EX350 358 HOME GYM PRODUCT ASSEMBLY R~VI~ION C
358 EX350 ASSEMBLYPARTS LIST SORT AND COUNTALL PARTSBEFOREBEGINNINGASSEMBLY HARDWARE: ITEM NAME/DESCRIPTION 7. 8. q. I0. l& 17. 20. 27. 28. 29. 30. 32. 34. 30. 40. ,.. QTY 1/2X3 IN.HEX HEAD BOLT ............................................................................ : .................4 I.~ X 3 I/4 IN. HEXHEAD BOLT 4. 1/2_X4 IN.HEX HEAD BOLT ........................................................... : ....................:............. I 318 X ! i/2 IN. HEXHEAD BOL T" 1 3/8XI 3,’4IN.
58 EX350 ASSEMBLY PARTS LIST SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSEMBLY WELDMENTS/PARTS: ITEM. NA~IE/DESCRIPTION QTY 2. .~. 4. 5. 6. 7. 8. 9. I0. II. 12. 14. 15. 16, 17. 19. 20. 21. 22. 23. 24. 25. 27. 28. 20. 30. 32. 34. 35. 36. 37. 38. 3t). 40. BEARING HOUSING WLDMT ........................................... (6293701) ............................... 1 LOWROW SWIVELBRACKET WLDMT ......................... (6199401) ........................... :... 1 MAINUPRIGHTBOTTOM SECTION¯WLDMT ...........
358 EX350 ASSE.~B! ,Y INSTRUCTIONS NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE; HEAD OF THE BOLT. " iii!!ii-il BOLT LENGTH BOLT LENGTH RULER: .0 !," t ¯ I .... !.. 1 ~ ! ,I,, l, 5 I , , ! I ,! 6 I.
358 EX350 A:~SEtvlBLY INSTRUCTIONS ,THANK YOU . :." .; " : ~2..-~.-_:. . ."....~ ~---~.. FOR PURCHASING THE ~ PLEASE SAVE THESE ASSEMBLY INSTRUCTIONs FOR YOUR PERSONAL REFERENCE, AND ADDITIONAL SERVICE INFORMATION.,~,~" . ¯ ***IMPORTANT*** ":: THE EX350 MUST BE ASSEMBLEDON A FLair, FUNCTION. LEVEL SURFACE TO ASSURE ITS:’’"~ PARABODY INC. STRONGLY RECOMMENDSTHAT THIS PRODUCT BE ASsEMBI~ED. PERSONS TO AVOID POSSIBLE INJURY.
358 EX350 ASSE~.,IBLY INSTRUCTIONS Attach BACK/SEAT SUPPORT ASSEMBLYto WEIGHT STACK SUPPORT BASE, u~ing one (1) I/2 X 3-1 ’4 IN. HEX HEADBOLTand one (1) I/2 IN. LOCKNUT.(TIGHTEN ONLYUNTIL SNUG) .Attach one (1) 4-1.’20.D. DIA. [~ULLEYwith’l IN. BUSHINGinto FRONT"U" PULLEYBRACKET of the BACK/SEAT SUPPORT,using one (1) 3/8 X 1-3/4 IN. HEXHEADBOLTand one (1) 3/8 LOCKNUT. .. Attach one (I) 4-I;20.D. D1A. PULLEY,with 2 IN. BUSHING,between two fiats on MAINUPRIGHT TOPSECTION.usln,..., one (I) 3/$ X 3 IN.
358 EX350 ASSEMBLY INSTRUCTIONS USING,EXTREME CARE. slide each of the fifteen (15) WEIGHTPLATESdown ow.’r the GUIDE RODS onto the WEIGHT STACK CUSHIONS. (PIN HOLE FACING OUT) 22. Slide HEADWEIGHTPLATE ASSEMBLYdown over STACK. the GUIDE RODS onto the WEIGHT Position the GUJDE RODS under the GUIDE ROD BRACKETofthe MAIN UPRIGHT TOP SECTION,and hold in place using two (2) GUIDERODPINS. (SEE DETAIL 24. Apply the WEIGHTSTACKLABELS to the WEIGHTPLATES¯ (SEE DETAIL A) 25. Insert 26.
358 EX350 ASSEMBLY INSTRUCTIONS LOOSELYassemble one (1) 3 I/20.D. DIA. PULLEYwith I IN. BUSHINGinto PULLEYBRACKET on the LEGCURLARMASSEMBLY. ..... Using one (1) 3/8 X 2 IN. HEXHEADBOLTand one (1) IN. LOCKNUT. 37. Attach two (2) ROLLERPADS to the LEG CURLARMASSEMBLY.using one (I) ROLLER SHAFT. and two (2; STAR LOCK COLLARS. (NOTE: WHENUSING THE LOWPULLEY OFF THE LEG CURL ARM ASSEMBLY, LOCK IN PLACE BY INSERTING L-PIN INTO BUSHING ON THE LEG CURL EXTENSION NECK) 38.
358 EX350 ASSEMBLY INSTRUCTIONS PuII.CABLE up to the PULLEYin the PULLEYHOUSINGabove the WEIGHTSTACKon the MAIN UPRIGHTTOP SECTION. Pull CABLEover and down PULLEYand thru hole in MAIN UPRIGHT TOP SECTION to SELECT CENTER SHAFT on HEAD WEIGHT PLATE. (REMOVE PULLEY FOR EASE OF INSTALLATION) Attach the PRIMARYCABLEto the HEADWEIGHTPLATE ASSEMBLY.b.v threading STUD into .the SELECT CENTER SHAFT and TIGHTEN COMPLETELY. 44. the ¯ To install the SECONDARY CABLE.
358 EX350 ASSEMBLY INSTRUCTIONS 53. SECURELY assemble the BACKPADto MAINUPRIGHTusing two (2) 3/8 X 3 IN. FlEX HEAD BOLTS and two (2) 3:8 IN. LOCK WASHERS.(HIDEM WELTCLIP SHOULDBE FACING DOWN) 54. ¯ To assemble the PEC DECLOOPCABLE,start by LOOSELY attaching each end of the CABLEto CAMSof the LEFT and RIGHT PEC DEC ARMS,using two (2) 5116 X I IN. HEXHEAD BOLTS.four(4) 5 "16 IN. WASHERS. two (2) 5/16 IN. LOCKWASHERS. and two I’.2) 5/16 NUTS.
358 EX350 ASSEMBLY INSTRUCTIONS 61. Assembl~ one ( I ) SPRINGPIN ASSEMBLY to the SPRINGPIN ASSEMIIILY HOUSING located the SEATSUPPORT TUBEusing one (l) KNOB,one (l) PLUNGER. one (1) SPRING,one SPACER.and one (l) COTTER PIN. (SEE DETAIL 62. Insert one ( I ) I i 2 IN. SO. ENDCAP12 GAinto end ofthe SPRINGPIN ASSEMBLY HOUSING fl~e SEAT SUPPORTTUBE. (SEE DETAILH) 63. Insert one( I ) 2 IN.SQ.ENIDCAPintofrontendof theADJI]STABLE SEATSUPPORT. 64.
....
1"7_PLC.5.
PULLEY tSF1,At.KET .--tPF.r. IDErAF, MLEF’r PEr..D’EC" P,ACK DRAWING ParaBody,Inc. DE.TA IL "C." ~{~ RAMSEY.
HQ~3Kr ,.
’.BOLT ¯ /g SPLITL.~,K ¯ WA.
¯ o o oo ROLLER PAD SHAFT
