Installation Guide Included Installation Instructions Network Camera Model No. WV-SP509/WV-SP508 Lens: Option (This illustration represents WV-SP509.) Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number is abbreviated in some descriptions in this manual. This document is the Installation Guide for use in other countries except Japan.
WARNING: • To prevent injury, this apparatus must be securely attached to the floor/wall/ceiling in accordance with the installation instructions. • To prevent fire or electric shock hazard, do not expose this apparatus to rain or moisture. • The installation shall be carried out in accordance with all applicable installation rules. • The connections should comply with local electrical code. For Canada CAN ICES-3(A)/NMB-3(A) For U.S.
For Europe We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standard or other normative document following the provisions of Directive 2004/108/EC. Wir erklären in alleiniger Verantwortung, daß das Produkt, auf das sich diese Erklärung bezieht, mit der folgenden Norm oder normativen Dokument übereinstimmt. Gemäß den Bestimmungen der Richtlinie 2004/108/EC.
Contents Important safety instructions......................................................................................................... 5 Limitation of liability ....................................................................................................................... 6 Disclaimer of warranty ................................................................................................................... 6 Preface .......................................................................
Important safety instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Limitation of liability THIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THE THIRD PARTY'S RIGHT. THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).
About notations The following notations are used when describing the functions limited for specified models. The functions without the notations are supported by all models. SP509 SP508 : The functions with this notation are available when using the model WV-SP509. : The functions with this notation are available when using the model WV-SP508. Main functions H.264 and JPEG triple encoding H.264 dual stream output and JPEG output can be simultaneously provided. * H.264 stream1: 1920x1080/ max. 30 fps H.
About the user manuals There are 2 sets of operating instructions for the WV-SP509, WV-SP508 as follows. • Installation Guide: Explains how to install and connect devices. • Operating Instructions (included in the CD-ROM): Explains how to perform the settings and how to operate this camera. Adobe® Reader® is required to read these operating instructions on the provided CD-ROM. When the Adobe Reader is not installed on the PC, download the latest Adobe Reader from the Adobe web site and install it.
IMPORTANT: • When using a PC that does not meet the above requirements, displaying of images may become slower or the web browser may become inoperable. • Audio may not be heard if a sound card is not installed on a PC. Audio may be interrupted depending on the network environment. • Microsoft Windows 7 Starter, Microsoft Windows Vista Starter and Microsoft Windows XP Professional 64-bit Edition are not supported. • When using IPv6 for communication, use Microsoft Windows 7 or Microsoft Windows Vista.
Network security As you will use this unit connected to a network, your attention is called to the following security risks. q Leakage or theft of information through this unit w Use of this unit for illegal operations by persons with malicious intent e Interference with or stoppage of this unit by persons with malicious intent It is your responsibility to take precautions such as those described below to protect yourself against the above network security risks.
Precautions Refer installation work to the dealer. Installation work requires technique and experiences. Failure to observe this may cause fire, electric shock, injury, or damage to the product. Be sure to consult the dealer. Avoid installing this bracket in the locations where salt damage occurs or corrosive gas is produced. Otherwise, the mounting portions will deteriorate and accidents such as a fall of this product may occur. Stop the operation immediately when something is wrong with this product.
Do not rub the edges of metal parts with your hand. Failure to observe this may cause injury. Do not touch this product, the power cable or the connected cables during thunder. (Including during installation work) Failure to observe this may cause electric shock. Keep SDXC/SDHC/SD memory cards (option) away from infants and children. Otherwise, they may swallow the cards by mistake. In this case, consult a doctor immediately. Do not damage the power cable.
data on the SD memory card will be deleted when formatted. If an unformatted SD memory card or an SD memory card formatted with other devices is used, this product may not work properly or performance deterioration may be caused. Refer to the Operating Instructions (included in the CD-ROM) for how to format a SD memory card. • When some SD memory cards are used with this product, the product may not work properly or performance deterioration may be caused.
Precautions for Installation Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation. This camera is designed to be used indoors. This camera is not operable outdoors. Do not expose this camera to direct sunlight for hours and do not install the product near a heater or an air conditioner. Otherwise, it may cause deformation, discoloration and malfunction.
