ENGLISH DEUTSCH ESPAÑOL WV-CS650 WV-CS654 WV-CSR650 FRANÇAIS Combination Camera Before attempting to connect or operate this product, please read these instructions completely
ENGLISH VERSION We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standards or other normative documents following the provisions of Directives EEC/73/23 and EEC/89/336. Vi erklærer os eneansvarlige for, at dette produkt, som denne deklaration omhandler, er i overensstemmelse med den følgende standarder eller andre normative dokumenter i følge bestemmelserne i direktivene 73/23/EEC og 89/336/EEC.
■ Self Return Setting .................................. 17 ■ Auto Mode Setting .................................. 18 ■ FLIP-A-CHIP Setting ............................... 19 ■ LOCAL/REMOTE Setting ........................ 19 ■ Camera Setting ....................................... 20 INSTALLATION ............................................... 31 CONNECTIONS .............................................. 34 SYSTEM CONNECTIONS ............................... 36 PREVENTION OF BLOOMING AND SMEAR .............
PRECAUTIONS 8. If “OVER HEAT” sign appears on the monitor screen The temperature inside the camera exceeds the normal level because of a malfunction of the cooling fan etc. Turn the power off immediately and refer servicing to qualified service personal. 1. Do not attempt to disassemble the camera. To prevent electric shock, do not remove screws or covers. There are no user serviceable parts inside. Ask a qualified service person for servicing. 2. Handle the camera with care. Do not abuse the camera.
CONSTRUCTION e e* r t w y q u i o (1) Data Cable (only for WV-CSR650) (6) Fall Prevention Wire (2) Video Output Connector (7) Decoration Cover (3) Power Cable for WV-CS650 and WVCSR650 (8) Cooling Holes (9) Dome Cover (3*) Power Cable for WV-CS654 (4) Camera Mounting Angle (5) Panning Start Point -3-
SETUP ■ Setup Menu This camera utilizes a user setup menu that is displayed on-screen. This setup menu contains various sub menus that form a tree-type structure as shown below. This menu is described in the "SETUP MENU DESCRIPTION". Preset Menu MAP Menu Home Position Setting Setup Menu CAMERA SET UP MENU Self Return Setting Auto Mode Setting Position No.
Note: The menus described in bold are displayed only when WV-CSR650 is used. UNIT NUMBER TRANSMISSION SPEED Local/ Remote Shutter Speed ON/OFF Manual Iris Adjustment DATA BIT PARITY BIT STOP BIT XON/ XOFF WAIT TIME ALARM DATA DELAY TIME Camera Menu AGC ON/OFF INT Manual Selection Manual Manual Level Mask Area Adjustment Selection (Contrast) Sensitivity Up ON/OFF LL Manual Selection White Balance AWC ATW Sync.
■ Setup Menu Description ● RS485 site communication (only WV-CSR650) Communication parameters • Full/Half duplex (page 31) • Transmission speed (2 400 - 19 200 bps) (page 11) • Parity bit, Stop bit, Flow control (page 11) • Retransmit time, Delay time, Alarm output (pages 11, 12) • Camera units (96 units max.) (page 31) • Termination ON/OFF (page 31) • Reset parameters (page 31) ● PRESET (1) Position (POSITION SET) POSITION SET adjusts the camera picture by panning, tilting, zooming and focusing.
● AUTO MODE AUTO MODE is for setting the movement of the camera. You can select from three automatic operation modes and one manual operation mode as follows: OFF mode: No automatic operation. The camera can be operated only manually. SEQ mode: The camera operates in the sequence of preset positions in numerical order. SORT mode: The camera operates in the sequence of preset positions counterclockwise from Pan/Tilt Starting Point.
Generally, when a light from the background is too strong such as a spotlight, all objects except the main object in the picture are displayed darker because the lens iris is adjusted with respect to strong brightness. This model ignores strong brightness by masking the source of the strong brightness, thereby all objects are displayed clearly. Note: The result of field setup of the mask area and level adjustment is fed back (effected) to the lens iris control in ALC mode.
(7) White Balance (WHITE BAL) You can select one of two modes for white balance adjustment as follows: • ATW (Auto Tracing White Balance) In this mode, the colour temperature is monitored continuously and thereby white balance is set automatically. The colour temperature range for the proper white balance is approximately 2 600 6 000K. Proper white balance may not be obtained under the following conditions: 1. The colour temperature is out of the 2 600 - 6 000K range. 2.
