WV-CW484F WV-CW480S WV-CW484F is shown above. Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. No model number suffix is shown in this manual. êìëëäàâ ITALIANO ESPAÑOL FRANÇAIS Model Nos.
ENGLISH VERSION WARNING: • This apparatus must be earthed. • Apparatus shall be connected to a mains socket outlet with a protective earthing connection. • The mains plug or an appliance coupler shall remain readily operable. • All work related to the installation of this product should be made by qualified service personnel or system installers. • The connections should comply with local electrical code.
CONTENTS We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standards or other normative documents following the provisions of Directives EEC/73/23 and EEC/89/336. Vi deklarerar härmed värt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i överensstämmelse med standarddokument, eller andra normativa dokument som framställs i EEC-direktiv nr. 73/23 och 89/336.
Important Safety Instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Clean only with dry cloth. 6) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 7) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 8) Do not defeat the safety purpose of the polarized or grounding-type plug.
Limitation of Liability THIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THE THIRD PARTY'S RIGHT. THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).
Preface Panasonic's WV-CW484F and WV-CW480S cameras introduce high picture quality by use of Super-Dynamic 1/3 inch CCD and digital signal processing LSIs. • WV-CW484F: This is a model with 2x variable focal lens. Mounting bracket and ceiling mount bracket are optional. (Power source: 12 V DC/24 V AC) • WV-CW480S: This is a model with 2x variable focal lens. Mounting bracket is provided, but ceiling mount bracket is optional.
Precautions This apparatus has no power switch. Power is supplied from an external 12 V DC/ 24 V AC (WV-CW484F) or 220 V to 240 V AC (WV-CW480S) power-supply device. Refer to service personnel for how to turn on/off the power. To keep on using with stable performance • Parts of this product may deteriorate and it may shorten lifetime of this product when using in locations subject to high temperatures and high humidity. Do not expose the product to direct heat such from a heater.
About the dehumidifying device • The camera has dehumidifying device to keep the inside at low moisture level, preventing condensation and quickly dissipating dew if produced. • Dew may be produced depending on the conditions of temperature, humidity, winds, and rain, and it may take time to dehumidify. • Never seal the surfaces of the dehumidifying device. Dehumidifying device Turn the circuit breaker off which supplies the camera with the power when abnormal conditions are encountered.
Consumable parts Contact your dealer for replacement of the following part when the time comes: Cooling fan needs replacement after around 30 000 hours of operation. Do not operate the camera beyond the specified temperature, humidity or power source ratings. Use the camera at temperatures within –10 °C to +50 °C, and humidity below 90 %. The input power source is 12 V DC/24 V AC (WV-CW484F) or 220 V to 240 V AC (WVCW480S). What to do if OVER HEAT appears on the display.
Major Operating Controls and Their Functions q w e r t y u i o !0 !1 !2 !3 !4 10 !55 !6 !7 !8 !9
q Power cable (12 V DC or 24 V AC) Cautions: • Supplies 24 V AC or 12 V DC from an external power source. (WV-CW484F) • Supplies 220 V to 240 V AC from an external power source. (WV-CW480S) w Video output cable with BNC connector Connects wih the video connector. e Enclosure r Focus lever Fixes the focus position after adjusting. t Zoom lever Fixes the zoom position after adjusting. y Tilting lock screw Fixes the tilting position after adjusting.
Installations • The following installation should be made by qualified service personnel or system installers. • Mounting Bracket (WV-Q114) is optional for WV-CW484F. Use the screws provided to the Mounting Bracket. • Mounting Bracket is provided to WV-CW480S. Use the screws (M4 x 8, 4 pcs.) provided to this product. Important: • Prepare four fixing screws to be used to mount the provided camera attachment according to the material of the area where the attachment is to be installed.
■ Installations (WV-CW484F) ● Using a Junction Box Secure the provided camera attachment to the two gang junction box built in a wall or ceiling. 46 mm Junction box 83.5 mm Camera attachment (provided) Screws for the camera attachment (Locally procured) ● Using Mounting Bracket WV-Q114 (Option) • Secure the optional camera mounting bracket to wall or ceiling, and fix the provided camera attachment to the mounting bracket with the screws for the mounting bracket.
Mounting bracket TOP TOP Camera attachment (provided) ■ Installations (WV-CW480S) ● Using Provided Mounting Bracket • Secure the provided camera mounting bracket to wall or ceiling, and fix the provided camera attachment to the mounting bracket with the screws for to the mounting bracket. (Refer to the following figures.) Verify the camera attachment and mounting bracket are mounted firmly after screwing them.
Camera attachment (provided) ■ How to mount the camera (WV-CW484F, WV-CW480S) 1. Connect the power cable and the BNC plug of the video output cable. (Refer to p. 22 Connections.) 2. Secure the camera with four attachment fixing screws.
