Installation Guide Network Camera WV-SP105, WV-SP102 WV-SP105E, WV-SP102E Model No. P105 WV-S (This illustration represents WV-SP105.) Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number is abbreviated in some descriptions in this manual.
WARNING: • Apparatus shall be connected to a mains socket outlet with a protective earthing connection. • The mains plug or an appliance coupler shall remain readily operable. • To prevent fire or electric shock hazard, do not expose this apparatus to rain or moisture. • The apparatus should not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, should be placed on the apparatus.
We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standards or other normative documents following the provisions of Directives 2006/95/EC and 2004/108/EC. Wir erklären in alleiniger Verantwortung, daß das Produkt, auf das sich diese Erklärung bezieht, mit den folgenden Normen oder normativen Dokumenten übereinstimmt. Gemäß den Bestimmungen der Richtlinie 2006/95/EC und 2004/108/EC.
Contents Important safety instructions.......................................................................................................... 5 Limitation of liability........................................................................................................................ 6 Disclaimer of warranty.................................................................................................................... 6 Preface.......................................................................
Important safety instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Limitation of liability THIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THE THIRD PARTY'S RIGHT. THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).
Preface The network cameras WV-SP105, WV-SP102, WV-SP105E and WV-SP102E are designed to operate using a PC on a network (10BASE-T/100BASE-TX). By connecting to a network (LAN) or the Internet, images from the camera can be monitored on a PC via a network.
About the user manuals There are 2 sets of operating instructions for the WV-SP105, WV-SP102 (NTSC model) and WV-SP105E, WV-SP102E (PAL model) as follows. • Installation Guide: Explains how to install and connect devices. • Operating Instructions (PDF): Explains how to perform the settings and how to operate this camera. Adobe® Reader® is required to read these operating instructions (PDF) on the provided CD-ROM.
Important: • When using a PC that does not meet the above requirements, displaying of images may become slower or the web browser may become inoperable. • Microsoft® Windows® XP Professional 64-bit Edition is not supported. • When using IPv6 for communication, use Microsoft® Windows® 7 or Microsoft® Windows Vista®.
Network security As you will use this unit connected to a network, your attention is called to the following security risks. q Leakage or theft of information through this unit w Use of this unit for illegal operations by persons with malicious intent e Interference with or stoppage of this unit by persons with malicious intent It is your responsibility to take precautions such as those described below to protect yourself against the above network security risks.
Periodic inspections shall be conducted. Rust on the metal parts or screws may cause a fall of this product resulting in injury or accidents. Consult the dealer for the inspections. Turn the power off when do wiring of this product. Failure to observe this may cause electric shock. In addition, short circuit or wrong wiring may cause fire. Do not use this product in an inflammable atmosphere. Failure to observe this may cause an explosion resulting in injury.
Cleaning this product body Be sure to turn off the power before cleaning. Do not use strong abrasive detergent when cleaning this product. Otherwise, it may cause discoloration. When using a chemical cloth for cleaning, read the caution provided with the chemical cloth product. When the dirt is hard to remove, use a mild detergent and wipe gently. When the dirt is hard to remove, use a mild detergent and wipe gently. Then, wipe off the remaining detergent with a dry cloth.
Precautions for Installation No responsibility will be taken by our company with respect to consequeces resulting from the use, damage or both of the camera. This product is designed to be used indoors. The product is not operable outdoors. Do not expose the product to direct sunlight for hours and do not install the product near a heater or an air conditioner. Otherwise, it may cause deformation, discoloration and malfunction. Keep the product away from water and moisture.
Angle adjustment Be sure to loosen the screw of the camera mount bracket when the camera angle is adjusted. If the camera angle is changed when the screw is tight, excessive force is applied to the camera mount bracket and this product, and accordingly they may be damaged. Be sure to tighten the fixing piece securely after camera angle adjustment.
Major operating controls Tripod screw hole Lens WV-SP105 Tripod screw hole Wire engaging hole Network connector Access indicator (blinking at accessing) Link indicator (Lights when the connection is being established) INITIAL SET 10BASE-T/ 100BASE-TX 12 V DC power cord terminals 12V IN INITIAL SET button ACT LINK POWER Power indicator (This illustration represents WV-SP105.
Installation Connect the safety wire If an installation area has sufficient strength (☞ page 17), secure the provided safety wire to the installation area. If not, procure another wire that can substitute for the safety wire (accessory). The following is an example of safety wire connection. Important: • Be sure to install the safety wire. Ask your dealer for installation. • Take care so that the camera does not roll over. Do not remove the camera cover film until the installation is completed.
Camera mounting The camera will be mounted on the camera mount bracket (locally procured). After the angular field of view is determined, the safety wire will be secured. Important: • The installation area shall be strong enough to hold the camera and camera mount bracket (locally procured). • The camera mount bracket (locally procured) shall be mounted on the foundation part of the construction or a part with adequate strength.
Attach the angle adjustment cover to the camera Important: • Angle adjustment cover (accessory) is intended for the tentative adjustment of angular field of view. Perform the final adjustment while viewing the images actually on a monitor. • The angle adjustment cover is dedicated to this product. z Build up the angle adjustment cover (accessory). Protrusions Hook Target sections Opening sections Target sections Opening sections w Fold the target sections inward.
Camera cover film Remove the camera cover film. Make sure that the hook is situated at the bottom, and place the angle adjustment cover over the camera. Fold the hook inward, and put the hook on the tripod screw hold for fixation. Camera cover film Remove the camera cover film. Make sure that the hook is situated at the top, and place the angle adjustment cover over the camera.
