Installation Guide Color CCTV Camera Model Nos. WV-CP500 WV-CP504 This illustration represents WV-CP500. Lens: Option Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. No model number suffix is shown in this manual.
WARNING: • This apparatus must be earthed. • Apparatus shall be connected to a mains socket outlet with a protective earthing connection. • The mains plug or an appliance coupler shall remain readily operable. • To prevent fire or electric shock hazard, do not expose this apparatus to rain or moisture. • The apparatus should not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, should be placed on the apparatus.
Important safety instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Limitation of liability THIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THE THIRD PARTY'S RIGHT. THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS.
Preface This product is a 1/3-inch type {1/3"} CCD color CCTV camera. Connection of this product to a video monitor allows users to use this product as a monitoring camera. • WV-CP500: 120 V AC power supply • WV-CP504: 24 V AC, 12 V DC power supply Introduction of SUPER-D5 (super dynamic function) Integration of SUPER-D5 into the CCD and signal processing circuit has achieved approximately 128 times higher dynamic range as compared with conventional camera.
About the user manuals The operating instructions of the camera consist of 2 sets: this book and operating instructions (PDF). This book explains how to install the camera. Refer to the "Operating Instructions (PDF)" on the provided CD-ROM for descriptions of how to perform the unit settings. Adobe® Reader® is required to read PDF. When the Adobe® Reader® is not installed on the PC, download the latest Adobe® Reader® from the Adobe web site and install it.
Contents Important safety instructions....................................................................................................... Limitation of liability..................................................................................................................... Disclaimer of warranty................................................................................................................. Preface......................................................................................
Precautions This product has no power switch. Power is supplied from an external 12 V DC/ 24 V AC (WV-CP504) or 120 V AC (WVCP500) power-supply device. Refer to service personnel for how to turn on/off the power. Use this product for indoor use only. Do not expose this product to direct sunlight for hours and do not install the product near a heater or an air conditioner. Otherwise, it may cause deformation, discoloration and malfunction. Keep this product away from water.
Major operating controls and their functions Side view (WV-CP500) ALC lens connector Side cover Tripod mount base Inside the side cover (Slide the cover leftward to the lock position.
Rear view (WV-CP500) External terminal ALARM OUT GND ALARM IN Power indicator Video output connector POWER VIDEO OUT 120V ~ 60Hz Power connector Rear view (WV-CP504) External terminal ALARM OUT VIDEO OUT GND POWER ALARM IN Power indicator (UP) NEAR 24V ~ IN 1-L 2-N (LEFT) GND BF/MENU (SET) FAR (RIGHT) (DOWN) 12V IN NC AC/DC power terminal Video output connector 10 Operation buttons* * The following names are assigned to each button in this book: : Up button (UP) : Down button (DOWN) :
Side cover (only for WV-CP500) When the operation buttons are used, the side cover is slide leftward to the lock position. Power indicator This indicator lights up when the power is on. ALC lens connector The ALC connector is connected to this ALC lens connector. Power connector (only for WV-CP500) The included power cord is connected to this power connector. Tripod mount base This socket is used to mount the camera mount bracket (option).
Precautions for installation This camera is designed to be used indoors. This camera is not operable outdoors. Do not operate this product beyond the specified temperature, humidity or power source ratings. Use this product at temperatures within –10 °C to +50 °C {14 °F to 122 °F}, and humidity below 90 %.The input power source is 12 V DC/24 V AC (WV-CP504) or 120 V AC (WV-CP500). Installing place Contact your dealer for assistance if you are unsure of an appropriate place in your particular environment.
Power cord (only for WV-CP500) Connect the power cord securely. Run the power cord so that no load is applied to the cord when panning or tilting the camera. (Failure to observe this may disconnect the power cord, and accordingly no image is displayed.
Installation and connection Cautions: • ONLY CONNECT WV-CP504 TO 24 V AC OR 12 V DC CLASS 2 POWER SUPPLY. • Be sure to connect the grounding lead to the GND terminal. z Rotate the lens (option) clockwise slowly to mount the lens. Protrusion from mount: ø20 mm {25/32”} or less Important: • For use of C-mount lens, use the C-mount adaptor (option). • For prevention of damage to the camera body, use a lens with protrusion of 5.5 mm {7/32"} or less from the flange surface.
x Connect the lens cable to the ALC lens connector of the camera. 1 3 ALC lens connector 2 4 Pin No. 1 c Secure the camera mount bracket (option) to an installation position, and mount the camera on the camera mount bracket. Important: • If the total weight of the camera and lens exceeds 1 kg {2.2 lbs.}, use a housing to take measures against camera drop. • Prepare mounting screws according to the material of the area where the camera mount bracket (option) is to be installed.
• The mounting conditions of the camera mount bracket are described as follows: Installation place Applicable mount bracket Recommended screw Number of screw Minimum pull-out strength (per 1 pc.) On ceiling WV-7011 M6 4 pcs. 196 N {44.06 lbf} WV-7010 M8 3 pcs. 196 N {44.06 lbf} WV-7012 M6 3 pcs. 196 N {44.06 lbf} WV-831 M8 4 pcs. 921 N {207.05 lbf} WV-7013 M6 3 pcs. 2.25 kN {505.82 lbf} On wall For some applicable mount brackets, "A" is attached to the model number.
v The video output cable is connected to this video output connector. Important: • Be sure to turn off the power of each device before connection. • Be sure to secure the coaxial cable connectors. Connect a coaxial cable to the video output connector. ALARM OUT GND ALARM IN Coaxial cables POWER To video input VIDEO OUT 120V ~ 60Hz WV-CP500 b Use a cable tie (locally procured) to attach the coaxial cable to the camera mount bracket.
