Instruction Manual

ManualsBrandsPandora ManualsCar alarmPandora Elite V2 Car Alarm

Pairing a Watch2

(not included with the system)

• Enter the programing level №1.

• If the LED is green, the system is ready for pairing*.

• Go to the MENU -> Settings -> Bluetooth -> Car -> Pair in the Watch2 menu and

wait for pairing.

• If pairing was successful, the LED will be red, the siren/beeper will sound a beep.

The system will enter the programming level №0.

№1

Pairing a remote control D030

(not included with the system)

№1

• Enter the programing level №1.

• If the LED is green, the system is ready for

pairing*.

• Press and hold 3 buttons of a remote

control (arm/disarm/F) simultaneously

for 1 second (until a short beep), then

release the buttons.

• If pairing was successful, the LED will

be red, the siren/beeper will sound a

beep. The system will enter the

programming level №0.

Function

VALET button

0 – Entering a level



P10

•

H3*

H10

1 – Pairing a remote control D030/Watch2

2 – Changing the Service PIN-code

3 – Recording the idle speed (rpm)

4 – Reset to the factory settings

10.1.1 – Pairing a radio tag BT760/BT770

10.1.2 – Pairing a radio tag BT760/BT770

10.3.1 – Pairing a door sensor DMS-100 BT

10.3.2 – Pairing a door sensor DMS-100 BT

10.3.3 – Pairing a door sensor DMS-100 BT

10.3.4 – Pairing a door sensor DMS-100 BT

10.4.1 – Pairing a radio relay BTR-101

10.4.2 – Pairing a radio relay BTR-101

10.5 – Pairing a mobile phone

10.6 – Pairing an engine compartment

module RHM-03BT/PS-331BT/PS-332BT

10.7 – Pairing an additional device DI-04 or BT-01

10.8 – Pairing a telemetry module Pandora Eye Pro

10.9 – Pairing a GPS-receiver NAV-035 BT

10.10 – Updating Bluetooth modem rmware



P1110.11 – Pairing an RF module RFM-470

11 – Programming and conguring an “Immobilizer PIN-code”

13 – Emergency deactivating/activating code immobilizer

function (pin-to-drive)

15 – Emergency deactivating/activating authorization

devices (immobilizer, anti-hi-jack)

17 – Programming bypass of an original immobilizer

50 – Pairing a mobile phone

100 – Exit the programming menu

LevelLevel Update

P – press X times H – hold for X sec.



– 1 sec. pause

•

– without a pause

Control by the VALET button (see the “Level 0 Entering a level” section

Pairing a radio relay BTR-101

• Connect the wire 1 (GROUND) to a grounded spot of a car.

• Enter the programing level №10.4.1 or №10.4.2.

• If the LED is green, the system is ready for pairing*.

• Connect the wire 3 (PROGRAMMING) to wire 4 (+12V POWER

SUPPLY). Connect them to +12V.

• If pairing was successful, the LED will light red and the

siren/beeper will sound a beep. The system will enter the

programming level №0.

• Disconnect the wire 3 (PROGRAMMING) from the wire 4 and

insulate all unused wires. Connect the wire 4 to the ignition

(+12V when ignition is on).

NC - Blocking relay

NO - Blocking relay

PROGRAMMING

+12V POWER SUPPLY

GROUND 

M - Blocking relay

2.4 GHz Antenna

nom 10A

max 20A

}

Connect for programming

№10.4

№10.1.1 - 3

Pairing radio tags BT760/BT770

• Enter the programing level №10.1.1…3.

• If the LED is green, the system is ready for

pairing*.

• Press the control button on a tag and

hold it for 6 seconds (6 ﬂashes of the tag

status indicator), release the button after

the sixth ﬂash.

• If pairing was successful, the LED will

light red and the siren/beeper will sound

a beep. The system will enter the

programming level №0.

SEND indicator

Control button

WIRING DIAGRAM

model: Pandora Elite v2

WARNING! Before starting the installation of the system, choose a

car model in the ALARM STUDIO (CAN-bus protocol).

