Parabit Systems Inc. MMR2 Installation and Service Manual Release: Version 1.3 October 2019 Parabit Systems, Inc.
NOTICE Copyright © 2019 by Parabit Systems, Inc. All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the written permission of the publisher.
MMR2 Installation and Service Manual Table of Contents Preface Intended Audience ............................................................................................................................................1 Trademark Acknowledgments ..........................................................................................................................1 FCC Compliance Statement (United States) .................................................................................................
Table of Contents This page intentionally left blank.
Preface Intended Audience This manual is for technicians trained to install and service Parabit Systems, Inc. MMR2 card readers. Trademark Acknowledgments ACS-1EUL, ACS Enterprise, AFH Service, AVA, AXSView Service, MMR2, and SkimGard are registered trademarks of Parabit Systems Inc. or its subsidiaries in the United States and/or other countries. Parabit Systems, Inc. and Parabit are trademarks of Parabit Systems Inc. or its subsidiaries in the United States and/or other countries.
Preface How to Use this Guide This guide provides concise, step-by-step instructions for set-up, configuration, and operation of the ACS-1E and ACS-1EUL systems. Conventions Used in this Guide This guide contains the following conventions: Convention Example Screen names, dialog box names, tab names, window names, field names, and menu names appear in bold font. Click the Customer box. File names are italicized. AxsView.Transceiver.Installer.
Preface Navigating this Manual as a PDF This manual includes embedded hyperlinks for quick access to procedures and other sections when viewing the manual as a PDF. Click on any section title or page reference to immediately display that content. Here are some helpful keyboard shortcuts when using the Adobe Reader: • • • To return to your previous location in the manual after following a hyperlink, press Alt+Left Arrow.
Preface This page intentionally left blank.
Chapter 1 MMR2 Card Reader Installation Follow these instructions to begin installing your MMR2 card reader. 1.1 MMR2 Card Reader Installation ............................................................................................. 5 1.2 Electrical Installation ...............................................................................................................8 1.1 MMR2 Card Reader Installation 1.1.
MMR2 Card Reader Installation Note: 6 MMR2 Card Reader Installation Although the diagrams reference SkimGard (IMSR) readers, these diagrams should be used for MMR and MMR-BT installs, as well.
MMR2 Card Reader Installation MMR2 Installation and Service Manual Ver 1 MMR2 Card Reader Installation 7
MMR2 Card Reader Installation Electrical Installation card reader 1.2 Electrical Installation 1.2.1 MMR2 Wiring The wiring for the MMR2, including all of the input and output termination points, is shown in the diagrams on the following pages.
Electrical Installation Note: MMR2 Card Reader Installation The wiring diagram below applies to both the ACS-1E and ACS-1EUL.
MMR2 Card Reader Installation Electrical Installation 1.2.1.2 ACS-1EUL Card Reader and Input Device Wiring The other ends of the sheathed cables and their connection to various ACS-1EUL input devices is shown below.
Electrical Installation MMR2 Card Reader Installation The wiring configuration for the Second card reader board is similar to that of the Controller.
MMR2 Card Reader Installation Electrical Installation ACS-1EUL System with Input & Output Sockets and Terminations 12 MMR2 Installation and Service Manual Ver 1
Chapter 2 Post-Installation Checks and Testing This chapter contains information about the Options Menu. 2.1 Post-Installation Checks ..........................................................................................................13 2.2 Post-Installation Testing ............................................................................................................15 2.3 Troubleshooting ............................................................................................................
Post-Installation Checks and Testing Post-Installation Checks TABLE 2–1. Controller Default Settings Function Description Default Settings Door Sense Jumper (JP1) Near coin-cell battery and Maintenance Mode push-button. Sets the Door Sense to normally-closed (NC) when in place. Jumper in place on Door Sense terminal block and on JP1. Egress (Exit) Switch Input Input opens door (activate door relay) for selected amount of time.
Post-Installation Testing Post-Installation Checks and Testing 2.1.1 Visual Inspection of the MMR2 Card Reader Conduct the following visual inspection of the card reader assembly by referring to the letters in the diagram and corresponding checks below. a b c e d c b a. LED: Check the presence and color of the LED light indicator. • • • Amber Light - Insert Card Green Light - Door Unlocked Red Light - Door Locked b. Screws: Parabit-provided security torque screws must be used.
Post-Installation Checks and Testing Post-Installation Testing 2.2.
Post-Installation Testing Post-Installation Checks and Testing 2.2.2 Additional Test Procedures for the MMR2 Card Reader Field technicians installing the MMR2 system should possess a smartphone with a digital wallet installed containing one active credit card. When planning to perform an MMR2 skim test, a device that operates as an NFC reader is required. Begin by turning on the ACS-1E or ACS-1EUL controller and performing MMR2 System Configuration. (Assistance from an administrator may be required.
Post-Installation Checks and Testing Troubleshooting Complete the following tests to confirm the normal operation of the MMR2 system. 2.3 Troubleshooting Follow the procedure below to troubleshoot common MMR2 card reader issues.
