Daim Ntawv Qhia Tus Neeg Siv

ManualsBrandsPandora ManualsOtherPandora Mini Moto

USER AND INSTALLATION MANUALPANDORA MINI MOTO

Programming table

FUNCTION

VALET BUTTON

0 – Entering a level



P11

•

H5H3

H10

2 – Changing the Service PIN-code

4 – Reset to the factory settings

10.1.1 – Pairing a radio tag BT760 / BT770 / BT780

10.1.2 – Pairing a radio tag BT760 / BT770 / BT780

10.1.3 – Pairing a radio tag BT760 / BT770 / BT780

10.2.1 – Pairing a D030 / D035 / Band / Watch2

10.2.2 – Pairing a D030 / D035 / Band / Watch2

10.2.3 – Pairing a D030 / D035 / Band / Watch2

10.3.1 – Pairing a door sensor DMS-100BT

10.3.2 – Pairing a door sensor DMS-100BT

10.3.3 – Pairing a door sensor DMS-100BT

10.3.4 – Pairing a door sensor DMS-100BT

10.4.1 – Pairing a radio relay BTR-101

10.4.2 – Pairing a radio relay BTR-101

10.6 – Pairing an additional device RHM-03BT / PS-331BT / PS-332BT

10.7 – Pairing an additional device

10.8 – Pairing a telemetry module Pandora Eye Pro / NAV-X

10.9 – Pairing a GPS-receiver NAV-035 BT

11 – Programming and conguring an «Immobiliser PIN-code»

10.11 – Pairing an RF module RFM-470

13 – Emergency deactivating/activating code Immobiliser

function (pin-to-drive)

15 – Emergency deactivating/activating authorization

devices (Immobiliser, Anti-hi-Jack)

50 – Pairing a mobile phone

100 – Exit the programming menu

DeleteLevel

Update

P – press X times H – hold for X sec



– 1 sec pause

•

– without a pause

Level 0 – Entering a level

Enter programming mode, enter the «Service PIN-code» (default value is 1-1-1-1) using an external

VALET button or the VALET button located on the base unit. After entering programming mode, the

system waits for level input – «Level 0 Entering a level». Enter a desired level using the VALET button (see

the programming table) to change settings or parameters:

• To enter a level («Level 1...17»), press (

P) the VALET button the number of times equals to the

desired level number (1...17), pauses between presses should not exceed 1 second. The system

will confirm correct input with red LED flashes and short sound signals of the Siren and proceed

to the desired level.

• For quick access to the higher level, press and hold (

H) the VALET button. The siren will sounds

tone beeps (up to 10). These sounds means the sequence number of a two-digit level number

(the first signal – level 10, the fifth signal – level 50, the tenth signal – level 100). Release the

VALET button immediately after the desired number of signal. To enter an intermediate level (Level

11…18), press the VALET button the number of times equals to the second digit (1…8) of the

desired level number immediately after releasing the button. The system will confirm correct input

with red LED flashes and short sound signals of the Siren and proceed to the desired level.

Level 2 – Changing the Service PIN-code

Prepare a new value of the «Service PIN-code», it should consist of 4 digits (from 1 to 9). Write down or

remember the new PIN-code.

Enter the programming level 2:

• Enter the first digit of the code using the VALET button. Press the button the number of times equals

to the first digit. Pauses between presses should not exceed 1 second, every pressing will confirm

with an orange LED indicator flash. Pause for more than 1 second and a red LED indicator flash with a

sound from the Siren confirm the input of the first digit. Then you can enter the next digit;

• Enter the other numbers in the same manner. The input of the fourth number will be confirmed by

the series of red and green LED indicator flashes and the series of sound signals of the Siren. The

system will wait for PIN-code re-entering;

• Enter all four digits again.

• If you correctly enter the «Service PIN-code» twice, the indicator will produce the series of red and

green flashes and the Siren will produce the series of sounds, the new PIN-code will be recorded, the

system will return to the programming level 0.

• In case of the incorrect code, input the indicator will be lit red and the Siren will sound a long beep,

the system will not change the code and will return to the programming level 0.