WARNING! Do not shield the built-in antennas when installing the

system and additional devices. Keep minimum distance of 2 mm

between the modules and metal parts.

WARNING! Disconnect the power supply before

installing/replacing a SIM-card

WARNING! All power circuits of additional devices that are not

powered through the base unit of the system should have their

own fuses.

IT IS FORBIDEN to install the system on a car with normal voltage

other than 12V.

IT IS FORBIDEN to bypass original fuses of a security system in the

installation process.

IT IS FORBIDEN to install the security system with damaged output

cables.

1 2 3

XP6

XP5

XP3

External VALET button

LED indicator

VALET button

XР2

White

Black

Green

IMMO-KEY2 OUT

IMMO-KEY1 IN

IMMO-KEY1 OUT

WARNING! XP3 connector (IMMO-KEY) is used for remote

engine start only (see installation manuals on

loader.pandorainfo.com or in the Alarm Studio).

POWER (+12V)

CH14

–

Starter

CH11

–

Bypass

CH9

–

Blocking NO

CH2

–

Ignition

CH5

–



XP7

Relay module RMD-5M

** Total current of the relays R3+R4+R5

cannot be more than 40A

* If the 2.2.1 setting “Car with START/STOP

button” is enabled, then Ignition is - START/STOP,

ACC is Brake pedal).

40

R1 R2 R3 R4 R5

20A

**20A**20A**20A20A

Brown

Yellow

Orange

Green/Red

Blue/Red

Blue

Blue/Black

Green

Green/Black

Red

Relay module

Red

Brown

Yellow

Orange

Green

Blue

(–)

(+)

+12B

200mA

200mA (-)

(+)

(-)

CAN2-L

CAN2-H

CAN1-L

CAN1-H

CH8 – Output “Locking Central Lock”

INP9 – Input “Ignition”

INP5 – Input “Hood”

200mA (-)

6 – Output “Unlocking Central Lock”

CH10 – Output “NO Blocking”

Green/Black

Yellow

Yellow/White

Orange/White

Green/Blue

Orange/Black

Yellow/Black

Brown/White

Blue/Black

Blue

CH12 – Output “Turn signals”

micro-USB

nano-SIM

XP1

XP4

XP3

XP2

XP5

XP7

XP6

XP8

XP9

Temperature sensor

(engine/

interior/

outside temperature)

VALET

button

2A(+)

CH17

–

Output “Turn signals”

CH19

–

Output “Video Recorder”

GROUND (-)

12В, max=4Ач

BACKUP POWER SUPPLY

(Warning! Do not connect to the main power supply of the system)

XP8

CH18 - Output “Siren” (+12V)

Gray/red

Gray/Black

Black

Gray

Purple

Red

POWER SUPPLY +12V

GSM/3G/LTE Antenna

(Connection of the antenna is mandatory)

2.4GHz (BT5.0)

Antenna

GPS/GLONASS

Antenna

LED

CAN/LIN

GSM

IT IS FORBIDEN to install the temperature sensor at the place

where temperature is higher than the operating range of the

sensor (+125C) and cable (+80C).

13

15

200mA (-)

(-)

16 – Output “Switching o ACC”

(door opening simulation after engine is stopped)

200mA (-)

INP7/CH3 – Output “Ignition”

CH1/INP4 – Input “Doors”

CH7/INP6 – Input “Trunk”

200mA (-)

INP3/CH4 – Output “Beeper”

INP8 - Input “Neutral”

(Mechanical/

Automatic/Robotic transmission)

INP2 - Input “Brake pedal”

INP1– Input ”Fuel level”

Input “Tachometer”

LIN1 IN – Break of the digital bus

(statuses/control of a vehicle)

LIN2 – Digital bus “Engine Pre-heater”

(control of Webasto/Eberspacher)

LIN1 OUT – Digital bus

(statuses/control of a vehicle)

200mA (-)

(+)

Green/Orange

Orange/Black

White/Blue

White/Green

Yellow/Brown

Brown

Pink

Black

White/Gray

White

Brown/Black

Red/Black

Green

White/Yellow

White/Black

CAN3-L

CAN3-H

Gray/Black

LIN1 OUT

+12V

amp

3..100В, min 8Gz)

Pairing remote control D-043 with the RF module RFM-470

• Enter the programing menu of the system (level №0).