External synchronization switch The settings of the alarm input/output are configured on the SETUP menu. Refer to the network operating instructions (PDF) for further information. Important: • Be sure to turn off the power of each device before connection. Alarm output Input specification: Open collector output (max. voltage: 16 V DC) Off: Internally pulled up 2 V to 4 V DC On: Output voltage 1 V DC or less (max.
n Turn on the power. WV-CP500 The included power cord is connected to this power connector. Connect between the power connector on the rear side of the camera and a plug socket with the supplied power cord.
m Adjust the camera angle by loosening the screw of the camera mount bracket while viewing the video monitor. Be sure to loosen the screw of the camera mount bracket when the camera angle is adjusted. If the camera angle is changed when the screw is tight, excessive force is applied to the camera mount bracket and camera, and accordingly they may be damaged. Be sure to tighten the screw securely after camera angle adjustment. , Adjust the focus.
e To perform fine adjustment of the back focus after automatic back focus adjustment, use the right or left button. (No operation for 10 seconds or more closes the setup menu.) Note: • When an auto iris lens is used to record a subject, the originally adjusted focus may be slightly off depending on the iris state resulting from the focal depth of the lens. In such a case, open the aperture by darkening the subject as much as possible in the same way of taking picture, and then adjust the focus.
Setup menu Performing each setting item in the setup menu should be completed in advance to use this unit. Perform the settings for each item in accordance with the conditions of the camera shooting area. Refer to the operating instructions (PDF) for further information. List of setup menu Setup item CAMERA ID This item specifies the camera title.
Setup item Description SPECIAL CHROMA GAIN Adjusts the chroma level. AP GAIN Adjusts the aperture level. PEDESTAL Adjusts the pedestal (brightness) level. HUE Adjusts the chroma phase (hue). PIX OFF Corrects image defects such as flaws. COMMUNICATION Performs the communication setting of the system with a receiver into which this unit is integrated. CAMERA RESET Restores the settings in the setup menu to the default settings. SER.NO. Displays the serial number of this unit.
Basic operation The description below explains how to operate the setup menu basically. The operations in the setup menu are performed with the operation buttons (☞ pages 9 and 10) after calling up the setup menu on the connected video monitor. The operations in the setup menu can also be performed through the system controller (option). Screenshot 1 Hold down the setting button for approx. 2 seconds to call up the top screen of the setup menu.
Screenshot 3 The selected setup screen in the setup menu appears on the screen. **CAMERA SETUP** SCENE1 ALC/ELC ALC SHUTTER OFF AGC ON(HIGH) SENS UP OFF WHITE BAL ATW1 DNR HIGH BW MODE AUTO1 i-VMD RET TOP END Note: • If the top screen of the setup menu is called up with the operation buttons while a camera image is displayed, the setup mode is always "DISABLE" to prevent operation errors. To perform settings in the setup menu, change the setup mode to "ENABLE".
Screen transition diagram Top screen MODEL WV-CP500 SERIES CAMERA ID OFF CAMERA SYSTEM BACK-FOCUS SPECIAL LANGUAGE END SETUP ENABLE "CAMERA ID" screen **CAMERA ID** 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ ().,'":;&#!?= +-*/%$ SPACE POSI RET TOP END RESET ................
Troubleshooting Before asking for repairs, check the symptoms with the following table. Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table or a problem is not described below. Symptom No image displayed Cause/solution Reference pages • Are the power cord and coaxial cable connected appropriately? → Check whether the connection is appropriately established.
Inspect the power cord, power plug and power connectors periodically. Symptom Cause/solution Reference pages • The power cord, power connector, or power plug is damaged. Use of the damaged cord, connector, or plug may cause electric shock or fire. Disconnect the power plug immediately and request repair to your dealer.
Specifications • General Power source: WV-CP500: 120 V AC 60 Hz WV-CP504: 24 V AC 60 Hz, 12 V DC Power consumption: WV-CP500: 3.2 W WV-CP504: 24 V AC: 3.6 W, 12 V DC: 310 mA Ambient operating temperature: –10 °C to +50 °C {14 °F to 122 °F} Ambient operating humidity: Less than 90 % (non condensing) Video output: VBS: 1.
Functions: Camera title: Light control mode setting: Super Dynamic 5 Electronic shutter speed: AGC: Sensitivity up: White balance: Digital noise reduction: Color/BW: Intelligent VMD (i-VMD): Number of scene file: Privacy zone: Image stabilizer: Electronic zoom: Auto back focus: Display language: Up to 16 characters (alphanumeric characters, marks) ALC/ALC+/ELC ON/ON (i-VMD)/OFF OFF (1/60), 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 s ON (HIG
Panasonic System Solutions Company, Unit Company of Panasonic Corporation of North America www.panasonic.com/business/ For customer support, call 1.800.528.6747 Three Panasonic Way 2H-2, Secaucus, New Jersey 07094 Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 http://www.panasonic.ca Panasonic Sales Company Panasonic Puerto Rico, Inc. AVE 65de Inf, Km 9.