SETTING PROCEDURES The following setting procedures are described on the assumption that this model is used in combination with the WJ-SX550A matrix switcher and WV-CU550A system controller. If used with the WV-RM70 camera controller, refer to “WV-RM70” on page 5 for operation. ■ Menu Display D4 menu ● Setup Menu Display 1. Select the number of the camera you want to set up and a monitor to display the SET UP MENU. 2. Display the D4 menu on the LCD by pressing the appropriate cursor buttons.
● Changing the camera communication parameters 1. Display the SET UP MENU. Move the cursor to COM. SET UP DISABLE and press the CAM (SET) key to select COM. SET UP ENABLE. 2. Move the cursor to the item and select the parameter by moving the joystick to the left or right. You can remote control this camera by using a specified extension unit such as a computer with a modem. The RS485 menu is used to set the parameters of the below items for RS485 site communication.
Note: When POLLING is selected, the alarm data is not transmitted automatically by using WVCU550A. DELAY TIME Specifies the time to transmit the acknowledge request when communicating on a two-line connection. (OFF, 10, 20, 40, 100 ms) The factory setting is OFF. This menu appears only when a two-line communication is used. The settings become effective with closing of the SET UP MENU.
● Position Setting Preset setting menu 1. Move the cursor to POSITION SET and press the CAM (SET) key. The position set menu is displayed. PRESET NO.15*H POSITION SET PRESET ID ALC/MANUAL DWELL TIME SCENE FILE RET 2. To set panning/tilting positions Move the cursor to PUSH SET next to PAN/TILT and press the CAM (SET) key. The setting menu appears. Select panning/tilting positions moving the joystick up and down, right and left, and press the CAM (SET) key.
● Preset ID Setting Preset setting menu 1. Move the cursor to PRESET ID and move the joystick to the left or right to select ON or OFF. ON: Preset ID is displayed on the screen. OFF: Preset ID is not displayed. PRESET NO.15*H POSITION SET PRESET ID ALC/MANUAL DWELL TIME SCENE FILE RET ON ALC 2S 1 DEL 2. To edit the camera identification to be changed Move the cursor to PRESET ID and press the CAM (SET) key to display the set menu.
To delete an edited PRESET ID Move the cursor to RESET and press the CAM (SET) key. PRESET NO.15*H 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ ().,'":;&#!?= +-*/%$ÄÜÖÆÑÅ SPACE COPY POSI RET RESET DOOR............ ↑ To set a display position for a PRESET ID Move the cursor to POSI and press the CAM (SET) key. The PRESET ID blinks and the display position set menu appears. Using the joystick, move the ID to the desired position on the screen, then press the MON (ESC) key.
● Dwell Time Setting Preset setting menu • Move the cursor to DWELL TIME and set a dwell time by moving the joystick to the left or right. Dwell time changes as follows: 2S 3S 5S 10S 30S 1MIN 2MIN 3MIN 4MIN The letter S signifies second(s) and MIN minute(s). PRESET NO.15*H POSITION SET PRESET ID ALC/MANUAL DWELL TIME SCENE FILE RET ● Scene File Setting ON ALC 2S 1 DEL Preset setting menu 1.
■ Deleting Preset Positions Setup menu 1. Move the cursor to PRESET 1* and select the position number to be deleted by moving the joystick. *** SET UP MENU *** PRESET 1* MAP HOME POSITION SELF RETURN AUTO MODE FLIP-A-CHIP LOCAL/REMOTE 15 10MIN AUTO PAN ON LOCAL CAMERA 2. Press the CAM (SET) key to display the preset setting menu. Preset setting menu PRESET NO.15*H POSITION SET PRESET ID ALC/MANUAL DWELL TIME SCENE FILE RET 3. Move the cursor to DEL and press the CAM (SET) key.
■ Auto Mode Setting Setup menu 1. To set auto mode Move the cursor to AUTO MODE and select a mode by moving the joystick to the left or right. Modes change as follows: OFF SEQ SORT AUTO PAN *** SET UP MENU *** PRESET 1* MAP HOME POSITION SELF RETURN AUTO MODE FLIP-A-CHIP LOCAL/REMOTE 15 10MIN AUTO PAN ON LOCAL CAMERA 2. When AUTO PAN is selected, set details as follows: Move the cursor to AUTO PAN and press the CAM (SET) key to display the AUTO PAN setting menu.
