Color CCTV Camera Operating Instructions Model No. WV-CS564 Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.
ENGLISH VERSION For U.S.A CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not use near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
CONTENTS PREFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ■ Auto Pan Key Setting (AUTO PAN KEY) . . . 25 FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ■ Local/Remote Setting (LOCAL/REMOTE) ■ Camera Cleaning .................. 5 ■ Preset Data Uploading or Downloading . . . 5 PRECAUTIONS ....................... 5 . 25 ■ Patrol Learn and Patrol Play (PATROL LEARN and PATROL PLAY) . . 26 ■ Cleaning (CLEANING) . . . . . . . . . . . . . . 28 CONSTRUCTION . . . . . .
■ Camera Cleaning Even if this function is used, noise may be produced on the monitor screen, or the preset position may be deviated in the cause of prolonged use. In such cases, set the refresh mode on the special menu. (See page 39.) To use this camera with the WJ-SX550B Matrix Switcher, set the auto cleaning function on each unit side, then clean WV-CS564 one time a day.
5. Never face the camera towards the sun. Whether the camera is in use or not, never aim it at the sun or other extremely bright objects. Otherwise, blooming or smear may be caused. 10. Do not install the camera near the air outlet of an air conditioner. The lens may become cloudy due to condensation if the camera is used under the following conditions. • Rapid temperature fluctuations by switching the air conditioner on and off. • Rapid temperature fluctuations due to frequent door opening and closing.
CONSTRUCTION q w y e u r t i o !0 7 q Not Used y Camera Mounting Base w Not Used u Panning Starting Point e Video Output Connector i Fall Prevention Wire r Data Port o Decoration Cover t Power Cable !0 Dome Cover
SETUP ■ Setup Menu Setup menus are shown in the diagram below. Various kinds of setup are available to have the camera fulfill your requirements. Menus are built in a hierarchical structure from the Setup menu at the top to Manual Mask Area Selection at the bottom. These menus are described in the following pages for reference prior to setup. Switches, keys and the joystick are used for setup operations. Setup Menu PRESET Menu Home Position Selection MAP Menu Self Return Setting Preset No.
The keys (switches) to use for setup are shown in the table below. The joystick on the connected controller may also be used for setup. The table also shows the functions versus the operations of the individual controllers. For details, see the manual for the controller to be used. The switches and controls are abbreviated as SW and CTRL respectively in the table.
■ Setup Menu Description ● Presetting (1) Position (POSITION SET) Aligns the camera position and focal point by panning, tilting, zooming and focusing. See page 17 for the setting. (2) Preset Identification (PRESET ID) Assigns the name for preset IDs (identification of up to 16 alphanumeric characters) and can be switched on or off on the monitor screen. See page 19 for the setting. (3) Light Control (ALC/MANUAL) Selects the ALC or MANUAL mode for adjust the lens iris. See page 20 for the setting.
● Auto Pan Key (AUTO PAN KEY) This setting assigns the SEQ, SORT, AUTO PAN or PATROL (PLAY) mode to the AUTO key on the controller. After setting this, the AUTO key performs as assigned. Note: The AUTO PAN LED on the controller does not light if the mode other than the AUTO PAN mode is assigned. ● Local/Remote (LOCAL/REMOTE) This setting determines whether the camera continues or stops the ongoing auto operation when the controller is turned off.
● Cleaning (CLEANING) This is used for refreshing the electric-mechanical contacts built in the camera. Use this function for maintenance when the camera has been directed to a specific spot or panned over a specific range for a long time. ● Image Hold (IMAGE HOLD) The camera picture remains a still image on the monitor screen or until the camera reaches the preset position. This function is useful for surveillance via a local area network.
Note: The result of field setup of the mask area and level adjustment is fed back (effected) to the lens iris control in ALC mode. (3) Shutter Speed (SHUTTER) You can select a shutter speed of 1/60 (OFF), 1/100, 1/250, 1/500, 1/1 000, 1/2 000, 1/4 000, and 1/10 000 seconds. See page 32 for the setting. (4) Gain Control (AGC) You can set the gain (brightness level portion of an image) to automatic adjustment [Automatic Gain Control ON (LOW, MID, HIGH)] or fixed (Automatic Gain Control OFF).
