User Manual

ManualsBrandsPandora ManualsSecurity SystemPANDORA Mini V4 Car Service Security System

Pandora would like to thank you for choosing our

service-security system

Pandora Mini V4 is a car service-security system, built for cars with on-

board voltage of 12V.

It is a complex engineering product, which includes unique and modern

software and hardware solutions. When building the Pandora Mini V4 we were

using the most up-to-date electronics from world’s best manufacturers. The

device is built using high-precision mounting and control machinery, thus we

guarantee highest possible quality, reliability and stable technical characteris-

tics for the whole operation period.

Elegant and advanced technical design and unique ergonomic interaction

algorithms that are used in the Pandora Mini V4 allow enhancing your car with

fantastic set of intuitive and useful functions.

This device has limited external factors resistance. It should not be subjected to water beyond occasional splatter, or operated in

temperatures outside -40° to +80° C range.

Our web site: www.pandorainfo.com

Customer support: support@pandorainfo.com

WARNING! IT IS STRONGLY ADVISED TO HAVE PROFESSIONAL CAR MECHANIC

INSTALLING THE SYSTEM. ANY CAR ELECTRONICS INSTALLER SHOULD BE ABLE TO

INSTALL THE PANDORA MINI V4 USING INSTALLATION SCHEME IN THIS MANUAL

AND PANDORA SPECIALIST SOFTWARE. MOST FEATURES ARE HIGHLY DEPENDENT ON

COMPETENT INSTALLATION. OUR SYSTEMS ARE THOROUGHLY TESTED FOR QUALITY,

SO IF A FEATURE FAILS TO PRODUCE EXPECTED RESULT, MOST LIKELY THE PROBLEM IS

IN IMPROPER INSTALLATION.

Product is in conformity with Electromagnetic Compatibility

Directive EMC 2004/108/EC and R&TTE Directive 1999/5/EC

Summary of content (25 pages)

