Installation Guide Included Installation Instructions Network Camera WV-SW155 WV-SW155M/ WV-SW155MA WV-SW152/ WV-SW152M Model No. WV-SW155 Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number is abbreviated in some descriptions in this manual. This document is the Installation Guide for use in other countries except Japan.
For Europe For Canada CAN ICES-3(A)/NMB-3(A) For U.S.A NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Contents Important safety instructions.......................................................................................................... 4 Limitation of liability........................................................................................................................ 5 Disclaimer of warranty.................................................................................................................... 5 Preface.......................................................................
Important safety instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 6) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 7) Only use attachments/accessories specified by the manufacturer.
Limitation of liability THIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THE THIRD PARTY'S RIGHT. THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).
Preface The network cameras WV-SW155/WV-SW155M/WV-SW155MA/WV-SW152/WV-SW152M are designed to operate using a PC on a network (10BASE-T/100BASE-TX), and can be installed under eaves (sheltered outdoor). By connecting to a network (LAN) or the Internet, images from the camera can be monitored on a PC via a network.
About the user manuals There are 2 sets of operating instructions for the WV-SW155, WV-SW155M, WV-SW155MA, WV-SW152, WV-SW152M as follows. • Installation Guide: Explains how to install and connect devices. • Operating Instructions (included in the CD-ROM): Explains how to perform the settings and how to operate this camera. SW155, SW155M, SW155MA, SW152, SW152M shown in the instructions and illustrations used in these operating instructions indicates the WV-SW155, WV-SW155M, WV-SW155MA, WV-SW152, WV-SW152M.
Others: CD-ROM drive (It is necessary to read the operating instructions and use the software on the provided CD-ROM.) DirectX® 9.0c or later Adobe® Reader® (It is necessary to view the PDF file on the provided CD-ROM.) IMPORTANT: • When using a PC that does not meet the above requirements, displaying of images may become slower or the web browser may become inoperable.
Copyright Distributing, copying, disassembling, reverse compiling and reverse engineering of the software provided with this product are all expressly prohibited. In addition, exporting any software provided with this product violating export laws is prohibited. Network security As you will use this unit connected to a network, your attention is called to the following security risks.
Precautions Refer installation work to the dealer. Installation work requires technique and experiences. Failure to observe this may cause fire, electric shock, injury, or damage to this product. Be sure to consult the dealer. Stop the operation immediately when something is wrong with this product.
Do not touch this product or the connected cables during thunder. (even in the process of work) Failure to observe this may cause electric shock. Turn the power off when cleaning this product. Failure to observe this may cause injury. [Precautions for use] This product has no power switch. When turning off the power, turn off a PoE hub or remove a network cable. To keep on using with stable performance Do not use this product in hot and humid conditions for a long time.
• When some SDHC/SD memory cards are used with this product, the product may not work properly or performance deterioration may be caused. Use the SDHC/SD memory cards recommended in page 37. Code label The code labels (accessory) are required at inquiry for trouble. Use caution not to lose these labels. It is recommended to paste one of the labels onto the CD-ROM case.
Precautions for installation Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation. This product is designed to be installed under eaves. Install the product under eaves to avoid direct sunlight. Installing place Contact your dealer for assistance if you are unsure of an appropriate place in your particular environment.
Do not remove or loosen the internal camera screws Do not loosen the internal camera screws. Otherwise, water exposure may cause damage or malfunction of camera, or camera dropping may result in injury. Radio disturbance When this product is used near TV/radio antenna, strong electric field or magnetic field (near a motor, a transformer or a power line), images may be distorted and noise sound may be produced. PoE (Power over Ethernet) Use a PoE hub/device that is compliant with IEEE802.3af standard.
Major operating controls Enclosure Dome cover SDHC/SD memory card slot Network cable Initial set button Access indicator (lit when accessing) Lens SD memory card error indicator (lit when data cannot be saved) Link indicator (lit when linking) About the initial set button After turning off the power of the camera, turn on the power of the camera while holding down this button, and wait for around 5 seconds or more without releasing the button.
Removing the enclosure IMPORTANT: • Remove the cover film attached to the dome cover after the camera installation is completed. After removing the cover film, do not touch the dome cover with your hands. z Loosen the 3 enclosure fixing screws (M3) using the tamperproof screw bit (accessory). • One of the screws is loosened after taking off the screw cover. x Remove the enclosure.
