RF exposure guidelines for addressing
co-location
The device should not be co-located
with any other transmitter during the
installation without following the FCC
co-location procedure first (FCC KDB
447498 RF exposure guidelines for
addressing co-location).
US Responsible party
NMB Technologies Corporation, 9730
Independence Ave, Chatsworth, CA 91311,
United States
Changes
Changes or modifications made to this
equipment not expressly approved by
MinebeaMitsumi inc., may void the
user’s authority to operate this
equipment.
Note
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to part
15 of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio or
television reception, which can be
determined by turning the equipment
off and on, the user is encouraged to try
to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving
antenna.
- Increase the separation between the
equipment and receiver.
- Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced
radio/TV technician for help.
This radiocommunication equipment
has the electromagnetic field strength in
compliance with the Safety Standard for
the Use of Radiocommunication
Equipment on Human Health announced
by the National Telecommunications
Commission.