Daim Ntawv Qhia Tus Neeg Siv

31
30
USER AND INSTALLATION MANUALPANDORA MINI MOTO
Emergency control of the Code Immobiliser
This section describes two options to deactivate Immobiliser modes:
• Immobiliser and Anti-hi-Jack - use owner authorization devices (tags, remotes, watches, bands) for
engine blocking;
• Code Immobiliser - uses standard vehicle controls (buttons, levers, pedals) to enter the Immobiliser
PIN-code.
OPTION №1 – Emergency deactivation of the Code Immobiliser
To temporarily deactivate the Code Immobiliser (pin-to-drive) function, turn on the ignition when the system
is disarmed and Service mode disabled. Enter the «Secret PIN-code» from the Owner’s personal card using
the VALE T button. The Immobiliser functions will be deactivated by the time the ignition is turned off.
OPTION №2 – Emergency control of the Code Immobiliser mode
This method is used for a permanent deactivation of the Code Immobiliser (pin-to-drive) function.
Deactivation and activation is made by entering the «Secret PIN-code» from the owner’s personal card
using the VALET button while system is disarmed, ignition is off and the Service mode is disabled.
1. Enter the programming mode by entering the «Secret PIN-code» (from the Owner’s personal
card) or the «Service PIN-code» (factory preset is 1-1-1-1). The PIN-code should be entered using the
external or located on the base unit VALET button.
3. o deactivate the function – The LED indicator will be green after entering the programming level.
The system will wait 10 seconds for entering the «Secret PIN-code». If the PIN-code is not entered within 10
seconds or the input is incorrect, the LED will produce the series of red and green flashes and the system
will return to the programming menu. Enter the «Secret PIN-code» that is written on the Owner’s personal
card. The system will confirm deactivating with a long red LED flash and two sound signals of the Siren.
Turn on the ignition and then turn off to exit programming mode. The function will be deactivated.
4. To activate the function – The LED indicator will light red after entering the programming level.
The system will wait for action. Press the VALET button once to activate the function. The system will
confirm enabling with one short sound signal of the Siren and a green LED light. Turn on the ignition
and then turn off to exit programming mode. The function will be activated
2. Code Immobiliser еnter the programming
level №13 - press the VALET button 13 times
(without pauses).
2. Immobiliser / Anti-Hi-Jack – enter the
programming level №15 - press the VALET button
15 times (without pauses).
PROGRAMMING THE SYSTEM
System settings and parameters can be configured using the Pandora Alarm Studio and Pandora
Specialist application. Some functions can be configured only by the programming menu of the system.
It is required to put the system to programming mode to get access to the settings.
Entering/exiting programming mode
You can enter the programming mode only if the base unit is powered form a USB cable or the main
power supply is connected, the ignition is off, the system is disarmed and Service mode is off.
To enter programming mode, enter the «Service PIN-code» (default value is 1-1-1-1) using an
external VALET button or the VALET button located on the base unit.
!
if yOu dON’T havE ThE «sErvicE piN-cOdE», yOu caN ENTEr prOgrammiNg mOdE usiNg ThE «sEcrET piN-cOdE» wriTTEN
ON ThE OwNEr’s card. iT is fOrbiddEN TO damagE ThE prOTEcTivE layEr Of ThE «OwNEr’s pErsONal card» - ThE iNfOrmaTiON
uNdEr ThE prOTEcTivE layEr Of ThE card is iNTENdEd ONly fOr ThE OwNEr Of ThE sysTEm. whEN ThE OwNEr cOmplaiNs abOuT
ThE ErasEd prOTEcTivE layEr, ThE sysTEm is rEiNsTallEd aT ThE ExpENsE Of ThE iNsTallEr.
The system stops to execute commands when it is in programming mode. Therefore, exit
programming mode after changing settings and parameters of the system.
To exit programming mode, use one of the following methods:
• Press and hold the VALET button for more than 10 seconds;
• Turn on and then turn off the ignition when a USB cable is disconnected and the main power supply
of the system is connected;
• Disconnect the power supply (main and USB power supply).
The system will reboot programmatically (all changes will be saved) after exiting programming
mode. All ways to exit programming mode are accompanied by sound signals of the siren and light
signals of the LED indicator. The light signals indicate the number of paired control devices.
!
sEE ThE «chEckiNg ThE NumbEr Of pairEd dEvicEs sEcTiON Of ThE usEr maNual fOr dETailEd dEscripTiON.