System Controller Operating Instructions WV-CU550C Model No. ALA RM BUS Y A RESCK ET 1 BA SEQCK FO W SEQ ARD ALT F1 AUX D -1C EC AM F2 1 2 IN +1C C AM 4 STO P 7 ESC 5 8 MO N SLO W F3 2 F4 3 6 RES ET CLO IRIS SE OP EN 9 0 CAM UP ZO TEL OM E SET LEF T FO NEACUS R WID E FAR RIG HT DO WN Sys tem Co ntro ller WV 550 -CU C Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.
CONTENTS IMPORTANT SAFETY INSTRUCTIONS ......................................................................................................................................... 3 PREFACE ....................................................................................................................................................................................... 4 FEATURES ..................................................................................................................................
IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not use near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
PREFACE The WV-CU550C System Controller, when combined with the optional WJ-SX550C Matrix Switcher and WJ-AD550 Extension Unit, allows for flexible control of 128 cameras and 16 monitors. When used in a system with either Receivers (WV-RC100 or WV-RC150) or with Panasonic’s Combination cameras, the WVCU550C can control camera functions such as zoom and focus and can also control accessory equipment such as Pan/Tilt Heads.
PRECAUTIONS • Refer all work related to the installation of this product to qualified service personnel or system installers. • Do not attempt to disassemble the appliance. To prevent electric shock, do not remove screws or covers. There are no user-serviceable parts inside. Contact qualified service personnel for maintenance. • Handle the appliance with care. Do not strike or shake it, as this may damage the appliance. • Do not expose the appliance to water or moisture, nor try to operate it in wet areas.
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ■ Front View q w ALARM BUSY e !8 !9 r F1 ACK RESET BACK FORWARD SEQ SEQ ALT F2 F3 1 2 3 4 5 6 7 8 9 MON 0 CAM t F4 UP IRIS CLOSE OPEN PRESET LEFT @1 @0 RIGHT AF AUX 1 DEC INC –1CAM +1CAM STOP 2 SLOW ESC SET ZOOM TELE FOCUS NEAR WIDE FAR DOWN System Controller WV-CU !7 !6 !5 !4 !3 !2 !1 !0 o i 550C u ■ Rear View DATA 6 #2 901 ON 23 #1 OFF 78 TERM ON CONTROLLER CONTROLLER UNIT NO.
q Alarm Indicator (ALARM) Blinks to indicate that an alarm condition exists. It changes to steady light when the alarm is reset automatically. To turn the indicator off, press the ACK RESET button. w Busy Indicator (BUSY) Lights up when you attempt to control a monitor or a camera that is already used by a higher priority operator, or when the higher priority operator selects the monitor or camera you are currently operating. Operations from the System Controller are disabled until this indicator goes off.
!7 Auxiliary Button (AUX 1,2) These buttons toggle the auxiliary switches in the Receiver on and off. The auxiliary switches can be used, for example, to activate equipment connected to the receiver, such as lamps and buzzers. #4 Mode Selection Switch (MODE) These switches are used to set the mode of the System Controller connected to the Matrix Switcher. Set the switches as shown below. MODE !8 Alternate Button (ALT) This button activates the alternate function of dual-function control buttons.
INSTALLATION The installation described below should be made by qualified service personnel or system installers and should conform to all local codes. ■ Replacing the Side Panels with the optional WV-Q62 Rack Mounting Brackets 1. 2. 3. 4. Remove both the left and right side panels of the System Controller by removing four screws. Remove the Palm-rest located on the front of the System Controller by removing two screws.
SYSTEM INFORMATION Please note that the following functions were added to improve the operation of the combination cameras. ■ Version Information ● WJ-SX550 Series Matrix Switcher The onscreen display indicates the version in “Cold Start” or “Normal Start” during the power up procedure. ■ Additions ● Selection of Pan/Tilt Speed Matrix The Pan/Tilt speed can be changed by selecting a mode in the menu (A1) displayed on the LCD display of the controller. Model 1. Select the desired monitor and camera.
SPECIFICATIONS Power Supply: Power Consumption: Data Input/Output: Switching Functions: Camera Functions: Lens Functions: Housing: Pan/Tilt: Auxiliary Switch: Unit Number: Ambient Operating Temperature: Ambient Operating Humidity: Dimensions: Weight: 120 V, AC 60 Hz Approx.
Panasonic Security and Digital Imaging Company A Division of Matsushita Electric Corporation of America Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094 Regional Offices: Northeast: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303 Southern: 1225 Northbrook Parkway, Suite 1-160, Suwanee, GA 30024 (770) 338-6838 Midwest: 1707 North Randall Road, Elgin, IL 60123 (847) 468-5211 Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840 Panasonic Canada Inc.