(6) White Balance (WHITE BAL) You can select one of two modes for white balance adjustment as follows: • Auto-Tracing White Balance (ATW) In this mode, the color temperature is monitored continuously and thereby white balance is set automatically. The color temperature range for the proper white balance is approx.2 600 - 6 000 K. Proper white balance may not be obtained under the following conditions: 1. The color temperature is out of the 2 600 - 6 000 K range. 2.
SETTING PROCEDURES The following setting procedures are described on the assumption that this model is used in combination with the WJ-SX550B Matrix Switcher and WV-CU550B System Controller. In case of using a controller other than the WV-CU550B, refer to the table on page 10. ■ Menu Display D4 menu ● Setup Menu Display Camera Set Up Menu On Exit WV-CU550B 1. Select the camera number you want to set up and a monitor to display the SET UP MENU. 2.
■ Presetting Setup menu ● Preset Menu Display 1. Displaying the preset menu directly (1) Move the cursor to PRESET 1 and move the joystick to the right or left to select the position number to be set. (2) Press the CAM (SET) key. The preset setting menu appears on the monitor screen. 2. Displaying the preset menu from the PRESET NUMBER SET menu (1) Move the cursor to MAP and press the CAM (SET) key. The PRESET NUMBER SET menu appears on the monitor screen.
3. Pan Offset If the camera is replaced with a new one, the pan offset function is used to adjust its positions to be the same as before except patrol setting. The controller can be downloaded or uploaded the preset position data. Caution: The preset data for other camera models (WV-CS650 for example) is incompatible with WV-CS564's. WV-CS564's preset data will be destroyed if you upload the conventional data. If this happened, reset the WV-CS564 to the default settings.
● Preset Identification Setting (PRESET ID) Preset setting menu 1. Move the cursor to PRESET ID on the preset setting menu and select ON or OFF by moving the joystick to the right or left. The factory default setting is OFF. ON: Preset ID appears on the monitor screen. OFF: Preset ID does not appear. PRESET NO. 1* POSITION SET PRESET ID ALC/MANUAL DWELL TIME SCENE FILE PRESET SPEED RET 2. Press the CAM (SET) key to display the preset ID setting menu.
To Set a Display Position for a Preset ID (1) Move the cursor to POSI and press the CAM (SET) key. The display position set menu appears. (2) Using the joystick, move the ID to the desired position on the monitor screen, and press the MON (ESC) key. The display position is set and the monitor screen returns to the preset ID setting menu. PRESET NO. 1* 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ ().,'":;&#!?= +-*/%$ SPACE COPY POSI RET RESET DOOR............
● Dwell Time (DWELL TIME) Preset setting menu • Move the cursor to DWELL TIME and set a dwell time by moving the joystick to the right or left. The factory default setting is 10S. Dwell time changes as follows: 2S 3S 5S 10S 30S 1MIN 2MIN 3MIN 4MIN S stands for second(s), and MIN stands for minute(s). PRESET NO. 1* POSITION SET PRESET ID ALC/MANUAL DWELL TIME SCENE FILE PRESET SPEED RET ON ALC 10S OFF ••••••••| L H DEL Preset setting menu ● Scene File Setting (SCENE FILE) 1.
■ Deleting Preset Positions Setup menu 1. Move the cursor to PRESET 1* and select the position number to be deleted by using the joystick. 2. Press the CAM (SET) key to display the preset setting menu. ** SET UP MENU ** PRESET 1* MAP HOME POSITION OFF OFF SELF RETURN OFF AUTO MODE AUTO PAN KEY AUTO PAN LOCAL/REMOTE LOCAL PATROL STOP CLEANING OFF CAMERA RS485 SET UP Preset setting menu PRESET NO. 1* POSITION SET PRESET ID ALC/MANUAL DWELL TIME SCENE FILE PRESET SPEED RET 3.
■ Auto Mode Selection (AUTO MODE) 1. To set auto mode Move the cursor to AUTO MODE and select a mode by moving the joystick to the right or left. The factory default setting is OFF. Modes change as follows: OFF SEQ SORT AUTO PAN Setup menu ** SET UP MENU ** PRESET 1 MAP HOME POSITION OFF OFF SELF RETURN OFF AUTO MODE AUTO PAN KEY AUTO PAN LOCAL/REMOTE LOCAL PATROL STOP CLEANING OFF CAMERA RS485 SET UP PATROL AUTO PAN setting menu ** AUTO PAN ** OFF: No automatic operation.