3. Hook the rear screws on the screw holes of camera attachment, and turn the camera unit clockwise to fix the camera unit and camera attachment. Protrusion Screw hole of camera attachment Rear screw 4. Remove the enclosure from the main body by loosening the three fixing screws. The enclosure is fixed with tamperproof screws. Loosen the three fixing screws by using the provided bit for tamperproof screw. Note: Perform the same procedure when replacing with the optional dome cover WV-CW4S. 5.
6. Secure the camera unit to the bracket with the camera lock screw. Camera fixing screw 7. Adjust the camera. (Refer to p. 20.) 8. Attach the enclosure to the camera. Firmly tighten the three tamper-proof screws. (Recommended tightening torque: 0.78 N·m) Notes: • Defocus may be caused by the reinstalled enclosure. When using a system controller, adjust the back-focus on the setup menu after attaching the enclosure.
■ Waterproof Process • When routing cables sideway using Mounting Bracket or installing the camera under eaves, apply waterproof process to the cable and relevant portions. • The cables are not waterproofed. Provide water sealing for the tube ends and the portions between cable cores as well as connecting portions. • The use of vinyl tape or other tapes instead of the butyl tape may cause water absorption from a gap and finally condensation and water leakage.
Notes: • Surely attach a pipe fitting to the bracket to avoid exposing the cables. Otherwise, cable deterioration resulting from cable exposure may cause a short circuit. • Run the conduit downward or pull the conduit out of the side of the bracket. When pulling the conduit out of the side of the bracket, run the conduit downward once, and upward. Downward • For wall installation, face the drain slit downward and do not block the hole.
Image Adjustment You can manually adjust the pan/tilt/azimuth angles, focus, and zoom while observing the connected monitor. 1. Connect an LCD monitor to the monitor output jack. 2. Pan/tilt/azimuth adjustment • Loosen the three screws locking the pan and tilt tables. • Pan and tilt the table to aim the camera at what you need to watch. • Turn the azimuth adjuster to obtain a level image. • Tighten the three screws after adjusting.
5. Aim the camera at the targeting objects and if applicable adjust the zoom angle. 6. Press the [ABF1] button. → The LED indicator will light up, and a bar graph with "I" cursor and INDICATOR (4-digit number) will be overlaid on the camera picture. → Back-focus will be automatically adjusted. NEAR FAR .........|.......... INDICATOR 255 FOCUSING 7. If needed, perform manual adjustment using the [LEFT] or [RIGHT] buttons to obtain the best focus on the targeted object while observing the picture.
Connections Caution: ONLY CONNECT THIS TO 24 V AC or 12 V DC CLASS 2 POWER SUPPLY. (WVCW484F) Brown (Live) Blue (Neutral) Power cable (WV-CW484F: Approx. 26 cm, WV-CW480S: Approx. 183 cm) Green/Yellow (GND) • To 24 V AC or 12 V DC power supply (WV-CW484F) • To 220 V to 240 V AC power supply (WV-CW480S) To GND * When using 12 V DC power supply, the optional heater unit is unavailable. BNC connector BNC connector Video output cable (WV-CW484F: Approx. 22 cm, WV-CW480S: Approx.
Cautions: • Be sure to connect the GND (grounding) lead of the camera and grounding terminal of the power supply when using a 24 V AC (WV-CW484F) or 220 V to 240 V AC (WV-CW480S) power source. • Shrinking the cable-entry seal is a onetime procedure. Do not shrink the cable entry seal until it has been ascertained that unit is functioning. ONLY CONNECT THIS TO 24 V AC or 12 V DC CLASS 2 POWER SUPPLY.
■ Optional Heater Unit WV-CW4H ● Introduction Installing this heater unit enables the camera to operate in a low-temperature environment below –30 °C. The heater turns on automatically when the temperature inside the camera drops below +10 °C and turns off when the temperature rises. A small fan inside the unit will minimize condensation on the surface of the enclosure caused by changes in ambient temperature unless temperatures change too rapidly.
About Setup Menus Before operation, setup of this camera is required. On the setup menu, you can check current settings and perform settings to meet requirements. The following is an example of setup procedure when LANGUAGE is set to ENGLISH. Settings items of the camera setup page Setup item CAMERA Description Reference pages Configure the settings relating to camera operations CAMERA ID The camera title can be edited and displayed on the screen. 29 ALC Configure the light control method.
Setup item Description Reference pages SPECIAL CHROMA GAIN Adjust the chroma level (colour density). 40 AP GAIN Adjust the aperture level. 41 PEDESTAL Adjust the pedestal level (brightness). 41 PIX OFF Correct image defects such as scratches. 41 CAMERA RESET Reset the settings of setup menu to the default settings. 42 Check the serial number of this camera. 42 Select the language to display the setup menu. 29 SER.NO.