Preparations When installing the camera on a ceiling or a wall, there are three methods as specified below. • Directly mounting to a ceiling or a wall • Use the supplied mount bracket • Use the one-gang junction box IMPORTANT: • Procure 3 screws (M4) to secure the camera or the mount bracket (accessory) to a ceiling or a wall according to the material of the installation area. Do not use wood screws and nails.
Method of camera installation Installing the camera directly on the ceiling or wall Note: • Use the installation template label (accessory) with the side with the arrow facing you. • Ceiling installation: Place the installation template label so that the "" is pointing to the front of the camera (the lens side). • Wall installation: Place the installation template label so that the "" is pointing down.
n Ceiling n Wall Using the mount bracket (accessory) Note: • When the camera is mounted on the ceiling or wall with a hole for cable running and the cables are passed through a conduit, the mount bracket is used. • The female thread for conduit is compliant with ANSI NPSM (parallel pipe threads) 3/4" or G3/4 of ISO 228-1. • Ceiling installation: The mount bracket shall be mounted with aligning the front side (the lens side) of the camera with the position of the arrow in "".
Tamperproof screw hole Cable access hole Place the installation template label (accessory) on the ceiling or wall, mark the hole for the cable to be passed through and for the fixing screws (3 places), then open the holes. Remove the installation template label, and mount the mount bracket with 3 fixing screws (locally procured).
Using a one-gang junction box • Secure the mount bracket (accessory) to the one-gang junction box built in a ceiling or a wall. [Mounting hole pattern] One-gang junction box 83.5 mm {3-9/32"} Mount bracket (accessory) Note: • Ceiling installation: The mount bracket shall be mounted with aligning the front side (the lens side) of the camera with the position of the arrow in "". • Wall installation: The mount bracket shall be mounted with "" facing upward.
Insert/remove an SDHC/SD memory card IMPORTANT: • When inserting an SDHC/SD memory card, make sure the direction. • Before removing the SDHC/SD memory card, make sure to select “Not use” for “SD memory card” on the [SD memory card] tab of the “Basic” page on the setup menu first. (☞ Operating Instructions (included in the CD-ROM)) z Remove the enclosure. (☞ Page 16) x Insert an SDHC/SD memory card fully into the SDHC/SD memory card slot until a click is heard. c Attach the enclosure to the camera.
Connection Before starting the connection, turn off the power of the devices to be connected. Check and prepare the required devices and cables for connection. Note: • Refer to pages 26 and 27 when using the mount bracket (accessory). • Refer to pages 26 and 27 when using the conduit. z Connect a LAN cable (category 5 or better, straight) between a PoE device (such as a hub) and the network connector of the camera.
IMPORTANT: • Use all 4 pairs (8 pins) of the LAN cable. • The maximum cable length is 100 m {328 feet}. • Make sure that the PoE device in use is compliant with IEEE802.3af standard. • When the LAN cable is disconnected once, reconnect the cable after about 2 seconds. When the cable is quickly reconnected, the power may not be supplied from the PoE device. Waterproof treatment for the cable joint sections Adequate waterproof treatment is required for the cables when installing the camera outdoors.
Connection example PoE device (hub) LAN cable (category 5 or better, straight) LAN cable PC (category 5 or better, straight) LAN cable (category 5 or better, straight) LAN cable (category 5 or better, straight) IMPORTANT: • Use a switching hub which is compliant with 10BASE-T/100BASE-TX. • When connecting WV-SW155M/WV-SW155MA cameras, use a PoE hub with M12 connectors.
Installation Camera mounting z Remove the enclosure. (3 screws) (☞ Page 16) x Connect the cables to the camera. (☞ Pages 23 and 24) • Waterproof the connecting portion. (☞ Page 24) c Secure the camera with 3 screws (M4) (locally procured). n Ceiling n Wall IMPORTANT: • Do not touch the lens. • When tightening the screws, be careful to ensure that the cables does not tangle the cables. z Connect each cable.