PAGE 1
Pandora would like to thank you for choosing our service-security system Pandora Mini V4 is a car service-security system, built for cars with onboard voltage of 12V. It is a complex engineering product, which includes unique and modern software and hardware solutions. When building the Pandora Mini V4 we were using the most up-to-date electronics from world’s best manufacturers.
PAGE 2
Table of contents System set 4 System features Base unit Control and monitoring Arming mode Multi-button code immobilizer Immobilizer mode Anti-Hi-Jack mode Anti-Hi-Jack2 mode 5 5 5 7 7 8 8 9 Immobilizer radio tag Functions of the button Light indication of SEND LED Replacing an immobilizer tag battery Updating firmware of the tag 9 10 10 11 12 Mobile applications Using the application 13 14 Control over the system Arming Disarming 17 17 18 Service (VALET) mode 20 Control over the system in case
PAGE 3
System set SYSTEM FEATURES Base unit Immobilizer tag Blocking relay Cable with VALET button User installation manual Personal owner’s card Beeper (compact sound emitter) Main cable Fastening kit Packaging 1 2 1 1 1 1 1 1 1 1 Base unit • • Integrated 2.4 GHz module with support of Bluetooth 5.
PAGE 4
• Additional sensors Built-in sensors Digital connection Analog connection • • • Arming mode •* •* •* Security zones Interior temperature (status) Engine temperature (status) Outside sensor (status) • Voltage of the on-board circuits (status, security zone – alarm level) • • • Shock sensor (security zone – alarm and warning level) • Motion sensor (security zone – alarm level) Tilt sensor (security zone – alarm level) •* OE alarm system status via CAN, additional sensor, (status, security zo
PAGE 5
• • on the ignition is not required if you want to disarm the system or control time channels. Enter the “Immobilizer PIN-code”. Press a programmed button/lever/pedal the number of times equals to the first digit. Pauses between presses should not exceed 1 second. More than 1 second pause will be interpreted as the start of the next digit input. The immobilizer code can consist max of 4 digits from 1 to 9.
PAGE 6
Light indication of SEND LED • Control button WARNING! It Is • Built-in LED indicator “SEND” Not RecommeNded to plAce the tAG Next to metAl objects, mAGNetIc ANd electRoNIc devIces (mAGNetIc ANd cRedIt cARds, phoNes, keys, key fobs, etc.) foR coRRect op eRAtIoN. do Not expose the tAG to hIGh tempeRAtuRes, moIstuRe. It Is RecommeNded to plAce the tAG oN the belt oR IN the fRoNt pocket of youR clothING • Built-in accelerometer • Battery CR 2032 • 2.
PAGE 7
Updating firmware of the tag • • • Run the mobile app Pandora Specialist. Press and hold the button on the radio tag until the 10th flash of the SEND indicator, then release the button. Select the found device in the app and select one of the update option: INTERNET – firmware will be uploaded by an internet connection. FILE MANAGER – firmware will be uploaded from the phone storage (only for Android).
PAGE 8
IV. EXIT THE PROGRAMMING MODE To finish the pairing procedure, exit the programming mode - switch on the ignition and then switch it off. 20:22 My car 20 oct. 20:22 • Armed SIM The main screen contains the following information and functions: I EVENT HISTORY - provides access to event 12,5V NOTE! IF A MOBILE DEVICE HAS BEEN ALREADY PAIRED, IT WILL BE DELETED WHEN YOU ENTER THIS LEVEL.
PAGE 9
III CONTROL BUTTONS – this panel is used to control a system using buttons. To activate or deactivate a function, press and hold the button until the scale is fully loaded. CONTROL OVER THE SYSTEM Arming To arm the system when the ignition is off, use one of the methods described below. The system will confirm the command receiving with 1 short sound signal and 1 flash of turn indicators.
PAGE 10
VALET button Press and hold the VALET button for 3 seconds. The system will be armed in 30 seconds. The LED indicator is lighting red during the countdown. There is an option in the system settings that allows to arm the system with disabled sensors (shock/tilt/motion and additional sensors). The setting “Switch off sensors when arming using VALET button” is available in the Pandora Specialist. Disarming To disarm the system, use one of the methods described below.
PAGE 11
SERVICE (VALET) MODE Automatic exit from the Service mode It is recommended to put the system into the Service mode before handing it to a car service or valet parking. When this mode is switched on, security system stops interfering with built-in electronics and disables all functions to ease maintenance or parking.
PAGE 12
• ENTER THE SECOND DIGIT • Press the VALET button the number of times, equals to the second digit. Pauses between presses should not exceed 1 second. Each pressing PIN 2-2-2-2 will be confirmed with an orange LED indicator flash. A pause for more than 1 second and, red LED indicator flash and a short sound signal of the beeper confirms the input of the second digit. Then you can enter the next digit. • ENTER THE THIRD DIGIT • Press the VALET button the number of times, equals to the third digit.
PAGE 13
MINI WIRING DIAGRAM External button DXL 0110L v4 Base unit (view from the top side) micro-USB Antenna 2.
PAGE 14
SYSTEM INSTALLATION Wiring description General installation requirements Wire №1 (White) — LED/VALET. This wire connects to the red wire of the external VALET button. • • • • • • • • • • • • Install the base unit only inside car interior. Install securely each system’s component, as conditions of the car standard operation can harm functionality of the alarm system and cause damage to the car original systems, including the elements of safety in motion.
PAGE 15
Wire №11 (Orange-black) CAN1-L — wire of digital bus CAN1-Low. It connects to an appropriate CAN-Low wire of a car. Wire №12 (Yellow-black) 200mA (-) CH5/CAN2-L — wire of digital bus CAN2Low. It connects to an appropriate CAN2-Low wire of a car. This channel can be assigned as an output, it will not work as a digital bus in this case. Wire №13 (Blue-black) 200mA (-) CH7 — Factory setting is “Turn lights”. This wire connects to a hazard flashers button of a car.
PAGE 16
Programming menu NOTE! SEE THE “INFORMATION” SECTION FOR DESCRIPTION OF SIGNALS INDICATING THE NUMBER OF RECORDED CONTROL DEVICES Pandora Specialist The Pandora Specialist allows configuring the main parameters of the system, uploading firmware updates, downloading installation guides, making the “Pandora CLONE” procedure.
PAGE 17
Programming levels table №10.9 – Pairing a GPS-receiver NAV-035 BT Function VALET button №0 – Entering a level Level №1 – Pairing a remote control R-468BT/Watch2 Erase P1 H1P10 №10.11 – Pairing an RF module RFM-470 H1P11 H1• P1 Update H3 H1P9 №10.
PAGE 18
Level №1 – Pairing a control device R-468BT/Watch2 Prepare to pair a Bluetooth device, turn the device on in accordance with its manual. The system will be in the remote controls pairing mode for 1 minute. After a minute or immediately after pairing a Bluetooth remote control, the system will automatically enter the programming level №0.
PAGE 19
Level №10 – Manage Bluetooth devices/Updating Bluetooth modem firmware • This level is used to pair/remove/update additional devices and to update Bluetooth modem of the system. • Open the plastic case of the sensor carefully and insert a battery into the sensor. If pairing was successful, the LED will light red and the siren/beeper will sound a beep. The system will enter the programming level №0.
PAGE 20
Level №11 – Programming the “Immobilizer PIN-code” The level is divided into 3 sublevels (Sublevel 11.1 – Selecting buttons; sublevel 11.2 entering the PIN-code; sublevel 11.3 – confirmation of the PIN-code input). The system will automatically enter the sublevel 11.1 (Selecting buttons) after entering the level 11. The VALET button is used to proceed to the next sublevels and to save the “Immobilizer PIN-code” • №11.
PAGE 21
INFORMATION Meaning of the LED indicator colors Siren sound and turn indicators signals Indicator status Description Short red flashes System is armed Signal Description Fast red flashes Alarm Alarm, PANIC mode Incessant sound and light signals for 30 sec Fast green flashes System is armed (a radio tag is in the coverage zone) Arming 1 sound and 1 light signals Lit red The system is preparing for automatic arming 2 sound and 2 light signals Orange flash Confirms VALET button press ‘Sen
PAGE 22
Addition devices Door sensor DMS-1OO BT Remote control R-468BT • • • • • Integrated 2.4 GHz radio interface (Bluetooth 4.2 Low Energy protocol) Built-in accelerometer 3 control buttons Built-in LED CR 2032 battery Radio tag BT-760/BT-770/BT-780: • • • • • Integrated 2.4 GHz radio interface (Bluetooth 4.
PAGE 23
Telemetry modules Pandora Eye Pro and NAV-X System modules layout Additional devices designed to extend the system function with telemetric and service functions by GSM and the Internet connection: Ask an installer to mark system’s modules on the picture provided. This information can be important for diagnostics in case system malfunctions. • • • GSM, phone calls pandora-on.
PAGE 24
Installation certificate WARRANTY OBLIGATIONS I, the undersigned ______________________________________________ WARNING! We RecommeNd you to Ask AN INstAlleR to fIll out the IN stAllAtIoN ceRtIfIcAte ANd the WARRANty cARd. these documeNts mAy be RequIRed foR coNtActING the customeR suppoRt Manufacturer guarantees correct operation of the service-security system if exploitation, installation, storage and transportation conditions described in this manual were met.
PAGE 25
Acceptance certificate Pandora Mini V4 is in conformity with Electromagnetic Compatibility Directive EMC 2004/108/EC and R&TTE Directive 1999/5/EC.