Daim Ntawv Qhia Tus Neeg Siv

29
28
USER AND INSTALLATION MANUALPANDORA MINI MOTO
THE SYSTEM CAN BE CONTROLLED FROM A PHONE WITH AN OPTIONAL
PANDORA EYE PRO / NAVX TELEMETRY MODULE
Call the telemetry module phone number and enter the command after the answer. If the call is
made from a number which is not saved in memory, then after the sound signal you will need to
enter the «Guest PIN-code»:
0* – Disarming
998*xxxх – Deactivate authorization devices, where хххх is the «Secret PIN- code» written on
the Owner’s personal card of the telemetry module.
The system has emergency ways to deactivate security and Anti-Hi-Jack functions (using the VALET
button and the «Secret PIN-code») in case of loss or failure of control devices or in case of discharge of a
battery (when you cannot replace it or charge).
• «Secret PIN-code» is located under protective layer on the «Owner’s personal card»;
• VALET button is located on the external VALET button or on the main unit.
CONTROL OVER THE SYSTEM IN CASE OF EMERGENCY
!
bEfOrE usiNg EmErgENcy sysTEm cONTrOl, chEck ThE sysTEm aNd vEhiclE cONTrOl dEvicEs: chEck a baTTEry, TurN ON a
dEvicE iN accOrdaNcE wiTh iTs maNual (if rEquirEd).
i
f all dEvicEs arE wOrkiNg, Try TO makE a primary vEhiclE diagNOsis: chEck ThE vEhiclE OrigiNal cONTrOl
dEvicE
, vEhiclE baTTEry chargE lEvEl, gEarbOx sElEcTOr pOsiTiON, chEck iNfOrmaTiON ON ThE dashbOard.
Х-Х-Х-Х
LOGIN / PASS
PIN Phone number
Secrete
PIN-code
Protective
layer
Owner’s personal card
!
rEmOvE ThE prOTEcTivE layEr carEfully. dO NOT
usE
aNy sharp ObjEcTs TO avOid damagiNg Of hiddEN
iNfOrmaTiON
uNdEr ThE prOTEcTivE layEr.
External VALET button
!
ThE ExTErNal valET buTTON is placEd iN ThE iNTEriOr
(
chEck «sysTEm mOdulEs layOuT»)
READ THE PROCEDURE FOR ENTERING THE PIN-CODE BEFORE USING EMERGENCY FUNCTIONS.
• Enter the first digit • Press the button the number of times equal to the first digit. Pauses between
presses should not exceed 1 second. Each pressing will be confirmed with an orange LED indicator
flash. Pause for more than 1 second, a red LED indicator flash confirm the input of the first digit. Then
you can enter the next digit.
• Enter the second digit • Press the button the number of times equal to the second digit. Pauses
between presses should not exceed 1 second. Each pressing will be confirmed with an orange LED
indicator flash. Pause for more than 1 second, a red LED indicator flash confirm the input of the
second digit. Then you can enter the next digit.
• Enter the third digit • Press the button the number of times equal to the third digit. Pauses between
presses should not exceed 1 second. Each pressing will be confirmed with an orange LED indicator
flash. Pause for more than 1 second, a red LED indicator flash confirm the input of the third digit.
Then you can enter the next digit.
• Enter the fourth digit • Press the button the number of times equal to the fourth digit. Pauses
between presses should not exceed 1 second. Each pressing will be confirmed with an orange
LED indicator flash. The correct input will be confirmed with the series of green and red flashes
of the LED indicator.
Emergency disarming
Not paying attention to the siren signals, make sure that the ignition is off and enter the «Secret PIN-
code» (see the procedure description above). If there are no siren sounds or LED flashes, check the
battery. It is not possible to enter the «Secret PIN-code», if there is no power supply.
• The system will be disarmed in case of correct PIN-code input. It will be confirmed with the series of
green and red flashes of the LED indicator, the series of sound signals of the Beeper, 4 beeps of the
Siren and 4 signals of the light signalization.
• Emergency disarming is equivalent to a normal method of disarming. No additional actions are
required for further operation of the system.
• The system will stay in previous state in case of incorrect input of the PIN-code. It will be indicated
with a long red flash of the LED indicator. New input can be attempted after 5 seconds.