Operating Instructions Included Installation Instructions Wall Mount Bracket Model No. WV-Q122A The camera in the illustration is separately sold. Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number is abbreviated in some descriptions in this manual.
CONTENTS Preface.......................................................................................................................................................................................3 Precautions................................................................................................................................................................................3 Precautions for installation..............................................................................................
Preface This mount bracket is used for installing the color CCTV camera and network camera on a wall. Refer to the catalog or operating instructions of the camera for further information about the compatible models. Precautions Refer installation work to the dealer. Installation work requires technique and experiences. Failure to observe this may cause fire, electric shock, injury, or damage to the product. Be sure to consult the dealer.
Precautions for installation Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation. The installation should comply with local electrical code. Before start the installation/connection, check and prepare the required devices and cables. Before starting the connection, turn the power of the devices including the camera and the PC off. Refer installation work to the dealer.
Major operating controls 220 mm {8-21/32 inches} Hexagonal screw hole for mounting camera (4 points) Camera mounting part Wire hook section Cable access hole (front) m 120 m hes} inc 2 3 / 3 {4-2 269 mm {10-19 /32 inc hes} Plate Cable access hole (rear) 5
Installations/Connections Be sure to read "Precautions" and "Precautions for installation" before installation. Read the operating instructions for the camera to be installed as well. The Operating Instructions mainly describe for installing a network camera. The basic flow of the installation operation is the same as the one for the color CCTV camera. The flow of how to install the wall mount bracket is described as follows.
Step 3 Remove the attachment pipe from the upper base by loosening 4 screws. Attachment pipe Go to "■ When laying cables through the cable access hole (front)" (☞ 8 page) or "■ When laying cables after drilling a hole through the wall" (☞ 10 page).
[2] Attaching the mount bracket The installation of the wall mount bracket is roughly divided into 2 methods. Refer to the applicable description. ■W hen laying cables through the cable access hole (front) (☞ 8 page) ■W hen laying cables after drilling a hole through the wall (☞ 10 page) ■ When laying cables through the cable access hole (front) Step 1 Step 2 Decide the mounting position and drill a hole in the wall. Procure 4 pieces of M8 screws and anchors to secure the this bracket on the wall.
For the case of the camera with M6 screws being used: Use the screws supplied with the bracket and a hexagonal wrench "for M6". (Recommended tightening torque (for common use in M5 and M6): 2.45 N.m {1.81 lbf·ft}) Step 7 Connect the cables to the camera. Connect the cables from the housing base with the cables on the wall. After cable connection, seal the connecting portion with waterproof tape (locally procured). Step 4 Seal the slit of the cable cap for the prevention of water leakage.
■ When laying cables after drilling a hole through the wall Step 2 Step 1 Decide the mounting position, and drill a hole for a screw or an anchor and a hole for cable installation in the wall. Procure 4 pieces of M8 screws and anchors to secure the this bracket on the wall. All screws and anchors shall be stainless steel. The hole diameter shall be decided in accordance with the screws and anchors to be used.
Step 5 Step 6 Lay the cables from the housing base via this blacket into the slit cable cap. Secure the housing base to the wall mount bracket. Attach the housing base to the mount bracket using the 4 screws*. The "REAR" mark of the housing base shall be directed to the wire hook section. * Refer to the Operating Instructions of the camera for the screws and the wrenches to be used, which depends on models.
[3] Mounting of the camera body on the mount bracket Step 1 Step 2 For the case of color CCTV camera, peel off the seal on the top of the camera, and specify the communication method and unit address using the DIP switches. Refer to the Operating Instructions of the color CCTV camera for how to set the DIP switch. Put the seal back after specifying them. Communication method: specifying with SW2 Unit address: specifying with SW1 Align the flat spring with the START position.
Step 4 Step 5 When attaching the camera to the housing base, the positioning pin shall be on the "REAR" side. Make sure that the camera is securely attached to the mount bracket by turning the bracket counterclockwise (seen from below). Tighten them firmly with the 3 screws* that have been removed in Step 1. * Special screw (fixing screw): These screws are hexagon screws. Use a hexagon wrench.
Specifications Ambient operating temperature: Dimensions: Mass: Finish: –50 °C to +55 °C {–58 °F to 131 °F} 120 mm (W) x 220 mm (H) x 269 mm (D) {4-23/32 inches (W) x 8-21/32 inches (H) x 10-19/32 inches (D)} Approx. 2 kg {4.42 lbs} Aluminum die cast (coating color: fine silver (901)) Weight and dimensions indicated are approximate. Specifications are subject to change without notice. Standard accessories Operating Instructions (this document)...............................................
For U.S. and Canada: For Europe and other countries: Panasonic System Communications Company of North America, Unit of Panasonic Corporation of North America Panasonic Corporation www.panasonic.com/business/ For customer support, call 1.800.528.6747 Three Panasonic Way, Secaucus, New Jersey 07094 U.S.A. Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 www.panasonic.ca © Panasonic System Networks Co., Ltd. 2013 http://panasonic.
