Instruction Manual

Each pressing is conrmed with an
orange ash of the LED. A pause for
more than 1 second and the red LED
conrms the input for the current
memory cell, you can start entering
the next memory cell.
After entering the code, press the
VALET button to enter the next
sublevel.
№11.2 - Confirmation of the
PIN-code input
Conrm the entered PIN-code on this
sublevel. Repeat the procedure
described above and press the VALET
button. The system will compare two
inputs after that.
- If you correctly enter the code twice,
the indicator will produce the series of
red and green ashes and the Beeper
will produce the series of sounds, the
new code will be recorded, the system
will return to the programming level
0.
- In case of the incorrect code input the
indicator will be lit red and the Beeper
will sound a long beep, the system will
not change the code and will return to
the programming level 0.
Level 13/15 – Emergency
deactivating/activating authorization
devices/functions
________________________________
NOTE! See the detailed description in
the “CONTROL OVER THE SYSTEM IN
CASE OF EMERGENCY” section of the
user manual.
To deactivate/activate “Code
immobilizer function” (pin-to-drive),
enter the programming level 13.
To deactivate/activate authorization
devices (mobile phone, radio tags,
Bluetooth remote control), enter the
programming level 15.
• Deactivating the function
The LED indicator will light green after
entering the programming level. The
system will wait (10 seconds) for
entering the ‘Secret PIN-code’. If the
PIN-code is not entered within 10
seconds the system will return to the
programming menu. Enter the ‘Secret
PIN-code’ that is written on the owner’s
card. The system will conrm
deactivating the function with a long
red LED ash, two sound signals of the
siren and sound signals of the beeper.
• Activating the function
The LED indicator will light red and the
PROGRAMMING THE SYSTEM
System settings and parameters can be
congured using the Pandora Alarm
Studio application. Some functions can
be congured only by the
programming menu of the system. It is
required to put the system to
programming mode to get access to
the settings
Entering/Exiting programming
mode
You can enter the programming mode
only if the base unit is powered form a
USB cable or the main power supply is
connected, the ignition is o, the
system is disarmed and service mode is
o. To enter programming mode, enter
the “Service PIN-code” (default value is
1-1-1-1) using an external VALET
button or the VALET button located on
the base unit.
________________________________
NOTE! See the detailed description of
PIN-code entering procedure in the
“CONTROL OVER THE SYSTEM IN CASE
OF EMERGENCY” section of the user
manual.
If you don’t have the ‘Service PIN-code’,
you can enter programming mode
using the ‘Secret PIN-code’ written on
the owner’s card.
The system stops to execute
commands when it is in programming
mode. Therefore, exit programming
mode after changing settings and
parameters of the system.
To exit programming mode, use one of
the following methods:
• Press and hold the VALET button for
more than 10 seconds;
• Turn on and then turn o the ignition
when a USB cable is disconnected and
the main power supply of the system is
connected;
• Disconnect the power supply (main
and USB power supply).
The system will reboot
programmatically (all changes will be
saved) after exiting programming
mode. All ways to exit programming
mode are accompanied by sound
signals of the siren and light signals of
the LED indicator. The light signals
indicate the number of paired control
devices.
_______________________________
NOTE! See the “Checking the number of
recorded remote controls/radio
tags/mobile device” section of the user
manual for detailed description
________________________________
NOTE! The description of pairing is
printed on the side of this manual
where the wiring diagram is shown.
Level 2 – Changing the Service
PIN-code
________________________________
NOTE! Prepare a new value of the
“Service PIN-code, it should consist of 4
digits (from 1 to 9). Write down or
remember the new PIN-code
Enter the programming level 2.
• Enter the rst digit of the code using
the VALET button. Press the button the
number of times equals to the rst
digit. Pauses between presses should
not exceed 1 second, every pressing
will conrm with an orange LED
indicator ash. Pause for more than 1
second and a red LED indicator ash
with a sound from the Beeper conrms
the input of the rst digit. Then you can
enter the next digit;
• Enter the other numbers in the same
manner. The input of the fourth
number will be conrmed by the series
of red and green LED indicator ashes
and the series of sound signals of the
Beeper. The system will wait for
PIN-code re-entering;
• Enter all four digits again.
- If you correctly enter the “Service
PIN-code” twice, the indicator will
produce the series of red and green
ashes and the Beeper will produce the
series of sounds, the new PIN-code will
be recorded, the system will return to
the programming level 0.
- In case of the incorrect code input the
indicator will be lit red and the Beeper
will sound a long beep, the system will
not change the code and will return to
the programming level 0.
Level 3 – Recording the idle speed
(rpm)
________________________________
NOTE! To timely turn o the starter
during automatic or remote engine
start and the correct operation of the
«Smart Turbo Timer», it is necessary to
record the engine idle speed via digital
or analog tachometer input.
Enter the programming level 3.
• Turn on the ignition and start the
engine. Wait until the stable idle speed
will be reached (the engine should be
warmed-up, idle speed should match
the stable idle speed of the warmed-up
engine). The system will conrm the
presence of the idle speed status with
green ashes of LED indicator.
• Press the VALET button once to save
idle speed. Successful recording of the
idle speed will be conrmed with the
Level 0 Entering a level
After entering programming mode, the
system waits for level input – “Level 0
Entering a level”. Enter a desired level
using the VALET button (see the
programming table) to change settings
or parameters.
• To enter a level (“Level 1…17”),
press (P) the VALET button the number
of times equals to the desired level
number (1…17), pauses between
presses should not exceed 1 second.
The system will conrm correct input
with red LED ashes and short sound
signals of the siren/beeper and
proceed to the desired level.
To enter a sublevel or a cell of sublevel
make a pause for more than 1 second