5. To set pan limit ON/OFF Endpoint Move the cursor to PAN LIMIT and select ON or OFF by movCamera ing the joystick to the right or left. Start-end range of The factory default setting is OFF. ON: Manual pan is limited from the starting point to the end- auto pan point specified by position setting. Set ENDLESS to OFF before PAN LIMIT is set to ON. Starting point OFF: Manual pan is not limited.
■ Auto Pan Key Setting (AUTO PAN KEY) Setup menu This is used for assigning one of the following auto functions to the AUTO key on the controller. Pressing the AUTO key activates the assigned function after this setting. • Move the cursor to AUTO PAN KEY and select an auto function by moving the joystick to the right or left. The factory default setting is AUTO PAN.
■ Patrol Learn and Patrol Play (PATROL) A routine of manual operations can be stored for 30 seconds at the maximum and reproduced repetitively. 1. Set the following parameters for the patrol learn starting position. These parameters are stored when the patrol learn mode starts. • PAN/TILT/ZOOM/FOCUS • IRIS • SHUTTER • AGC • WHITE BALANCE • IMAGE HOLD • CAMERA ID • PAN LIMIT • CLEANING After starting the patrol learn, the following manual operations are stored.
Patrol Learn with a Controller not Having the PATROL Key 1. Select the patrol learn in the setup menu, and then close it. Starting points are stored and “LEARNING” appears on the monitor screen. 2. Operate the patrol learn manually. 3. Open the SET UP menu to stop learning. Notes: • It is recommended that you set PAN LIMIT to ON for the patrol learn. Otherwise PAN LIMIT is invalid for playback.
■ Cleaning (CLEANING) Built-in electric mechanical contacts are refreshed at regular intervals (approx. 7 days) if CLEANING is set to ON. A dry contract affects adversely picture quality and motors operation. 1. Move the cursor to CLEANING and select ON or OFF by moving the joystick to the right or left. The factory default setting is OFF.
3. After editing the camera identification characters, follow the steps below to set the position of the CAMERA ID on the monitor screen. 3-1 Move the cursor to POSI, and press the CAM (SET) key to display the ID position menu. 3-2 Use the joystick to decide the position of the CAMERA ID on the monitor screen. Press the MON (ESC) key to fix the position, and return to the character editing menu.
● Light Control Setting (ALC/MANUAL) 1. Display SET UP on the monitor screen. If necessary, refer to Setup Menu Display on page 16 for details on displaying the SET UP on the monitor screen. 2. Move the cursor to ALC/MANUAL and select ALC or MANUAL by using the joystick. The factory default setting is ALC. When you select ALC, set backlight compensation.
(2) ALC Mode with BLC OFF 1. Move the cursor to the BLC and select OFF. (When you select MANUAL, BLC is not available.) The MASK SET appears on the menu. 2. Move the cursor to MASK SET and press the CAM (SET) key. The 48 mask areas appear on the monitor screen. The cursor is blinking in the top left corner of the screen. 3. To mask an area where backlight is bright, move the cursor to that area and press the CAM (SET) key. The mask turns to white. Repeat this procedure to mask the desired area. 4.
● Shutter Speed Setting (SHUTTER) 1. Display SET UP on the monitor screen. If necessary, refer to Setup Menu Display on page 16 for details on displaying the SET UP menu on the monitor screen. 2. Move the cursor to SHUTTER and select the electronic shutter speed by using the joystick. The factory default setting is OFF.
● Synchronization (SYNC) 1. Display SET UP on the monitor screen. If necessary, refer to Setup Menu Display on page 16 for details on displaying the SET UP menu on the monitor screen. 2. Move the cursor to SYNC and select line-lock (LL) or internal (INT) by using the joystick. The factory default setting is INT. Important Notices: 1. The priority of SYNC modes is as follows: 1. Multiplexed vertical drive (VD2) (highest priority) 2. Line-lock (LL) 3. Internal sync (INT) (lowest priority) 2.