Conduit attachment Attachment for female thread Camera Fixing screws Mount bracket Network cable Conduit n Wall n Ceiling z Connect each cable. • Apply waterproof treatment to all connections. (☞ Page 24) x Secure the mount bracket to the one-gang junction box. (2 screws (M4) (locally procured)) c Secure the camera to the mount bracket with 3 fixing screws (accessory). (Recommended tightening torque: 1.
Using the side cable access hole When installing the camera directly on the ceiling or wall with cables exposed, cut off a portion of the mount bracket to open a cable access hole.
Adjustment z Adjust the camera angle. When determining the camera angle, repeat fine adjustments by gradually moving the panning table and tilting table. • Attach the lens adjuster (accessory) to the lens and adjust the direction of the lens. Attach the wider end of the lens adjuster to the lens. • Do not touch the lens with your hand when making adjustments. • Make adjustments to the direction of the lens while confirming the picture displayed on computer’s monitor.
Note: • Depending on the vertical/horizontal angle used, the edges of the camera may be projected. • Use Extra Zoom when you want to adjust the angular field of view on the "Tele" side. When VGA or a lower resolution is selected, the angular field of view can be adjusted without deterioration in the image quality.
Attaching the enclosure z Attach the enclosure to the camera by using the tamperproof screw bit (accessory) to tighten the 3 enclosure fixing screws (M3). (Recommended tightening torque: 0.8 N·m {0.59 lbf·ft}) n Ceiling n Wall Screw cover Enclosure fixing screws Enclosure fixing screws x Close the screw cover. c Remove the cover film completely. IMPORTANT: • When attaching the enclosure the focus may be slightly disturbed. If this occurs, remove the enclosure and make the necessary adjustments.
Configure the network settings Configuring the camera so that it can be accessed from a PC The following are descriptions for when the camera with default settings is configured. If you are using firewall software on your PC, the Setup Program may not be able to find any cameras on your network. Configure the setting of the camera after temporarily invalidating the firewall software.
c Select the camera you want to configure, and click [Access Camera]. Note: • When cameras are displayed in [Panasonic IP Setting] screen, click the camera with same MAC address as the MAC address printed on the camera that you want to configure. v If the installation screen of the viewer software “Network Camera View 4S” is displayed, follow the instructions of the wizard to start the installation. (The viewer software is installed from the camera.) • The “Live” page will be displayed.
Troubleshooting Before asking for repairs, check the symptoms with the following table. Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table or a problem is not described below. Symptom Power is not turned on. 34 Cause/solution • Are the PoE device and the network cable of the camera connected using a LAN cable? → Check whether the connection is appropriately established.
Specifications • Basic Power source: Power consumption: Ambient operating temperature: Ambient operating humidity: Waterproof: Shock resistance: Dimensions: Mass: Finish: • Camera Image sensor: Effective pixels: Scanning area: Scanning system: Minimum illumination: PoE (IEEE802.
Day & Night (electrical): White balance: Digital noise reduction: Video analytics Face detection*: Privacy zone: VIQS: Camera title on screen: Off/Auto ATW1/ ATW2/ AWC High/Low On/Off (with the XML notification setting) On/Off (up to 2 zones available) On/Off Up to 20 characters (alphanumeric characters, marks) On/Off Video motion detection (VMD alarm): On/Off, 4 areas available * To use the "XML notification" and "Face detection" functions, you need to install the extension software.
Image compression method*1 : H.264 Image quality: Low/Normal/Fine Transmission type: Unicast/Multicast Bit rate: Constant bit rate/Best effort: 64 kbps/ 128 kbps/ 256 kbps/ 384 kbps/ 512 kbps/ 768 kbps/ 1024 kbps/ 1536 kbps/ 2048 kbps/ 3072 kbps/ 4096 kbps/ SW155M 8192 kbps SW155 Frame rate: 1 fps/ 3 fps/ 5 fps/ 7.
*3 When using IPv6 for communication, use Microsoft® Windows® 7 or Microsoft® Windows Vista®. *4 For further information about compatible devices, refer to our website (http://security.panasonic.com/pss/security/support/info.html).
Standard accessories Installation Guide (this document).......................................................1 set Important Safety Instructions..............................................................1 pc. Warranty card.....................................................................................1 set CD-ROM*1.........................................................................................1 pc. Code label*2................................................................................
Disposal of Old Equipment and Batteries Only for European Union and countries with recycling systems These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries must not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points in accordance with your national legislation.