• Brieﬂy press the CALL button on the RF module.

• If the LED is green and the Siren/beeper sounded a beep, the

system is ready for pairing*.

• Press and hold 3 buttons of a remote control (arm/disarm/F)

simultaneously for 1 second (until a short beep), then release

the buttons.

• If pairing was successful, the siren/beeper will sound a beep.

• Pair the next remote controls (up to 4) consequentially.

• Press the CALL button on the RF module to ﬁnish pairing.

• The system will conﬁrm ﬁnishing with the series of red and

green ﬂashes of the LED. The system will enter the

programming level №0.

Pairing an RF module RFM-470

№10.11

• Connect the wire 2 (Black) to a grounded spot of a car.

Connect the wire 3 (Red) to constant +12V.

• Enter the programing level №10.11.

• If the LED is green, the system is ready for pairing*.

• Press and hold the CALL button on the RF module until the

sixth beep of the BEEPER-RFM (sixth ﬂash of the BEEPER-LED).

• If pairing was successful, the LED will light red and the

siren/beeper will sound a beep. The system will enter the

programming level №0.

Red

Black

+12V POWER SUPPLY)

GROUND (-)

2.4 GHz (BLE4.2)

Antenna

Sound indicator

BEEPER RFM

Light indicator

of armed mode

(ashes on/o/

rst 3 minutes)

868 MHz

Antenna

CALL

button

LED RFM

indicator

PROGRAMMING TABLE

Pairing door sensor DMS-100 BT

(not included with the system)

• Enter the programing level №10.3.1…4.

• If the LED is green, the system is ready for pairing*.

• Open the plastic case

①

of the sensor carefully and insert

a battery

②

into the sensor.

• If pairing was successful, the LED will light red and еру

siren/beeper will sound a beep. The system will enter the

programming level №0.

2.4GHz

Antenna

№10.3

2.4GHz Antenna

+12V POWER SUPPLY

GROUND 

IN RHM/PS – Input “Trunk”

CH BLE PS – Output

PROGRAMMING

Connect for

programming

(+/-)

(-) 200mA

RHM/PS

Temperature sensor

(engine/

interior/outside temperature)

Red/Black

Black

Yellow

Green

Pairing a siren PS-331BT

№10.6

• Connect the wire 4 (Green) to wire 2 Black). Connect them

to a grounded spot of a car.

• Enter the programing level №10.6.

• If the LED is green, the system is ready for pairing*.

• Connect the wire 1 (Red) to constant +12V.

• If pairing was successful, the LED will light red and the

siren/beeper will sound a beep. The system will enter the

programming level №0.

• Disconnect the wire 4 (Green) from the wire 4 and insulate

all unused wires.

Control buttons

SEND

indicator

WARNING!

All additional devices included in the system set are paired with the

system. The maximum number of paired Bluetooth devices must not exceed 14.

WARNING!

Do not shield the built-in antennas when installing the additional

devices. Keep minimum distance of 2 mm between the modules and metal parts

*WARNING!

See the “Level 10 – Manage Bluetooth devices” section

Control buttons

Summary of content (2 pages)

PAGE 1
WARNING! Before starting the installation of the system, choose a car model in the ALARM STUDIO (CAN-bus protocol). WARNING! Do not shield the built-in antennas when installing the system and additional devices. Keep minimum distance of 2 mm between the modules and metal parts. WARNING! Disconnect the power supply before installing/replacing a SIM-card WARNING! All power circuits of additional devices that are not powered through the base unit of the system should have their own fuses.
PAGE 2
PROGRAMMING THE SYSTEM The system stops to execute commands when it is in programming mode. Therefore, exit programming mode after changing settings and parameters of the system. To exit programming mode, use one of the following methods: • Press and hold the VALET button for more than 10 seconds; • Turn on and then turn oﬀ the ignition when a USB cable is disconnected and the main power supply of the system is connected; • Disconnect the power supply (main and USB power supply).