, then press (
P) the VALET button the
number of times equals to the desired
sublevel or cell number: “Level 10

(1sec.) “Sublevel 1…10”

(1sec.) “Cell
of sublevel 1…4”.
• For quick access to the higher level,
press and hold (H) the VALET button.
The siren will sounds tone beeps (up
to 10). These sounds means the
sequence number of a two-digit level
number (the rst signal – level 10,
the fth signal – level 50, the tenth
signal – level 100). Release the VALET
button immediately after the desired
number of signal. To enter an
intermediate level (Level 11…17),
press the VALET button the number of
times equals to the second digit (1…7)
of the desired level number
immediately (•) after releasing the
button. The system will conrm correct
input with red LED ashes and short
sound signals of the siren/beeper and
proceed to the desired level.
Level 1 – Pairing a remote
control/Watch2
Prepare to pair a Bluetooth device
(remote control or Watch2) in
accordance with its manual. The system
will be in the remote controls pairing
mode for 1 minute. After a minute or
immediately after pairing a Bluetooth
remote control, the system will
automatically enter the programming
level 0.
868 MHz remote controls are paired
one by one, all 868 MHz remote
controls that was previously paired will
be removed.
A Bluetooth remote control must be
paired last or separately. To remove a
Bluetooth remote control, press and
hold the VALET button for 3 seconds on
the programming level 1.
manual where the wiring diagram is
shown.
• Updating firmware of the built-in
Bluetooth modem/Updating firmware
of an additional device
Enter an appropriate sublevel or a cell
of the PROGRAMMING TABLE and use
the Pandora BT application to update
rmware.
To update rmware of the built-in
Bluetooth modem, enter the “Level 
10’”

“Sublevel 10”. To update
rmware of an additional device, enter
the “Level 10”