7. Use the joystick to match the vertical phases for both video output signals as closely as possible. (COARSE adjustment can be incremented in steps of 22.5 degrees (16 steps) with the joystick.) Note: After the 16 steps, the adjustment returns to the first step. ** SYNC ** V PHASE COARSE 1(1--16) FINE - 1 (1 - - - 16): 0 degrees 2 (1 - - - 16): 22.5 degrees + RET 16 (1 - - - 16): 337.5 degrees 8. Move the cursor to FINE by using the joystick. 9.
(2) Automatic White Balance Control Mode (AWC) 1. Display SET UP on the monitor screen. (Refer to Setup Menu Display on page 16 for details on displaying the SET UP menu on the monitor screen.) Camera setting menu ** SET UP ** CAMERA ID ON ALC/MANUAL ALC SHUTTER OFF AGC ON(MID) SYNC INT WHITE BAL AWC AF MODE MANUAL S EL-ZOOM ON IMAGE HOLD OFF 2. Move the cursor to WHITE BAL and select AWC → PUSH SW by using the joystick. 3. Press the CAM (SET) key to start the white balance setup.
● Auto Focus Setting (AF MODE) 1. Move the cursor to AF MODE, and select the following mode by moving the joystick to the right or left. The factory default setting is MANUAL S. S, M and L stand for Small, Middle and Large areas in the center of a scene that are used for sensing sharpness in auto-focusing. AUTO S MANUAL L AUTO M AUTO L MANUAL M MANUAL S MANUAL S, M, L: Brings the camera into focus when the AF key on the controller is pressed.
● Electronic Zoom (EL-ZOOM) The electronic zoom magnifies a scene 2-fold. With a 18-fold optical zoom lens, the camera is capable of 36-fold zoom. 1. Move the cursor to EL-ZOOM and select ON or OFF by moving the joystick to the right or left, and then press the CAM (SET) key. The factory default setting is ON. ON: Two (2) - fold electronic zoom is available with the ZOOM switch on the controller. OFF: The electronic zoom function is not used.
● Special Menu (SPECIAL) This menu lets you adjust and set up the picture quality to meet your requirements. • Display SET UP on the monitor screen. (Refer to Setup Menu Display on page 16 for details on displaying the SET UP on the monitor screen.) • Move the cursor to SPECIAL and press the F2 button of the WVCU550B. The special menu appears on the monitor screen. (For the WV-RM70, keep pressing the Right and Left switches simultaneously for 2 seconds or more.) (1) Chroma Level Setting (CHROMA GAIN) 1.
(5) To Restore the Camera Default Position (REFRESH) Move the cursor to REFRESH by using the joystick and press the F2 button of the WV-CU550B. (For the WV-RM70, WV-CU360 or WV-CU161, keep pressing the Right and Left switches simultaneously for 2 seconds or more.) (6) Camera Resetting (CAMERA RESET) Move the cursor to CAMERA RESET by using the joystick and press the F3 button of the WV-CU550B. The camera is reset to the factory preset parameters.
How to Reset to the Factory Preset Parameters Any of the above settings plus the ALC/MANUAL level control and phase adjustments can be reset to the factory preset parameters by placing the cursor over the desired mode and then press the F2 button of the WV-CU550B. (For the WV-RM70, keep pressing the Right and Left switches simultaneously for 2 seconds or more.
X ON/X OFF (X ON/X OFF) Specifies whether to apply flow control or not (NOT USE, USE). The factory setting is NOT USE. Wait Time (WAIT TIME) Specifies the time to wait until retrying after confirming that no data is received from the controller. (OFF: no retry, 100, 200, 400, 1 000 ms). The factory setting is OFF. Delay Time (DELAY TIME) Specifies the time to transmit the acknowledge request when communicating on a 2-line connection. [----,100 ms] Default: ---- (no set).
INSTALLATION Precautions • The following steps of installation and connection should be taken by qualified service personnel or system installers and should conform to all local codes. • Make sure to switch the camera off before installation and connection. • Do not install the camera near the air outlet of an air conditioner. 1. Disassembling the Camera Camera mounting base Camera mounting base Fixing screw (1) Loosen the fixing screw to separate the camera mounting base and the camera.