■ Basic operation The following are descriptions of how to configure each setup item using the operation buttons (refer to p. 10) on the camera. Setup using an optional system controller is also available. Notes: • The illustrations are the examples to be displayed on a video monitor. 1. Hold down the [SET] button for around 2 seconds. → The top page will be displayed. MODEL WV-CW480 SERIES CAMERA BACK-FOCUS SPECIAL LANGUAGE 2. Move the cursor onto "END" by press the [UP] or [DOWN] button. END 3.
6. To exit from the SETUP menu and display images from the camera, move the cursor onto "END" and press the [SET] button. Notes: • To prevent erroneous operations, the "DISABLE" indication will always be displayed when the top page is displayed from the camera. To operate the SETUP menu, switch the "DISABLE" indication to the "ENABLE" indication first. • The cursor position will be displayed highlighted.
Setting Procedures First, select a language for menu display and camera ID display. Language Setup (LANGUAGE SETUP) **LANGUAGE SETUP** LANGUAGE ENGLISH 1. Select LANGUAGE on the top menu and press the [SET] button. → The LANGUAGE SETUP menu opens. 2. Select a language. The default setting is SET RET TOP END English. Available languages: ENGLISH, FRANÇAIS, ESPAÑOL, DEUTSCH, ITALIANO, êìëëäàâ, CHINESE, JAPANESE 3. Select SET on the menu and press the [SET] button. 1.
• To erase all characters of the camera ID, select RESET and press the [SET] button. Note: For Chinese language, up to 8 characters can be entered. 4. To specify the ID display position: 1. Select POSI and press the [SET] button. → The entered camera ID will be highlighted on the screen. 2. Move it into the appropriate position and press the [SET] button. → The position is determined and the screen will return to the CAMERA ID menu.
2-2. ALC Mode with SUPER-D3 OFF **ALC CONT** BACK LIGHT COMP SUPER-D3 MASK SET OFF ↵ 1. Move the cursor to ALC on the CAMERA SETUP menu and select OFF for SUPER-D3 on the ALC CONT menu. → MASK SET↓ appears on the ALC CONT menu. LEVEL 2. Select MASK SET and press the [SET] button. → The 48 mask areas appear overlaid on the camera picture with the blinking cursor in the upper left corner. ..I...128 + RET TOP END Blinking 3.
Notes: • Only OFF is available when SUPER-D3 is set to ON. • When a faster speed is selected for the electronic shutter, the picture will generally become darker, and sometimes a smear (vertical stripes caused by bright objects) may appear. 4. Gain Control Setting (AGC) Select an automatic gain control mode. This setting raises the gain and brightens the image under low light conditions. The default setting is ON (HIGH). Available modes: ON (HIGH / high), ON (MID / medium), ON (LOW / low), OFF 5.
6. Synchronization Setting (SYNC) 1. Select a sync mode. VD2: Multiplexed vertical drive, highest priority LL: Line-Lock, follows the phase of supplied AC power, 2nd priority INT: Internal sync, lowest priority Notes: • Selection is not available when VD2 is added to the camera. Selection from LL is available when the respective sync is added. • When LL is selected, phase adjustment is required. 2. Line-Lock Vertical Phase Adjustment (V PHASE) • Select LL and press the [SET] button.
AWC Setting 1. Select AWC and press the [LEFT] button. → AWC will change to AWC → PUSH SW. 2. Press the [SET] button. → PUSH SW will be highlighted while the AWC setting is performed. Note: If the white balance is not set, PUSH SW is being highlighted. 3 . Press the [RIGHT] button. Manual Fine Adjustment Perform fine adjustment as necessary. 1. Select WHITE BAL and press the [SET] button. → Fine adjustment menu of ATW or AWC will open. 2. Adjust finely R (Red) and B (Blue) gain by moving the "I" cursor.
5. Select ON or OFF for ALARM under DISPLAY MODE. ON: Outputs an alarm OFF: Does not output an alarm. This is applicable any of the following controllers are used: WV-RM70, WV-CU550 series, WV-CU161, WV-CU360, WV-CU650, WV-CU850, WVCU950 6. Select DISPLAY MODE and press the [SET] button to see the current settings. When a motion is detected, the area will blink. • Press the [SET] button to return to the MODE1 menu. 7.
About MODE2 of Motion Detection • The camera will detect a scene change in the following cases. When the lens is fully sprayed or covered with a cloth, lid, or the like When the camera direction is suddenly changed • The camera will not detect a scene change in the following cases.