“Sublevel” or “Cell”
corresponding to an additional device.
The LED will light red after entering.
Press and hold (H) the VALET button
for 6 seconds. Open the Pandora
Specialist, go to “Search device” screen
and select the device and then select
one of the update option:
INTERNET – It allows you to upload
rmware from a server.
FILE MANAGER – This function is
available only for Android devices. It
allows you to upload rmware from
phone storage.
Level 11 – Programming and
conguring an “Immobilizer
PIN-code”
The level is divided into 3 sublevels
(Sublevel 11.0 – Selecting buttons;
sublevel 11.1 entering the PIN-code;
sublevel 11.2 – conrmation of the
PIN-code input). Use the VALET button
to navigate between sublevels and
save the code.
Enter the programming level  11
Sublevel 11.0 – Selecting buttons:
The system will automatically enter the
sublevel 11.0 (Selecting buttons) after
entering the level 11. The system will
wait for buttons pressing. Each
pressing will be conrmed with an
orange ash of the LED. You can turn
on the ignition (the system will stay in
programming mode). Some buttons
can be detected via digital bus only
when ignition is on. The system can
determine buttons via analog “Code
immobilizer 1” and “Code immobilizer
2” inputs or via digital protocol of a car.
After selecting active buttons, press the
VALET button to enter the sublevel 11.1
(Entering the PIN-code).
Sublevel 11.1 – Entering the
PIN-code:
Program the immobilizer deactivation
PIN-code using the selected button or
buttons on this sublevel. The code can
consist of one or more memory cells,
each memory cell can store a sequence
of pressing each of the ve selected
immobilizer buttons.
The code is entered by pressing the
selected buttons for at least 1 second.
PANDORA ALARM STUDIO
The Pandora Alarm Studio application
allows you to change the main settings
and parameters of the system, update
rmware, download installation
manuals, connect to the server to make
CLONE procedure.
Working with the Pandora Alarm
Studio
________________________________
A current version of the Pandora
AlarmStudio can be downloaded from
pandorainfo.com. The Pandora
AlarmStudio is provided only to
authorized installers of Pandora
systems.
Download the Pandora AlarmStudio to
a PC with Windows XP/Vista/7/8/10.
• Run the Pandora AlarmStudio;
• Connect the system to the PC via a
USB cable;
• Put the system to the programming
mode;
• The Pandora AlarmStudio will
automatically connect to the system
and you will be able to congure
settings and update rmware.
It is recommended to update rmware
of the base unit before installing and
programming the system:
• Open the “Update Software” window
and select one of the update options
(“Load from le” – upload rmware le
from a PC folder, “Firmware archive” –
upload rmware from a server to
“rmwares” folder);
• Select rmware and press the
“Update” button to upload rmware to
the base unit.
It is required to exit programming
mode after settings were changed or
rmware was updated.
________________________________
NOTE! If boot mode has been
interrupted for some reason and the
status indicator lights red, you need to
load rmware using quick boot mode
(without entering the PIN-code). Open
AlarmStudio, de-energize and
disconnect the system, press and hold
VALET button located on the base unit,
release the button immediately after
connecting the system and a computer
via USB cable, the system will enter
boot mode.
PROGRAMMING TABLE
________________________________
NOTE! The programming table is printed
on the side of this manual where the
wiring diagram is shown
series of red and green ashes of the
LED indicator and the series of sound
signals of the Beeper. The system will
exit programming menu and reboot
after saving the idle speed.
Level 4 – Reset to the factory
settings
________________________________
NOTE! The procedure recovers the
factory settings of the system without
deleting previously registered devices
(tags, mobile device, relays, etc.) that is
stored in the non-volatile memory.
Enter the programming level 4.
• Press and hold the VALET button for
more than 4 seconds. Release the
button after a sound of the
Siren/Beeper. The system will conrm
the resetting to the factory settings
with a long red ash of the LED
indicator. After that, the system will
reset the settings to default and return
to the programming level 0.
Level 10 – Manage Bluetooth
devices
Updating Bluetooth modem rmware
________________________________
ATENTION! All functions of this level
are available in the Pandora Specialist
app.
This level is used to pair/remove/
update additional devices and to
update Bluetooth modem of the
system.
Each device is paired at a sublevel. To
pair devices of the same type, a
sublevel is divided into cells. To enter a
sublevel or a cell of sublevel make a
pause for more than 1 second (