How to check the angular field of view z Check the shooting range with the angle adjustment cover attached to the camera. x You can see the camera adjustment cover as illustrated when you look toward the camera from a desired shooting area. Cross line disappears. (Shooting range) C B A Seen from Position A Opening section frame Cross line can be seen properly. Seen from Position B Opening section frame Cross line overlaps an opening section frame.
Remove the angle adjustment cover After determining the installation angle of the camera, remove the angle adjustment cover. Make sure the camera is secured to the camera mount bracket, and place the sticker (accessory) over the tripod screw hole on which the hook of the angle adjustment cover was put. Secure the safety wire on the ceiling or wall Secure the safety wire to the foundation part of the construction or a part with adequate strength (minimum pull-out strength 196 N {44.06 lbf}).
Ceiling Washer (accessory) Spring washer (accessory) Safety wire (accessory) Recommended screw M4 Minimum pull-out strength 196 N {44.06 lbf} Sticker (accessory) Safety wire (accessory) Recommended screw M6 Minimum pull-out strength 196 N {44.
Connection Caution: • FOR UL LISTED MODEL(S), ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY. Before starting the connection, turn off the power of this camera and the devices to be connected. Check and prepare the required devices and cables for connection. z Connect a LAN cable (category 5 or better, straight, 12V IN LAN cable INITIAL SET 10BASE-T/ 100BASE-TX STP*) to the network connector on the rear of the camera. * PAL models only ACT LINK x Connect the power cord.
Important: • Be sure to use the power cord plug (accessory) provided with this product. • Be sure to fully insert the power cord plug (accessory) into the 12 V DC power supply terminal. Otherwise, it may damage the camera or cause malfunction. • Mount the camera so that excessive force is not applied to the power cord. • Be sure to use an AC adaptor compliant with the Specifications regarding power source and power consumption (☞ p.29). ● When using PoE (IEEE802.
Connection example when connecting to a network using a PoE hub PoE device (hub) LAN cable (category 5 or better, straight, STP*) LAN cable (category 5 or better, straight, STP*) PC LAN cable (category 5 or better, straight, STP*) LAN cable (category 5 or better, straight, STP*) * PAL models only Important: • The camera is to be connected only to PoE networks without routing to the outside plant when using PoE.
Configure the network settings Install the software Before installing the software, refer to the readme file on the provided CD-ROM first. Software included on the provided CD-ROM • Panasonic IP setting software Configure the network settings of the camera. Refer to the following for further information. • Viewer Software "Network Camera View 4S" It is necessary to install the viewer software "Network Camera View 4S" to display images on a PC.
z Start the Panasonic IP setting software. x Click the [IP setting] button after selecting the MAC address/IP address of the camera to be configured. Note: • When using a DHCP server, the IP address assigned to the camera can be displayed by clicking the [Refresh] button of the IP setting software. • When a duplicate IP address is used, the corresponding MAC address/IP address will be displayed shaded. c Complete each network setup item and click the [Apply] button.
Troubleshooting Before asking for repairs, check the symptoms with the following table. Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table or a problem is not described below. Symptom Power is not turned on. 28 Cause/solution Reference pages When using DC power supply • Is 12 V DC power supply connect to the power supply terminal? → Check whether the connection is appropriately established.
Specifications ● Basic Power source: 12 V DC, PoE (IEEE802.3af compliant) Power consumption: WV-SP105 12 V DC*: 200 mA, PoE: 2.8 W (Class 2 device) WV-SP102 12 V DC*: 140 mA, PoE: 2.0 W (Class 2 device) * FOR UL LISTED MODEL(S), ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY.
Gain (AGC): On(Low)/ On(Mid)/ On(High)/ Off Adaptive black stretch: On/Off Light control mode setting: Indoor scene (50 Hz/60 Hz)/ ELC Maximum exposure time: WV-SP105: 1/30 s, 3/100 s, 3/120 s, 2/100 s, 2/120 s, 1/100 s, 1/120 s, 1/250 s, 1/500 s, 1/1000 s, 1/2000 s, 1/4000 s, 1/10000 s WV-SP102: 1/30 s, 3/100 s, 3/120 s, 2/100 s, 2/120 s, 1/100 s, 1/120 s, 1/250 s, 1/500 s, 1/1000 s, 1/2000 s, 1/4000 s, 1/8000 s Auto slow shutter: WV-SP105: Off(1/30 s), max. 2/30 s, max. 3/30 s, max.
Image compression method*1: H.264 Image quality: Low(Motion priority)/ Normal/ Fine(Image quality priority) Transmission type: Unicast/Multicast Video bit rate: Constant bit rate: 64 kbps/ 128 kbps/ 256 kbps/ 384 kbps/ 512k bps/ 768 kbps/ 1024 kbps/ 1536 kbps/ 2048 kbps/ 3072 kbps/ 4096 kbps/ 8192 kbps*/ Unlimited *Only for WV-SP105, WV-SP105E Frame rate priority: 1 fps/ 3 fps/ 5 fps/ 7.
Standard accessories Installation Guide (this document).................................................1 pc. Warranty card (NTSC model only).................................................1 pc. CD-ROM*1...................................................................................1 pc. Code label *2................................................................................1 pc. The following parts are used during installation procedures. Power cord plug............................................
Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.
For U.S. and Canada: For Europe and other countries: Panasonic System Communications Company of North America, Unit of Panasonic Corporation of North America Panasonic Corporation www.panasonic.com/business/ For customer support, call 1.800.528.6747 Three Panasonic Way, Secaucus, New Jersey 07094 U.S.A. http://panasonic.net Importer's name and address to follow EU rules: Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15, 22525 Hamburg F.R.Germany Panasonic Canada Inc.