5. To set endless turn ON/OFF Move the cursor to ENDLESS, and move the joystick to the left or right to set endless turn ON or OFF. ON: The camera pans from the start position to the end position, then keeps rotating in the same direction to return to the start position. OFF: The camera pans from the start position to the end position, then rotates backward to the start position. This movement is repeated over and over. 6.
■ Camera Setting Setup menu 1. To display the Camera Setting Menu *** SET UP MENU *** • Move the cursor to CAMERA , and press the CAM (SET) key. The camera setting menu is displayed. PRESET 1* MAP HOME POSITION SELF RETURN AUTO MODE FLIP-A-CHIP LOCAL/REMOTE 15 10MIN AUTO PAN ON LOCAL CAMERA Camera setting menu ** SET UP ** CAMERA ID OFF ALC/MANUAL ALC SHUTTER --AGC ON SENS UP OFF SYNC INT WHITE BAL ATW MOTION DET OFF AF MODE MANUAL RET SPECIAL 2. Camera Identification Setting (CAMERA ID) 1.
• The positioning of the CAMERA ID stops at the edges of the screen. • The CAMERA ID moves faster when the joystick is kept pressed for more than 0.5 seconds. • To return to SET UP for setting other items, move the cursor to RET, and press the CAM (SET) key. CAMERA ID.-0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ ().,'":;&#!?= +-*/%$ÄÜÖÆÑÅ SPACE ---- POSI RET RESET CAM1....... ↑ CAMERA ID.-0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ ().,'":;&#!?= +-*/%$ÄÜÖÆÑÅ SPACE ---- POSI RET RESET CAM1....... ↑ 3.
(2) ALC Mode with SUPER-D OFF 1. Move the cursor to the SUPER-D parameter and select OFF. (When you select MANUAL, SUPER-D is not available.) The item MASK SET appears on the menu. Blinking 2. Move the cursor to MASK SET and press the CAM (SET)key. The 48 mask areas appear on the monitor screen. The cursor is blinking in the top left corner of the screen. 3. Move the cursor to the area where backlight is bright and press the CAM (SET) key to mask that area. The mask turns white.
Camera setting menu 4. Shutter Speed Setting (SHUTTER) Note: When ON is selected for SUPER-D on the ALC CONT menu, this item is not available. To select electronic shutter speed, select OFF for SUPER-D in the menu. 1. Display SET UP on the monitor screen. If necessary, refer to Setup Menu Display on page 10 for details on displaying the SET UP menu on the monitor screen. 2. Move the cursor to SHUTTER and select the electronic shutter speed by using the joystick.
Camera setting menu 7. Synchronization Setting (SYNC) 1. Display SET UP on the monitor screen. If necessary, refer to Setup Menu Display on page 10 for details on displaying the SET UP menu on the monitor screen. 2. Move the cursor to SYNC and select line-lock (LL) or internal (INT) by using the joystick. Important Notice: 1. The priority of SYNC modes is as follows; 1. Multiplexed vertical drive (VD2) (highest priority) 2. Line-lock (LL) 3. Internal sync (INT) (lowest priority) 2.
8. Move the cursor to FINE by using the joystick. The cursor starts blinking. 9. Use the joystick to match the vertical phase for both video output signals as closely as possible. Notes: • When the “|” cursor reaches the “+” end, it jumps back to “–”. At the same time, COARSE is incremented by one step to enable a continuous adjustment. The reverse takes place when the “|” cursor reaches the “–” end. • When the joystick is kept to the right or left for more than one second, the “|” cursor moves quickly.
7. Move the cursor to “B.” Use the joystick to obtain the optimum amount of blue gain. The “I” cursor moves to the left or right. 8. Move the cursor to RET by using the joystick and press the CAM (SET) key to return to SET UP. Camera setting menu (2) Automatic White Balance Control Mode (AWC) 1. Display SET UP on the monitor screen. (Refer to Setup Menu Display on page 10 for details on displaying the SET UP menu on the monitor screen.
9. Motion Detector Setting (MOTION DET) Camera setting menu ** SET UP ** 1. Display SET UP on the monitor screen. (Refer to Setup Menu Display on page 10 for details on displaying the SET UP menu on the monitor screen.) 2. Move the cursor to MOTION DET and select ON or OFF by using the joystick. 3. When you select ON, press the CAM (SET) key to display the motion detect setup menu. You can mask the areas in this menu.