→ When AUTO1 or AUTO2 is selected, LEVEL and DURATION TIME appear. 3. Select a threshold LEVEL to switch between the colour and black-and-white mode. The default setting is HIGH. HIGH: Switches the mode at approx. 5 lx illumination. LOW: Switches the mode at approx. 1 lx illumination. **BW MODE** BW AUTO1 LEVEL HIGH DURATION TIME .I.. S L BURST(BW) ON RET TOP END 4. Select a duration time to determine whether to switch the mode. The default setting is 30 seconds.
5. Select →PUSH SW for SCALE and press the [SET] button. → Zone scale adjustment becomes available. 6. Adjust the zone scale using the [LEFT], [RIGHT], [UP], or [DOWN] button. 7. To apply the settings, move the cursor to SET and press the [SET] button. → The screen returns to the ZONE NUMBER selection menu. To delete the settings, select DEL and press the [SET] button. 13. Electronic Zoom (EL-ZOOM) 1. Move the cursor to EL-ZOOM. 2. Select ON or OFF by pressing [LEFT] and [RIGHT] buttons.
• Image stabilization may not function where there is excessive camera movement or when the scene is low light or low contrast objects. 16. LENS Select PANASONIC. 17. Back-focus Setting (BACK-FOCUS SETUP) **BACK-FOCUS SETUP** →PUSH SW ABF MANUAL-ADJ AUTO C/L← → B/W SETUP-SW LOCK OFF ↵ Perform adjustment of the back-focus (flangeback: the gap between the lens and focal plane) remotely on this menu using a system controller.
4. Select a mode for C/L ↔ B/W. The default setting is AUTO. AUTO: Adjusts the back-focus automatically every time the camera switches the mode between colour and black-and-white. AUTO is usable only when OFF, X2 AUTO, or X2 FIX is selected for SENS UP. PRESET: Adjusts the back-focus to the positions for colour mode and black-and-white mode that are preset by performing step 2 (automatic) or step 3 (manual) under the respective light conditions. FIX: Fixes the back-focus after adjustment. 5.
18-2. Aperture Gain Setting (AP GAIN) Move the "I" cursor to adjust the aperture gain level. Lower the level when moire (a kind of noise, optical interference) appears on the screen as part of minute crosshatch pattern, etc. 18-3. Pedestal Level Setting (PEDESTAL) Move the "I" cursor to adjust the pedestal level (black level). 18-4. Pixel Compensation Setting (PIX OFF) Perform settings to compensate a maximum of 16 blemish pixels on the pickup device. 1. Select PIX OFF and press the [SET] button.
18-5. To reset to the default settings (CAMERA RESET) 1. Select CAMERA RESET. → The PUSH SW is highlighted. 2. While holding down the [LEFT] and [RIGHT] buttons, press the [SET] button for 2 seconds or more. → The camera will return to the default settings. Note: PIX OFF setting cannot be initialized. 18-6. The serial number of the camera will be displayed. (SER. NO.
Troubleshooting Before asking for repairs, check the symptoms with the following table. Contact your dealer if a problem cannot be solved even after checking and trying the solution or if the problem is not described below. Symptom No image is displayed. Images are displayed blurry.
Specifications Power source and power consumption: 24 V AC 50 Hz, 4.1 W (Without heater), 11 W (With heater), 12 V DC 50 Hz, 340 mA (Without heater), 470 mA (With heater)* Ambient temperature: –10 °C to +50 °C –30 °C to +50 °C** Ambient humidity: 90 % or less Water resistance: IEC60529 (IP66, Against ingress of water with harmful effects powerful jetting)*** (Camera unit) Dimensions: ø154 mm (W) x 141.2 mm (H) (excluding connectors/terminals) Weight: Camera: 1.
Minimum illumination: Lens mount: Lens Type: Focal length: F number: Focus range: Angle of view: Adjusting angle: When using Clear Dome Cover: 0.08 lx at F1.4 (B/W) 0.6 lx at F1.4 (C/L) When using Smoke Dome Cover (Option): 0.16 lx at F1.4 (B/W) 1.5 lx at F1.4 (C/L) CS-mount 2x variable focal lens f=3.8 mm - 8.0 mm F1.4 - 1.8, close ∞ - 1.2 m Horizontal: 73.6 ° (WIDE) - 35.6 ° (TELE) Vertical: 53.4 ° (WIDE) - 26.
Standard Accessories Operating Instructions (This document) ............................................ 1 pc. The following parts are used during installation procedures. Mounting Bracket (For WV-CW480S) ................................................ 1 pc. Screws for mounting bracket (M4 x 8) (For WV-CW480S) ................. 4 pcs. Camera attachment ........................................................................... 1 pc. Bit for tamperproof screw ................................................
Matsushita Electric Industrial Co., Ltd. Osaka, Japan http://panasonic.net Printed in Japan Gedruckt in Japan Imprimé au Japon Impreso en Japón Stampato in Giappone © 2006 Matsushita Electric Industrial Co., Ltd. All Rights Reserved.