),
then press (P) the VALET button the
number of times equals to the desired
sublevel or cell number: “Level 10

(1sec) “Sublevel 1…10”

(1sec) “Cell
of sublevel 1…4”.
• Pairing/Deleting an additional
device
Each sublevel or cell displays its
current state by a color of the LED:
green light means the system is ready
for pairing, red light means a device
has been already paired and it is
required to delete it for pairing a new
device. To delete a device, press and
hold the VALET button for 3 seconds (3
orange ashes of the LED). The system
will be in pairing mode for 1 minute.
After a minute or immediately after
pairing a device, the system will
automatically enter the programming
level 0.
________________________________
NOTE! Examples of pairing Bluetooth
devices are printed on the side of this
v 1.0
1
2 3
4 5 6
7 8
beeper will emit a long sound signal
after entering the programming level.
The system will wait for an action. Press
the VALET button once to activate the
function. The system will conrm
activating with a green LED ash and
one short sound signal of the siren and
beeper.
Level 17 – Programming bypass of
an original immobilizer
Bypass learning procedure is
performed on this level.
________________________________
NOTE! See the detailed instruction in
the installation manuals for cars.
Level 50 – Pairing a mobile phone
________________________________
NOTE! See the detailed description in
the “MOBILE APPLICATIONS” section of
the user manual.
The system supports only one mobile
device. If a mobile device has been
already paired, it will be deleted when
you enter this level. When you
overwrite the same device in the
system memory, you should delete the
Bluetooth connection on your mobile
device, delete the mobile device from
the system memory and then pair the
mobile device with the system again.
Put the system in programming mode
by entering the “Service PIN-code”
(default value is 1-1-1-1). The system
will enter the programming level 0.
Press and hold the VALET button for 5
seconds (until the fth sound signal of
the beeper or the fth orange ash of
the LED) to enter the programming
level 50.
The LED indicator will light green after
entering the programming level 50
and the system will enter the mobile
device pairing mode. Turn on
Bluetooth on your mobile phone and
open the mobile application. Go to the
search device screen and select the
found system. The system will conrm
the pairing with the series of green and
red ashes of the LED and a sound
signal of the siren. The system will
return to the programming level 0.
________________________________
ATTENTION! If there is no automatic
pairing, enable the “PIN request for
phone pairing” item in the “Radio tag
and mobile device functions” settings
in the Pandora Alarm Studio
application and make the pairing
procedure again. A mobile device will
request a PIN-code (Factory pre-set is
FUEL LEVEL CALIBRATION
_______________________________________
WARNING! This procedure is used only in case of
analog connection. At least 2 values are required
for correct display of fuel level.
Make a connection in of the «Fuel level input» to
an original fuel sensor Enable the “Use INP (+) to
control fuel level” setting in the Alarm Studio.
Set the value:
• Start the engine
• Call the system number and wait for the answer
• Dial 424* command (Fuel level calibration). The
system will conrm the input of the command.
• Dial a DTMF command (use values from the table
below, it depends on the current fuel level). The
system will conrm the input of the command
(xxx* - command executed).
• End the call.
FUEL LEVEL CALIBRATION TABLE (424*)
DTMF command Fuel level
0* 0%
10* 10%
20* 20%
25* 25%
30* 30%
40* 40%
50* 50%
60* 60%
70* 70%
80* 80%
90* 90%
100* 100%
88 * Reset all calibration values
0-0-1-1-1-1 where the 4 last digits
1-1-1-1 are the “Service PIN-code”, it
will be dierent if you have changed
the “Service PIN-code”).
Level 100 – Exit the programming
menu
________________________________
NOTE! See the detailed description in
the “MOBILE APPLICATIONS” section of
the user manual.
To exit the programming menu, press
and hold the VALET button for more
than 10 seconds until the tenth sound
signal of the Siren/Beeper or until a red
ash of the LED. The system will exit
programming mode and will reboot
programmatically.