I Serious 435103 Steel LEG PRESS ADAPTER.
]IMPORTANT NOTES] WELCOME TO THE WORLD OF $~eiOU$ $~l~i!t Please note: * Thank you for purchasing the 435103 Leg Press Adapter Kit. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * Werecommendcleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your Parabody customer service representative at (800) 328-9714.
PARTS LIST KEY 1 2 3 4 5 6 7 8 QTY PART# DESCRIPTION 6747603 FRONT LEG 1 2 3116202 3-1/2" PULLEY 1 3108102 QUICK DISCONNECT LINK 6427101 KEYHOLE CLEVIS 1 CLEVIS PIN 1 3117305 COTTER PIN 3112901 1 1 6732901 TENSION CORD LEGPRESS CABLE 1 6747901 NOTE:The LEGPRESS ATTAClqTMENT (832101) must PARABODY425103 KEY 9 10 11 12 13 14 15 PART# 6535301 3102501 3102802 3102502 3102801 3102933 3102910 DESCRIP’.
FIGURE 2 STEP 2 ¯ If the 445103 SECOND STACK OPTION is not installed, the rear SHROUD opening must be removed. AI?ply pressure to the bottom of the SHROUD where the "V" groove is and carefuly removethe weight stack opening on the SHROUD as shownin FIGURE3.
3/8 X 2"~ BASE FIGURE 3 ’,TEP3 ¯ SECURELY attach one 3-1/2" PULLEY (2) to the BASEusing one 3/8 X 2" BOLT(14), two 3/8" WASHERS (10), and one LOCKNUT (11). See FIGURE ¯ SECURELY attach one 3-1/2" PULLEY (2) to the FRONT LEG (1) using one 3/8 X 2" BOLT(14), two 3/8" WASHERS (10), and one 3/8" LOCK NUT(11). See FIGURE " ¯ Attach the open end of PRESSLINKCABLE (8) to the QUICKDISCONNECT LINK (3).
1/2 ~LEG FIGURE X 3"(~ PRESS 5 STEP 5 ¯ SECURELY attach the LEGPRESSto the FRONTLEG(1) using two 1/2" X 3" BOLTS(15), two 1/2" WASHERS (12), and 1/2" LOCKNUTS(13).
BASE FIGURE 6 STEP 6 ¯ SECURELY attachthe FRONTLEG(1) to 425 BASEusingtwo 1/2 X 3" BOLTS(15), two 1/2" WASHERS (12) and two 1/2" NUTS(13).
FIGURE DETAIL 7 \ / \ / I LEG CABLE LEG PRESS CABLE CABLE CABLE STEP 7 ¯ Run the LEGPRESSCABLE (8) through the correct hole on the d-ring and attach one KEYHOLE CLEVIS(4) to the end of LEG PRESS CABLE(8).
LEG CABLE LEG CABLE ~ CABLE FIGURE 8 CABLE STEP 8 ¯ Attach one TENSIONCORD(7) to the KEYHOLE CLEVIS(4) using one CLEVISPIN (5) and one COTTER PIN (6) as FIGURE8.
FIGURE 9 BOOM LEG PRESS CABLE STEP 9 ¯ CAREFULLY attach the TENSION CORD(7) to the corresponding small shaft on the TOPBOOM using one 1/4" CAPNUT(9) as shown in FIGURE9.
3/8" X 1" BUTTON~"~ HEAD CAP SCREW 3/8",X 1" BUTTON HEAl3 CAP SCREW SPRING PIN ADJUSTMENT FIGURE 10 STEP 10 ¯ SECURELY attach the four previously removed 3/8 X 1" BUTTON HEADCAPSCREWS to the rear S[]?,OUD. See FIGURE 10. ¯ The 832 LEGPRESSis equipped with a spring pin adjustment to accommodate different sized users and allow easy entry and exit from the machine.To use, you must slightly push against the foot plates to take tension off the pin.