Unit Number Switch 1, an 8-bit DIP switch, specifies unit number or returns to the factory default settings for Panasonic’s protocol. When the switch position corresponding to the unit number 1-96* is selected, setting should be made on the RS485 SET UP menu (see page 40).
Switch position Unit number 2 3 4 5 6 7 8 69 ON 1 2 3 4 5 6 7 8 70 2 3 4 5 6 7 8 71 2 3 4 5 6 7 8 72 2 3 4 5 6 7 8 73 2 3 4 5 6 7 8 74 2 3 4 5 6 7 8 75 45 7 8 1 1 1 1 1 1 2 3 4 5 6 7 8 76 1 2 3 4 5 6 7 8 79 3 4 5 6 7 8 77 1 1 2 3 4 5 6 7 8 87 1 2 3 4 5 6 7 8 88 2 3 4 5 6 7 8 89 2 3 4 5 6 7 8 90 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3
RS485 Setting The 4-bit DIP switch in used for RS485 termination. ON 1 BP 1 Switch position Note: Remove sharp edges to protect the cables. SW 2 2 3 4 Function ON Termination ON OFF Termination OFF * BP 2 BP 3 BP 4 Function Switch ON ON ON Half duplex (2 line) position OFF OFF OFF Full duplex (4 line) * b. Top Cable Exit Prepare a hole in the ceiling board to run the cables. Notes: • Defaults are marked with *. • BP stands for Bit Position.
3. Hook the fall prevention wire on the camera mounting base. 5. Tighten the fixing screw M3 (provided). Notes: (1) Tighten the camera fixing screw with a screwdriver. (2) Follow the instructions given here to ensure that the camera and camera mounting base are installed safely. (3) When removing the camera from the camera mounting base, loosen and press up the camera fixing screw (M3) by using a screwdriver. Be sure to match the wire with the fall prevention wire fixing angle as shown below.
CONNECTIONS Precautions • The following connections should be made by qualified service personnel or system installers in accordance with all local codes. • See the reverse side of the cover page for mains lead connection. 24 V AC 24 V AC cable RS485 cable Data port Coaxial cable Video output Not used BNC plug BNC plug To VIDEO IN (CAMERA IN) Not used ✻ The coaxial cable length (RG-59/U, BELDEN 9259) for the connection is up to 900 meters (3 000 ft.
• RS485 Connection Brown GND Red Data transmission Orange Yellow Data reception Green Note: Use the cable that is described below for RS485 site communication. • Shielded, twisted pair cable • Low impedance • Wire gauge size is thicker than AWG #22 (0.33 mm2).
SYSTEM CONNECTIONS Color CCTV camera Max.
PREVENTION OF BLOOMING AND SMEAR When the camera is aimed at a bright light, such as a spotlight, or a surface that reflects bright light, smear or blooming may appear. Therefore, the camera should be operated carefully in the vicinity of extremely bright objects to avoid smear or blooming.
Auto focus Auto mode Auto pan key Camera ID PATROL Cleaning MANUAL/AUTO OFF/SEQ/SORT/AUTO PAN/PATROL SEQ/SORT/AUTO PAN/PATROL PLAY preset ID, camera ID: up to 16 characters LEARN/PLAY/STOP, up to 30 seconds ON/OFF Panning range Panning angle setting Panning mode 360° endless possible (in auto-pan mode) manual/sequential position/sort position/auto pan manual : approx. 0.1°/s - 120°/s 8-steps/64-steps sequence position : maximum approx.
APPENDIX Shortcuts Shortcut operations are available to controllers having the CAM FUNCTION key. Pressing numeric key(s) for one digit up to three digits then CAM FUNCTION key implements the respective functions as follows. The CAM FUNCTION key is abbreviated to [CAM FUNC] here.
Panasonic Security and Digital Imaging Company A Division of Matsushita Electric Corporation of America Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094 Regional Offices: Northeast: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303 Southern: 1225 Northbrook Parkway, Suite 1-160, Suwanee, GA 30024 (770) 338-6838 Midwest: 1707 North Randall Road, Elgin, IL 60123 (847) 468-5211 Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840 2001 © Matsushita Communication Industrial Co.
