(Lens : option) Before attempting to connect or operate this product, please read these instructions completely.
ENGLISH VERSION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is interned to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
H The wires in this mains lead are coloured in accordance with the following code. Green-and-yellow: Earth Blue: Neutral Brown: Live As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol I or coloured green or green-and-yellow.
CONTENTS PREFACE ........................................................................................................................................................................ 3 FEATURES ...................................................................................................................................................................... 3 PRECAUTIONS ......................................................................................................................................
PREFACE Panasonic’s WV-BP330 series digital cameras introduce a new level of high picture quality and high resolution through the use of a 1/3-inch interline transfer CCD image sensor having 752 horizontal pixels (pic- ture elements), and digital signal processing LSI’s. This model offers cutting-edge technology for advanced video surveillance. FEATURES 1. The following functions are built-in.
PRECAUTIONS 5. Clean the CCD faceplate with care. Do not clean the CCD with strong or abrasive detergents. Use lens tissue or a cotton tipped applicator and ethanol. 1. Do not attempt to disassemble the camera. To prevent electric shock, do not remove screws or covers. There are no user serviceable parts inside. Ask a qualified service person for servicing. 6. Never face the camera towards the sun. Do not aim the camera at bright objects.
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS LL OFF ELC OFF DC Hi-Z GEN-LOCK INT AGC ON ALC BLC ON VIDEO G/L 75 Ω VIDEO OUT WV- V. PHASE VIDEO LEVEL L H DC 12V IN OFF ELC OFF DC Hi-Z GEN-LOCK AGC ON ALC BLC ON VIDEO G/L 75 Ω VIDEO OUT VIDEO LEVEL L H AC 24V IN GND 1 2 GEN-LOCK LL OFF ELC OFF DC Hi-Z INT AGC ON ALC BLC ON VIDEO G/L 75 Ω VIDEO OUT V.
q Auto Iris lens Connector This connector is for connecting auto iris lens by a 4-pin male connector supplied as a standard accessory (Part No. YFE4191J100). u AC 24V Input Terminal (AC 24V IN (only WV-BP334)) This terminal is for connecting the 24V AC 50Hz power supply cord. w Back-focal Adjusting Ring This ring is adjusts the back-focal length or picture focus. Rotate this ring clockwise for a C-mount lens or counterclockwise for a CS-mount lens.
!0 Automatic Light Control / Electronic Light Control Selector (ALC , ELC) Lets you select the mode according to the lens type that is used with this camera. ALC: Select this mode when an auto iris lens (ALC lens) is used with this camera. ELC: Select this mode when a fixed iris lens or manual iris lens is used with this camera. DC: Select this mode if you are using the auto iris lens that requires a DC drive signal.
!7 Gen-lock Input Connector (GEN-LOCK) This connector is for connecting an external system for synchronization. Caution: Connect to 12V DC (10.5V-16V) or 24V AC (19.5V-28V) class 2 power supply only. Make sure to connect the grounding lead to the GND terminal when the power is supplied from a 24V AC power source.
CONNECTIONS Resistance of copper wire [at 20°C (68°F)] A. WV-BP330 (220-240V AC 50Hz) Connect the power cord to an electrical outlet of 220-240V AC 50Hz. B. WV-BP332 (12V DC) Connect the power cord to the DC 12V IN terminal on the rear panel of the WV-BP332. Copper wire size (AWG) #24 (0.22mm2) #22 (0.33mm2) #20 (0.52mm2) #18 (0.83mm2) Resistance Ω/m 0.078 0.050 0.030 0.018 Resistance Ω/ft 0.026 0.017 0.010 0.006 • Calculation of maximum cable length between camera and power supply : 10.
C. WV-BP334 (24V AC 50Hz) Video Cable Connect the power cable to the AC 24V IN terminal on the rear panel of the WV-BP334. 1 1. It is recommended to use a monitor whose resolution is at least equal to that of the camera. 2. Set the termination switch to the 75Ω position on the last monitor. A. Use a 75Ω coaxial cable. B. Set the termination switch to the 75Ω position on the last monitor and to the Hi-Z position on the other monitors. Do not change the positions after setting. 2 24 V AC, 50 Hz (19.
Type of coaxial cable Recommended maximum cable length RG-59/U (3C-2V) RG-6/U (5C-2V) RG-11/U (7C-2V) RG-15/U (10C-2V) (m) 250 500 600 800 (ft) 825 1 650 1 980 2 640 3. Wiring precautions: • Do not bend the coaxial cable into a curve whose radius is smaller than 10 times the cable’s diameter. • Never staple the cable, not even with circular staples. Impedance mismatching will occur. • Never crush or pinch the cable.
(2) After connection, assemble the lens connector as follows. Installation of Auto Iris Lens Connector Install the lens connector (YFE4191J100) when using a video drive ALC lens. The installation should be made by qualified service personnel or system installers. (1) Cut the iris control cable at the edge of the lens connector to remove the existing lens connector and then remove the outer cable cover as shown in the diagram below.
Mounting the Lens Caution for Mounting the Lens Caution: Before you mount the lens, loosen the two screws on the ring, and rotate this ring clockwise until it stops. If the ring is not at the end, the inner glass or CCD image sensor may be damaged. The lens mount should be a C-mount or CS-mount (1”32UN) and the lens weight should be less than 450g (0.99 lbs). If the lens is heavier, both the lens and camera should be secured by using the supporter.
FOCUS OR BACK-FOCAL ADJUSTMENT The following adjustment should be made by qualified service personnel or system installers. 3. Tighten the screws on the back-focal adjusting ring. 1. Loosen the screws on the back-focal adjusting ring. Note: If the camera is connected to the Quad System, glare may appear at the edge of the camera picture on the monitor. If this bothers you, adjust the lens focus to reduce the glare.
INSTALLATION OF CAMERA • Mounting from the bottom • Mounting from the top This camera is designed to be mounted from the bottom, as shown below. The mounting hole is a standard photographic pan-head screw size (1/4” - 20). Remove the mount adapter from the bottom of the camera by removing the two fixing screws. Attach the mount adapter to the top as shown in the diagram, then mount the camera on the mounting bracket.
PREVENTION OF BLOOMING AND SMEAR When the camera is aimed at a bright light, such as a spot light, or a surface that reflects bright light, smear or blooming may appear. Therefore, the camera should be operated carefully in the vicinity of extremely bright objects to avoid smear or blooming.
SPECIFICATIONS Pick-up Device: Scanning Area: Synchronization: Scanning System: Scanning: Horizontal: Vertical: Horizontal Resolution: Video Output: Signal-to-Noise Ratio: Electronic Light Control: Minimum Illumination: Gain Control: Lens Mount: Ambient Operating Temperature: Ambient Operating Humidity: Power Source and Power Consumption: 752 (H) x 582 (V) pixels, Interline Transfer CCD 4.9 (H) x 3.
Dimensions (without lens): Weights (without lens): 67 (W) x 55 (H) x 123 (D) mm [2-5/8” (W) x 2-3/16” (H) x 4-13/16” (D)] WV-BP330: 0.635kg (1.40lbs) WV-BP332: 0.445kg (0.98lbs) WV-BP334: 0.470kg (1.04lbs) Weights and dimensions indicated are approximate. Specifications are subject to change without notice. STANDARD ACCESSORIES Body Cap .....................................................................................1 pc. ALC Lens Connector (YFE4191J100) ..........................................
Matsushita Electric Industrial Co., Ltd. Central P.O.