Screw tightening • The screws and bolts must be tightened with an appropriate tightening torque according to the material and strength of the installation area. • Do not use an impact driver. Use of an impact driver may damage the screws or cause tightening excessively. • When a screw is tightened, make the screw at a right angle to the surface. After tightening the screws or bolts, perform visual check to ensure tightening is enough and there is no backlash.
Major operating controls W ALC lens connector Lens (option) SD memory card slot W ABF SDCARD LOCK Tripod mount base Slide cover Clamp for SD memory card Auto back focus button (ABF) W ABF Tripod mount base 16
Network connector Audio output connector 10BASE T/100BASE-TX Access indicator (blinks when accessing) AUDIO OUT MIC/LINE IN INITIAL SET Microphone/line input connector INITIAL SET button Link indicator (lit when linking) ACT LINK MONITOR OUT SD CARD/ABF EXT I/O POWER 12V = IN Power indicator 12 V DC power supply terminal Monitor for adjustment Output connector GND 4 3 2 1 ALARM IN 1/DAY/NIGHT IN ALARM IN 3/AUX OUT ALARM IN 2/ALARM OUT EXT I/O terminals SD memory card
Lens mounting Slowly rotate the lens clockwise to mount the lens and connect the lens cable to the ALC lens connector of the camera. ALC lens connector Zoom lock knob CS-mount lens (option) Protruded portion from mount face: ø20 mm {25/32 inches} or less 3URWUXGHG SRUWLRQ IURP ƅDQJH IDFH 4.5 mm {5/32 inches} or less T W 1 3 Focus ring Optional dedicated lens Product name ALC lens for 1/3 type CCD cameras 2x varifocal (High resolution) Pin No.
Note: • The most common use of a varifocal lens and a zoom lens Note that the adjustment method is different depending on the type. For further information, refer to the operating instructions for the lens to be used. When using 8x or 10x lens, adjust the back focus after positioning the zoom ring at the "W" end and positioning the focus ring at a step short of the "F" end.
Insert/remove a SD memory card (WV-SP509 only) IMPORTANT: • When inserting a SD memory card, make sure the direction. • Before removing the SD memory card, make sure to select “Not use” for “SD memory card” on the [SD memory card] tab of the “Basic” page on the setup menu first. (☞ Operating Instructions (included in the CD-ROM)) z Open the slide cover on the side of the camera, and then insert a SD memory card into the SD memory card slot.
Installation Connect the safety wire The following is an example of safety wire connection. IMPORTANT: • Be sure to install the safety wire. Ask your dealer for installation. For mounting on ceiling z Remove the tripod mount base on the top of the camera. Mounting screws Tripod mount base Safety wire plate for ceiling (accessory) x Align the tripod mount base with the safety wire plate for ceiling (accessory) and attach them to the camera with the mounting screws.
For mounting on wall z Put the tripod mount base on the bottom of the camera. Secure the safety wire lug for wall (accessory) to the camera mount screw hole with the wire lug fixing screw (accessory). IMPORTANT: • Be sure to use the provided fixing screws for the safety wire lug and the removed screws for the camera mount base. When using different length screws, it may damage the camera or cause the camera to fall. (Recommended tightening torque: 0.39 N·m {0.
Camera mounting The camera is mounted on the camera mount bracket (locally procured) and the safety wire is secured. IMPORTANT: • The installation area shall be strong enough to hold the camera and camera mount bracket. • The camera mount bracket (locally procured) shall be mounted on the foundation part of the construction or a part with adequate strength. • To prevent the mounting strength from becoming lower, do not use wooden screws to secure the camera mount bracket (locally procured).
IMPORTANT: • The safety wire shall be adjusted to remove slack. • Be sure to install the safety wire to prevent a fall of the camera resulting in injury or accidents in case the camera comes off. • To prevent the mounting strength from becoming lower, do not use wooden screws to secure the safety wire. Washer (accessory) Spring washer (accessory) Recommended screw M4 Minimum pull-out strength 196 N {44.
