User Manual
2120
USER MANUAL
PANDORA MINI V4 CAR SERVICESECURITY SYSTEM
Automatic exit from the Service mode
The system can automatically exit the Service mode when a vehicle starts
moving and when an authorization device is in the coverage zone (radio tag,
remote control, mobile device).
NOTE! NO ADDITIONAL SET TINGS ARE REQUIRED FOR THIS FUNCTION. CHECK IF THE
“SPEED” FUNCTION IS SUPPORTED FOR YOUR CAR HERE – LOADER.PANDORAINFO.COM.
CONTROL OVER THE SYSTEM IN CASE OF EMERGENCY
Emergency disarming using the VALET button
In case you cannot disarm the system using a phone or immobilizer tag, the
‘Secret PIN-code’ can be used. The ‘Secret PIN-code’ is written on the Owner’s
personal card under the protective layer. The code must be entered only when
the base unit is powered and the ignition is off. The PIN-code can be entered
using an external or located on the base unit VALET button. The digits input is
indicated by an external or located on the base unit LED indicator.
WARNING! mAke suRe thAt the pRotectIve lAyeR oN the oWNeR’s plAstIc
cARd Is INtAct AfteR AN INstAllAtIoN of the system. the plAstIc cARd holds
the “secRet pIN-code”
WARNING! cARefully Remove the pRotectIve lAyeR, do Not use shARp
objects to AvoId dAmAGING of hIddeN INfoRmAtIoN uNdeR the pRotectIve
lAyeR.
Entering the PIN-code:
• ENTER THE FIRST DIGIT • Press the VALET button the number of times, equals
to the first digit. Pauses between presses should not exceed 1 second. Each
pressing will be confirmed with an orange LED indicator flash. A pause for
more than 1 second and, red LED indicator flash and a short sound signal of the
beeper confirms the input of the first digit. Then you can enter the next digit.
SERVICE (VALET) MODE
It is recommended to put the system into the Service mode before handing
it to a car service or valet parking. When this mode is switched on, security
system stops interfering with built-in electronics and disables all functions to
ease maintenance or parking.
To enable this mode, switch on the ignition, a radio tag must be in the cov-
erage zone, enter the “Immobilizer PIN-code” (if the “Code immobilizer” func-
tion is implemented) and use one of the methods described below: Switch on/
off the service mode using a phone and the Pandora Connect application
• To switch on the Service mode, open the mobile application. When the sys-
tem is active, press and hold the button
on the control panel until the
scale is fully loaded.
• To switch off the Service mode, open the mobile application. When the sys-
tem is active, press and hold the button
on the control panel until the
scale is fully loaded.
NOTE! IN ORDER TO CHANGE BUTTONS LOCATION OR TO ADD A NEW BUT TON ON THE
CONTROL PANEL, PROCEED TO THE “SETTINGS” -> “ACTION BUTTONS”.
Switch on/off the Service mode using a radio tag
• To switch on the Service mode, press and hold the button on a radio tag for
3 seconds. Release the button after 3 flashes of the LED of the radio.
• To switch off the Service mode, press and hold the button on a radio tag for 3
seconds. Release the button after 3 flashes of the LED of the radio tag
.
• Switch on/off the Service mode using an immobilizer button
• To switch on the Service mode, enter the “Immobilizer PIN-code” and press
the immobilizer button 10 times within 20 seconds.
• To switch off the Service mode, turn on the ignition and enter the “Immo-
bilizer PIN-code”.
Service mode indication
The system will confirm switching on the Service mode with:
icon in
the mobile application, with a long sound signal of a Beeper and the green LED
indicator when the ignition is turned on.
The system will confirm switching off the Service mode with: disappearing
the
icon in the mobile application, two long sound signals of a Beeper
and fading the green LED indicator when the ignition is turned on.