Important Notices: • The object of motion detection should meet the following conditions. 1) It should be larger than 1/48 of the size of the picture screen. 2) The contrast ratio (at max. detection level) between the object and the background picture on the screen should be more than 5%. 3) The time it takes the object to move from one end of the screen to the other should be more than 0.1 seconds. • Also under the following conditions, mask or adjust the detection level to prevent malfunction.
Camera setting menu 11.Special Menu (SPECIAL) This menu lets you adjust and set up the video signal of the camera to meet your requirements. • Display SET UP on the monitor screen. (Refer to Setup Menu Display on page 10 for details on displaying the SET UP on the monitor screen.) • Move the cursor to SPECIAL and press the F2 button of the WVCU550A. The special menu appears on the monitor screen. (For the WV-RM70, keep pressing the Right and Left switches simultaneously for more than 2 seconds.
(4) Camera Picture Setting (UP SIDE DOWN) 1. In this menu, it is possible to turn the picture upside down. Use this menu as described below. 2. Move the cursor to UP SIDE DOWN and select ON by using the joystick. The picture will be shown upside down, but the sides will not be reversed. ** SPECIAL ** CHROMA GAIN AP GAIN PEDESTAL UP SIDE DOWN REFRESH CAMERA RESET ....I.... ....I.... .I.......
INSTALLATION 2. Precaution: The following installations should be made by qualified service personnel or system installers. Setting the switches Set the switches as follows: DIP φ DIP 1 DIP 2 DIP 3 DIP Switches Setting the camera switches (only for WV-CSR650) • To reset the communication parameters to the factory preset values, for example, when operating multiple cameras in a daisy chain connection, set the switches inside the camera as shown in the table below. ON OFF 1.
PAL or NTSC DIP φ OFF NTSC ON PAL b. Top cable exit Note: The dip switch φ is not for changing NTSC to PAL or PAL to NTSC. This switch is set at factory. Do not change the setting of this switch. The factory setting is ON. 3. Assemble the camera Reverse the disassembly procedure. Take care not to cut any cables. Precautions: 1. The following installation work should be referred to qualified service personnel or system installers and must conform with local codes. 2.
4. Hook the Fall prevention wire on the camera mounting angle. 2. Follow the instructions given here to ensure that the camera and camera mounting angle are installed safely. 3. When removing the camera from the camera mounting angle, loosen and press up the camera fixing screw (M3) by using a screwdriver. Be sure to match the wire with the fall prevention wire fixing angle as shown below. Fall Prevention Wire Fixing Angle 7. Fix the decoration cover to the camera mounting angle. a.
CONNECTIONS Precaution: The following connections should be made by qualified service personnel or system installers in accordance with all local codes. 220 - 240V AC (WV-CS650, WV-CSR650) 24V AC (WV-CS654) Data cable (Only for WV-CSR650) Video Output Cable RS485 cable BNC Plug Coaxial Cable (5C-2V) To Video IN (CAMERA IN) BNC Plug ✻ The coaxial cable length (RG-6/U, 5C-2V) for the connection is up to 1 200 meter (4,000 ft.
● RS485 site connection Brown GND Red Data Transmission Orange Yellow Data Reception Green T (B) T (A) R (B) R (A) For daisy chain connection of multiple cameras, make sure to match each male connector with its female counterpart. Note: Use the cable that is described below for RS485 site communication by using WV-CSR650. • Shielded, twisted pair cable • Low impedance • Wire gauge size is thicker than AWG #22 (0.33mm2).
SYSTEM CONNECTIONS Combination Camera WV-CS650 WV-CS654 WV-CSR650 only or other models Max.
PREVENTION OF BLOOMING AND SMEAR , , , , , , When the camera is aimed at a bright light, such as a spotlight, or a surface that reflects bright light, smear or blooming may appear. Therefore, the camera should be operated carefully in the vicinity of extremely bright objects to avoid smear or blooming.
Panning Range Panning Angle Setting Panning mode Panning Speed Tilting Range Tilting Mode Tilting Speed Controls 360° Endless Possible (in Auto-Pan mode) Manual/Sequential Position/Sort Position/Auto Pan Manual : Approx. 3°/s - 120°/s eight steps Sequence Position : Maximum approx. 240°/s 0 - 90° Manual/Sequential Position/Sort Position Manual : Approx. 1.5°/s - 60°/s. eight steps Sequential Position : Maximum approx.
Matsushita Electric Industrial Co., Ltd. Central P.O.
