Operating Instructions Color CCTV Camera Model No. WV-CP290/G WV-CP294E Lens: Option Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. No model number suffix is shown in this manual.
We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standards or other normative documents following the provisions of Directives 2006/95/EC and 2004/108/EC. Vi deklarerar härmed vårt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i överensstämmelse med de standarder eller andra normativa dokument som framställs i direktiv nr 2006/95/ EC och 2004/108/EC.
Important safety instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Limitation of Liability THIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THE THIRD PARTY'S RIGHT. THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRA- PHICAL ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).
Contents Important safety instructions.......................................................................................................... 3 Limitation of Liability....................................................................................................................... 4 Disclaimer of Warranty................................................................................................................... 4 Preface.........................................................................
Preface The WV-CP290,WV-CP294 are surveillance color CCTV cameras equipped with a 1/3 inch CCD solid-state image sensor with 752 of horizontal pixels. Features The WV-CP290,WV-CP294 are provided with the adaptive black stretch function, high resolution of 540 TV lines (horizontal), and minimum luminance of 0.8 lx (C/L),0.05 lx (B/W), F1.4(WIDE) thanks to the adoption of the newly developed digital signal processor. Precautions This product has no power switch.
Do not aim the camera at strong light sources. A light source such as a spot light causes a blooming (light bleeding) or a smear (vertical lines). Smear Bright subject Blooming Turn the circuit breaker off which supplies this product with the power when abnormal conditions are encountered.
Precautions for installation This camera is designed to be used indoors. This camera is not operable outdoors. Installation near an air conditioner, an air cleaner, a vending machine, or the like causes noise. Do not operate this product beyond the specified temperature, humidity or power source ratings. Use this product at temperatures within –10 °C to +50 °C, and humidity below 90 %. The input power source is 12 V DC/24 V AC (WV-CP294) or 220 to 240 V AC (WV-CP290).
Major operating controls and their functions Side view(WV-CP290,WV-CP294) 14 2 5 3 WV CP294CH WV-CP290/CH WV-CP294CH Rear view(WV-CP290) Rear view(WV-CP294) 9 9 D/N ON OFF BS. . ON OFF BLC ON OFF ATW AWC D/ N INT 8 LL VIDEO AC IN 220 - 240V ON a50Hz OF F B. S.
A Flange-back adjustment ring This ring adjusts the back-focal distance or picture focus. Important: • When an object is out of focus because it is too close to the camera, focus on a darker object with the aperture open. B ALC lens connector Supplies power and control signals to an auto iris lens (option). C Lens (option) Important: • The lens mount should be a CS mount (1"-32UN). D Flange-back lock screw [LOCK] Loosen this screw with a screwdriver to adjust the flange-back adjustment ring.
• Backlight compensation selector [BLC] ON: Compensates the background automatically if it is brighter than the object. OFF: This mode is used when the front of the object is extremely bright. Default setting: OFF Note: • Under conditions such as extremely strong backlight, the desired compensation effect may not be achieved even with this mode set to ON to detect the backlight level. • White balance selector[ATW/AWC] ATW: Activates the automatic color temperature tracking mode.
Installation and Connection Caution: • Be sure to connect the grounding lead to the GND terminal (WV-CP290). 1 Rotate the lens (option) clockwise slowly to mount the lens. Protrusion from mount: ø20 mm or less Important: • For use of C-mount lens, use the C-mount adaptor (option). • For prevention of damage to the camera body, use a lens with protrusion of 5.5 mm or less from the flange surface. Protrusion from flange: 5.
2 Connect the lens cable to the ALC lens connector of the camera. 1 3 ALC lens connector 2 4 Pin No. 1 2 3 4 3 Secure the camera mount bracket (option) to an installation position, and mount the camera on the camera mount bracket. Important: • The camera mount bracket shall be mounted on the foundation part of the construction or a part with adequate strength. • Recommended screw M6, minimum pull-out strength196 N.
4 The coaxial cable(procured locally) is connected to this video output connector. Important: • Be sure to turn off the power of each device before connection. • Be sure to secure the coaxial cable connectors. Connect a coaxial cable to the video output connector. D/N ON OFF BS. . ON OFF Coaxial cables BLC ATW ON OFF AWC INT To video input LL VIDEO AC IN 220 - 240V OUT ~50Hz WV-CP290 5 Use a cable tie (locally procured) to attach the coaxial cable to the camera mount bracket.
6 Turn on the power. WV-CP290 The included power cord is connected to this power connector. Connect between the power connector on the rear side of the camera and a plug socket with the supplied power cord. D/ N ON OFF Power cord (accessory) BS. . ON OFF BLC ON OFF ATW AWC INT LL VIDEO 220 to 240 V AC, 50 Hz AC IN OUT 220-240V ~ 50 Hz Caution: • The camera shall be connected with cord set with plug.
7 Adjust the camera angle by loosening the screw of the camera mount bracket while viewing the video monitor. Be sure to loosen the screw of the camera mount bracket when the camera angle is adjusted. If the camera angle is changed when the screw is tight, excessive force is applied to the camera mount bracket and camera, and accordingly they may be damaged. Be sure to tighten the screw securely after camera angle adjustment. 8 Adjust the focus position.
Troubleshooting Before asking for repairs, check the symptoms with the following table. Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table or a problem is not described below. Symptom No image displayed Blurred image Image Distortion Cause/solution Reference pages • Are the power cord and coaxial cable connected appropriately? → Check whether the connection is appropriately established.
Inspect the power cord, power plug and power connectors periodically. Symptom Damaged power cord sheathing Heated portion of power line consisting of power cord, connector, and power plug during use The power cord gets hot when bent or stretched. 18 Cause/solution Reference pages • The power cord, power connector, or power plug is damaged. Use of the damaged cord, connector, or plug may cause electric shock or fire. Disconnect the power plug immediately and request repair to your dealer.
Specifications Power source and power consumption: Image sensor: Effective pixels: Scanning area: Scanning system: Scanning frequency: Scanning: Synchronization: Resolution: Minimum illumination: Signal-to-noise ratio: Video output: Lens mount: White balance: Switch function: Ambient temperature: Ambient humidity: Dimensions: Weight: WV-CP290: 220 V-240 V AC 50 Hz, 3.2 W WV-CP294: 24 V AC 50 Hz, 2.9 W, 12 V DC, 240 mA 1/3 inch interline transfer CCD 752 (H) x 582 (V) 4.9 mm (H) x 3.
Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households) This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis.
Panasonic Corporation http://panasonic.net Importer's name and address to follow EU rules: Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15, 22525 Hamburg F.R.Germany © Panasonic System Networks Co., Ltd.