Connection Caution: • ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or LIMITED POWER SOURCE (IEC/EN/UL/CSA 60950-1). Before starting the connection, turn off the power of this camera and the devices to be connected. Before start the connection, prepare the required devices and cables. z Connect the RCA pin cable to the monitor output connector for adjustment on the rear (only for adjustment of the angle field of view). Connect to the video monitor, etc.
v Connect external devices to the EXT I/O terminal. Strip range When connecting an external device, remove 9 mm - 10 mm {11/32 inches - 13/32 inches} of the outer jacket of the cable 9 mm - 10 mm and twist the cable core to prevent the short circuit first. {11/32 inches - 13/32 inches} Specification of cable (wire): 22 AWG - 28 AWG Single core, twisted • Check whether the stripped part of the wire is not exposed and is securely connected.
n Connect the power supply. IMPORTANT: • The 12 V DC power supply shall be insulated from the commercial AC power. • The operating sound might be heard when the power is turned on, however it does not indicate any malfunction. When using 12 V DC power supply* 10BASE T/100BASE-TX AUDIO OUT q Loosen the screw of the power cord plug (accessory). w Connect the cable of the 12 V DC power supply* to the power cord plug.
When using PoE (IEEE802.3af compliant) Connect a LAN cable (category 5 or better, straight, STP*) between a PoE device (such as a hub) and the network connector of the camera. * For Europe. IMPORTANT: • Use all 4 pairs (8 pins) of the LAN cable. • The maximum cable length is 100 m {328 feet}. • Make sure that the PoE device in use is compliant with IEEE802.3af standard. • When connecting both the 12 V DC power supply and the PoE device for power supply, 12 V DC will be used for power supply.
Configure the network settings Configuring the camera so that it can be accessed from a PC The following are descriptions for when the camera with default settings is configured. If you are using firewall software on your PC, the Setup Program may not be able to find any cameras on your network. Configure the setting of the camera after temporarily invalidating the firewall software.
c Select the camera you want to configure, and click [Access Camera]. Note: • When cameras are displayed in [Panasonic IP Setting] screen, click the camera with same MAC address as the MAC address printed on the camera that you want to configure. v If the installation screen of the viewer software “Network Camera View 4S” is displayed, follow the instructions of the wizard to start the installation. (The viewer software is installed from the camera.) • The “Live” page will be displayed.
Troubleshooting Before asking for repairs, check the symptoms with the following table. Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table or a problem is not described below. Symptom Cause/solution Reference pages Power is not turned on. When using DC power supply • Is 12 V DC power supply connected to the power supply terminal? Check whether the connection is appropriately established.
Specifications ● Basic Power source: Power consumption: Ambient operating temperature: Ambient operating humidity: Monitor output (for adjusting the angular field of view): EXT I/O terminal cable: Microphone/Line input SP509 For microphone input : For line input : Audio output SP509 : Dimensions: Mass: Finish: 12 V DC, PoE (IEEE802.
BW: Super Dynamic: Dynamic range: Gain (AGC): Adaptive black stretch: Light control mode setting: Shutter speed: Auto slow shutter: Day & Night (IR) SP509 : Day & Night (electrical) SP508 White balance: Digital noise reduction: Video analytics Face detection*1: Privacy zone: VIQS: Camera title on screen: Video motion detection (VMD alarm): Back focus Adjustment: ALC lens drive: Lens mount: 0.3 lx {0.03 footcandle} (F1.4, Auto slow shutter: Off (1/30 s), Gain: On(High)) 0.02 lx {0.002 footcandle} (F1.
Image compression method: *1 Transmission interval: Transmission the image cut out H.264 Image quality: Low/ Normal/ Fine Transmission type: Unicast/Multicast Bit rate: Constant bit rate: 64 kbps/ 128 kbps/ 256 kbps/ 384 kbps/ 512 kbps/ 768 kbps/ 1024 kbps/ 1536 kbps/ 2048 kbps/ 3072 kbps/ 4096 kbps/ 6144 kbps/ 8192 kbps/ 10240 kbps/ 12288 kbps/ 14336 kbps Frame rate: 1 fps/ 3 fps/ 5 fps/ 7.
SD memory card (option) SP509 Cellular phone compatibility: Mobile terminal compatibility: (As of October, 2013)*4 : SDXC memory card: 64 GB SDHC memory card: 4 GB, 8 GB, 16 GB, 32 GB SD memory card: 2 GB (except miniSD card and microSD card) JPEG image, AUX control (by access level) iPad, iPhone, iPod touch (iOS 4.2.1 or later) Android™ mobile terminals *1 Transmission for 2 streams can be individually set in the same compression method.
Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.
